ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Development of Sintered Wear-Resistant and Heat-Resistant Hardfacing Electrodes

Literature Overview and Core Findings

This 2007 study by Xue Wentao from the Beijing General Research Institute of Mining and Metallurgy describes the development of a sintered wear-resistant and heat-resistant hardfacing electrode using a cold-bonding extrusion method. The electrode was designed to produce a hardfacing layer with a combination of wear resistance, heat resistance, and resistance to hot corrosion and high-temperature oxidation. The results showed that the hardfacing alloy achieved an average Rockwell hardness of 55.7, a relative wear resistance of 1.28, and excellent high-temperature oxidation resistance that was superior to the base material.

This is a classic example of the kind of practical, applied research that the hardfacing industry needs. The author did not just develop a new alloy composition; he developed a complete electrode manufacturing process, from the raw materials to the final product, and he validated the performance of the resulting hardfacing layer through a series of tests. The cold-bonding extrusion method is particularly interesting because it is a low-cost, low-energy process that can be easily scaled up for production.

From my perspective, this paper is a reminder that the electrode manufacturing process is just as important as the alloy composition. A good alloy can be ruined by a poor manufacturing process, and a mediocre alloy can be improved by a good manufacturing process. The sintered electrode described in this paper is a good example of the latter: the alloy system is not exotic, but the manufacturing process produces a consistent, high-quality product that performs well in demanding service conditions.

Metallurgical and Process Analysis

The Cold-Bonding Extrusion Process

The cold-bonding extrusion method is a process in which the electrode coating materials are mixed with a binder, extruded through a die to form a coating around the core wire, and then dried and sintered. The key advantage of this method is that it does not require the high-temperature baking that is used in conventional electrode manufacturing, which saves energy and reduces cost. The process also allows for the use of a wide range of coating materials, including powders that would be difficult to incorporate into a conventional coating.

In the development of this electrode, the author used a combination of alloy powders, including ferroalloys, graphite, and other additives, to achieve the desired composition in the hardfacing layer. The coating was designed to provide a source of carbon, chromium, and other alloying elements that would be transferred to the weld metal during the welding process. The sintering step was used to bond the coating materials together and to remove the binder, resulting in a coating that was strong enough to withstand the handling and welding process.

Microstructure and Properties of the Hardfacing Layer

The hardfacing layer produced by this electrode has a microstructure that is typical of the Fe-Cr-C system, with primary carbides in a martensitic matrix. The average hardness of 55.7 HRC is in the range that is expected for this type of alloy, and the relative wear resistance of 1.28 indicates that the hardfacing layer performs significantly better than the base material under abrasive wear conditions.

The high-temperature oxidation resistance of the hardfacing layer was found to be superior to the base material, which is a key requirement for components that operate at elevated temperatures. This is likely due to the formation of a protective chromium oxide layer on the surface of the hardfacing layer, which prevents further oxidation. The resistance to hot corrosion is also important, as many industrial components are exposed to corrosive gases and deposits at high temperatures.

Comparison with Conventional Electrodes

The sintered electrode developed in this study offers several advantages over conventional electrodes. First, the manufacturing process is simpler and more cost-effective, which reduces the cost of the electrode. Second, the coating is more uniform, which results in a more consistent hardfacing layer. Third, the electrode can be formulated with a wider range of alloying elements, which allows for the development of hardfacing layers with tailored properties.

However, there are also some challenges. The sintered coating may be more brittle than a conventional coating, which can cause it to crack or spall during handling or welding. The author addressed this by carefully controlling the sintering temperature and the binder content, but it remains a potential issue in production. Another challenge is that the sintered electrode may have a lower deposition efficiency than a conventional electrode, which means that more electrode is required to deposit the same amount of hardfacing metal.

Integration with Engineering Practice and Quality Control

Practical Application in the Field

The sintered hardfacing electrode described in this paper is well-suited for applications where the component is subject to a combination of abrasive wear, high temperature, and corrosive attack. Typical examples include:

In my experience, the most critical factor in the successful application of a hardfacing electrode is the welding procedure. The electrode must be used with the correct welding parameters, including the current, voltage, travel speed, and preheat temperature. The hardfacing layer must be deposited in the correct pattern, with the proper overlap between beads, to ensure a uniform and defect-free deposit.

Common Defects and Countermeasures

The most common defect associated with sintered hardfacing electrodes is porosity, which can occur if the coating contains moisture or if the welding parameters are not properly set. The countermeasure is to dry the electrodes before use, typically at 200 to 300 degrees Celsius for one to two hours, and to ensure that the welding parameters are within the specified range.

Another common defect is cracking, which can occur if the hardfacing layer is too hard or if the preheat temperature is too low. The countermeasure is to use an adequate preheat temperature, typically 200 to 300 degrees Celsius for high-carbon alloys, and to control the interpass temperature to prevent excessive hardening.

Quality Control and Documentation

The quality control of sintered hardfacing electrodes should include a verification of the coating composition, a check of the electrode dimensions, and a welding test on a test coupon. The welding test should include a visual inspection, a hardness measurement, and a metallographic examination of the hardfacing layer. The results should be documented and kept with the electrode batch records.

Key Questions and Reflections

The most important question that this paper raises is whether the sintered electrode can be produced consistently at a commercial scale. The author developed the electrode in a laboratory setting, and the results are promising, but the transition to commercial production can be challenging. The cold-bonding extrusion process is relatively simple, but it requires careful control of the raw material quality, the binder content, and the sintering conditions. Any variation in these parameters can affect the quality of the electrode and the properties of the hardfacing layer.

Another question is whether the sintered electrode can be used with automated welding processes, such as submerged arc welding or gas metal arc welding. The author used manual welding in the study, which is the most common method for hardfacing, but automated processes offer higher deposition rates and more consistent quality. If the sintered electrode can be adapted for automated welding, it would be a significant advancement.

Study Insights and Implications for the Industry

This paper is a valuable contribution to the hardfacing industry, and it demonstrates that there is still room for innovation in the development of welding consumables. The sintered electrode described in this study offers a cost-effective and high-performance solution for applications that require a combination of wear resistance, heat resistance, and corrosion resistance.

The key takeaway for the practicing engineer is that the manufacturing process of the welding consumable is just as important as the alloy composition. By using a cold-bonding extrusion process, the author has developed a sintered electrode that produces a hardfacing layer with an average hardness of 55.7 HRC, a relative wear resistance of 1.28, and excellent high-temperature oxidation resistance. This is a practical solution that can be implemented on the shop floor with existing welding equipment.

In conclusion, this study by Xue Wentao is a well-executed piece of applied research that addresses a real need in the hardfacing industry. The development of a sintered wear-resistant and heat-resistant hardfacing electrode using the cold-bonding extrusion method is a significant achievement, and the resulting hardfacing layer has properties that are competitive with or superior to conventional hardfacing alloys. The paper provides a clear and practical path forward for the development of new welding consumables, and it deserves the attention of anyone involved in the selection and application of hardfacing materials.