ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Nitrogen-Alloyed Hardfacing Alloy: Reciprocating Friction and Wear Behaviour

1. Literature Overview and Core Question

This paper by Li Jiaqi and colleagues at Hohai University addresses a problem I have seen burn more than one plant: hardfacing alloys that look great on the hardness tester but fail early in service under cyclic, reciprocating contact. The work introduces nitrogen into martensitic stainless steel, stabilises it with niobium and titanium, and then interrogates the wear behaviour under reciprocating sliding at loads of 5, 10 and 15 N. The core question is simple and brutally practical: does nitrogen alloying actually change the wear mechanism, or is it just another metallurgical curiosity that never survives contact with a real counterface?

The authors compare a nitrogen-alloyed deposit against a conventional one, both on a martensitic stainless steel base, and they do it with a reciprocating friction and wear tester rather than a simple pin-on-disc. That choice matters. Reciprocating motion produces a fundamentally different stress state from unidirectional sliding: the surface experiences periodic reversal of shear direction, which promotes subsurface fatigue crack initiation and delamination. This is exactly the loading seen in valve seats, hydraulic pump components, cam followers and many pipe-handling tools, so the test rig is well chosen.

2. Metallurgical Interpretation of the Nitrogen Effect

The key metallurgical finding is that nitrogen, stabilised by Nb and Ti, forms carbonitrides that precipitate along the martensite matrix and at grain boundaries. These precipitates are fine and dispersed, not coarse and clustered. The authors attribute two strengthening mechanisms to this precipitation: fine-grain strengthening and dispersion strengthening.

Let me unpack this from a shop-floor perspective. In a conventional martensitic stainless steel hardfacing deposit, you get chromium carbides, but they tend to form at grain boundaries in a continuous film, which is a crack path waiting for a load. With nitrogen alloying and Nb/Ti stabilisation, you get carbonitrides that are discrete, rounded and distributed within the grains as well as on boundaries. The result is a microstructure that resists plastic deformation more effectively and, critically, resists the initiation and propagation of subsurface fatigue cracks.

The wear test results support this. The authors report that the nitrogen-alloyed deposit shows fewer and shallower cutting grooves on the worn surface, and significantly less fatigue spalling. The wear mechanism in both alloys is abrasive wear combined with surface fatigue, but the nitrogen-alloyed version resists both. The cutting grooves are shallower because the dispersed carbonitrides increase the matrix hardness and its resistance to ploughing. The fatigue spalling is reduced because the grain boundaries are no longer continuous weak paths; the fine, dispersed precipitates interrupt crack propagation.

3. Practical Implications for Hardfacing Applications

What does this mean for someone specifying or applying hardfacing on pipe mill rolls, forming dies, or valve components? It means that nitrogen alloying is not just a laboratory curiosity. It is a genuine route to improving service life under reciprocating contact, provided the welding process can deliver the required nitrogen content without porosity or loss of nitrogen during solidification.

There is a catch, and I have seen it on the floor. Nitrogen is a strong austenite former, and if the alloy composition is not balanced correctly, you can end up with retained austenite in the deposit, which reduces hardness and can cause dimensional instability. The authors have addressed this by using Nb and Ti as nitride formers, which tie up the nitrogen as carbonitrides rather than leaving it free to stabilise austenite. This is a classic example of alloy design being driven by the welding process constraints, not just by the desired final properties.

The load range tested, 5 to 15 N, is relatively low. In real service, valve seats and roll surfaces can see contact pressures an order of magnitude higher. The trend, however, is clear and consistent: the nitrogen-alloyed deposit outperforms the conventional one at every load tested, and the performance gap widens as load increases. That is the behaviour you want to see before you commit to a new filler wire specification.

4. Critical Assessment and Study Insights

The paper is well executed within its scope, but I would flag two limitations that a practical engineer must keep in mind. First, the test duration is relatively short, and the authors do not report the wear rate as a function of sliding distance beyond the test window. Reciprocating wear is often characterised by an incubation period followed by rapid degradation, and a short test can miss the transition. Second, the counterface material and its surface finish are not described in detail. In real service, the counterface roughness and hardness have a dominant effect on the wear rate of the hardfacing deposit, and a laboratory test with a smooth, hard counterface can overestimate the benefit of a microstructural change.

That said, the metallurgical logic is sound, and I would take this paper as a strong technical justification for evaluating nitrogen-alloyed hardfacing consumables in any application where reciprocating contact is the dominant wear mode. The practical route forward is to commission a trial on an actual component, with a counterface representative of service conditions, and to measure the wear depth as a function of cycles rather than just the final wear scar.

5. Concluding Remarks

Nitrogen alloying of martensitic stainless steel hardfacing deposits, stabilised with Nb and Ti, produces a fine dispersion of carbonitrides that simultaneously strengthens the matrix and interrupts the continuous grain boundary carbide network. The result is a deposit that resists abrasive cutting and surface fatigue spalling under reciprocating contact. This is not a marginal improvement; it is a change in the dominant wear mechanism. For any engineer specifying hardfacing for valve seats, pump components, or roll surfaces that see cyclic contact, this paper justifies a serious evaluation of nitrogen-alloyed consumables. The next step is not more laboratory work, but a service trial on a real component, with real counterface conditions, and a measurement of wear depth versus cycles. That is where the money is made or lost.