Surfacing Repair of a Crank Precision Forging Lower Die
Failure Analysis of the Forging Die
The paper by Song Jinhu addresses the repair of a crank precision forging lower die, which is a component that is subjected to severe thermal fatigue, wear, and impact. The die is used to forge bicycle crank arms, and the service life is limited by the formation of cracks and the loss of surface material. The failure analysis reveals that the die fails prematurely because of the combination of thermal cycling and abrasive wear.
The die is made of a hot-work tool steel, such as H13 or 5CrNiMo, and the surface is hardened to provide wear resistance. The failure mode is typically thermal fatigue cracking, which is caused by the repeated heating and cooling of the die surface. The cracks propagate from the surface into the die, and eventually, the surface material spalls off.
The paper identifies the main causes of the low service life and proposes a surfacing repair method. The key is to select the right surfacing material and to apply it with the correct process parameters.
Surfacing Material Selection
The selection of the surfacing material for a forging die is a critical decision. The material must have high hardness at elevated temperatures, good thermal fatigue resistance, and good wear resistance. The table below shows the typical options.
| Surfacing Material | Hardness at 500 °C (HRC) | Thermal Fatigue Resistance | Wear Resistance |
|---|---|---|---|
| Martensitic Stainless Steel | 30-35 | Moderate | Moderate |
| Hot-Work Tool Steel | 35-40 | Good | Good |
| Co-Based Alloy | 35-45 | Excellent | Excellent |
| Ni-Based Alloy | 30-40 | Good | Good |
The authors recommend a hot-work tool steel or a cobalt-based alloy for the surfacing of the forging die. The cobalt-based alloy offers the best combination of thermal fatigue resistance and wear resistance, but it is more expensive. The hot-work tool steel is a more economical choice, and it can provide adequate performance if the process parameters are controlled properly.
Surfacing Process and Parameters
The surfacing process for a forging die must be carefully controlled to avoid cracking and distortion. The die is a relatively small component, but the surfacing layer must be deposited uniformly to maintain the die geometry.
| Parameter | Value |
|---|---|
| Surfacing Method | Manual Arc Welding |
| Electrode Diameter | 3.2 mm |
| Welding Current | 100-140 A |
| Arc Voltage | 22-26 V |
| Preheat Temperature | 250-300 °C |
| Interpass Temperature | 300-350 °C |
| Post-Weld Heat Treatment | 500-550 °C for 2 hours |
The preheat temperature is critical for a hot-work tool steel because it has a high carbon content and a tendency to form martensite. A preheat of 250-300 °C is recommended, and the temperature must be maintained throughout the welding process. The interpass temperature must be controlled to avoid overheating, which can cause grain growth and reduce the toughness of the die.
The post-weld heat treatment is essential to relieve the residual stresses and to temper the martensite. The die should be heated to 500-550 °C for 2 hours and then cooled slowly in the furnace. This treatment reduces the hardness of the surfacing layer to the desired level and improves the toughness.
Practical Considerations and Lessons Learned
The paper identifies several problems that can occur during the surfacing process, and the solutions are practical and effective. One of the problems is the formation of cracks in the surfacing layer, which is caused by the high thermal stress. The solution is to control the preheat and interpass temperature, and to use a buttering layer if necessary.
Another problem is the distortion of the die, which is caused by the uneven heat input. The solution is to use a balanced welding sequence and to deposit the surfacing layer in multiple thin passes. The authors recommend a welding sequence that alternates between the two sides of the die to balance the heat input.
I have seen many forging dies that have been repaired with surfacing, and the success of the repair depends on the discipline of the welder and the control of the process parameters. The paper by Song Jinhu provides a clear description of the failure analysis, the material selection, and the process parameters, and it is a valuable reference for any engineer who is faced with a similar repair challenge.
The practical value of this paper lies in its systematic approach to the repair of a forging die. It demonstrates that a proper failure analysis is the first step, and that the surfacing material and process parameters must be selected based on the failure mode. The paper also highlights the importance of post-weld heat treatment, which is often overlooked in practice.
Zhuojin Pipe Fitting Co., Ltd