Development of Sintered Flux for High-Speed Strip Surfacing of 1Cr13NiMoVNb
Background and Process Requirements
The paper by Wang Xijing, Zhang Dianping, and Wen Xinglin, published in Hot Working Technology in 2006, addresses a very practical production problem: the need for a sintered flux that can support high-speed strip surfacing of a 1Cr13NiMoVNb type alloy. This is not a laboratory curiosity; it is a genuine industrial requirement for applications such as the cladding of pressure vessel internals, reactor components, and rolls used in continuous casting and rolling mills. The 1Cr13NiMoVNb alloy is a martensitic stainless steel with additions of molybdenum, vanadium, and niobium, designed to provide a combination of high strength, good corrosion resistance, and resistance to temper embrittlement. However, this alloy is notoriously difficult to clad at high speeds because of its tendency to form a tenacious oxide film and its sensitivity to the heat input and cooling rate. The authors used an orthogonal experimental design to optimise the composition of a sintered flux, and the result was a flux that provided excellent slag detachability, a smooth and flat bead surface, and a deposited metal composition that met the required specifications.
Flux Composition Optimisation via Orthogonal Experiments
The orthogonal experimental method is the right tool for this problem, and I have used it many times in my own career when developing welding consumables. The challenge with flux formulation is that there are many variables, and the interactions between them are often more important than the individual effects. The authors systematically varied the proportions of the flux components, which typically include SiO2, CaF2, Al2O3, MgO, CaO, and various deoxidizers and alloying elements, and evaluated the results based on arc stability, slag detachability, bead appearance, and the oxidation resistance of the bead surface. The key output was the optimal ratio of components that satisfied all the requirements simultaneously. This is exactly the kind of work that separates a good flux from a mediocre one. In my experience, a flux that produces good slag detachability but poor bead appearance is almost useless, because the operator will spend more time grinding and cleaning than welding. Conversely, a flux that produces a beautiful bead but leaves slag stuck in the corners is a production nightmare, because the slag inclusions will cause defects in the subsequent layer or in the final product.
| Flux Component | Typical Function | Effect on Process Performance |
|---|---|---|
| SiO2 | Slag former, increases viscosity | Too high: poor detachability, rough bead; too low: insufficient protection |
| CaF2 | Decreases viscosity, improves fluidity | Improves slag detachability but reduces arc stability if too high |
| Al2O3 | Increases melting point, stabilises slag | Improves bead shape and reduces oxidation |
| MgO | Basic oxide, improves slag basicity | Improves detachability and reduces hydrogen content |
| CaO | Basic oxide, neutralises acidic components | Improves arc stability and slag fluidity |
| Deoxidizers (Si, Mn, Ti) | Remove oxygen from weld pool | Reduce porosity and inclusions; affect alloy transfer |
Welding Process Performance Analysis
The authors evaluated the flux under the specific welding parameters required for high-speed strip surfacing, which typically involves a strip electrode of around 60 by 0.5 mm or 75 by 0.5 mm, a welding current of 600 to 1200 amperes, a travel speed of 200 to 400 mm per minute, and a welding voltage of 20 to 30 volts. The critical performance indicators were the arc stability, the ease of slag removal, the bead formation, and the oxidation resistance of the bead surface. The results showed that the optimised flux provided a stable arc with minimal spatter, and the slag lifted off cleanly in large pieces, leaving a smooth, shiny bead surface. The chemical composition of the deposited metal was within specification, which confirms that the flux was providing the correct alloy transfer and that the deoxidation was effective. This is a significant result, because high-speed strip surfacing is inherently more demanding than conventional submerged arc welding. The higher travel speed means that the weld pool is smaller and cools faster, which increases the risk of slag entrapment and porosity. The flux must therefore be formulated to have a melting point that is low enough to allow the slag to float to the surface quickly, but not so low that it loses its protective effect.
Practical Application and Lessons
From a production standpoint, the development of this flux is a direct answer to a recurring problem I have encountered in the cladding of large pressure vessels. When the cladding speed is too low, the productivity suffers, and the heat input is high, which can cause distortion of the vessel shell. When the speed is increased without a properly formulated flux, the defects multiply: slag inclusions, lack of fusion, and unacceptable bead profiles. The authors have demonstrated that a systematic approach to flux design, using orthogonal experiments, can resolve these issues. The practical lesson is that flux formulation is not a black art; it is a science that can be approached methodically. The next time you are faced with a cladding problem, do not simply try a different flux from the shelf. Instead, identify the critical performance requirements, set up an orthogonal experiment, and optimise the composition for your specific alloy and welding parameters. This approach will save you time and money in the long run, because you will get a flux that is tailored to your process rather than a generic product that may or may not work. The one caution I would add is that laboratory optimisation is only the first step. The flux must be tested under full production conditions, with the actual strip size, the actual substrate thickness, and the actual joint configuration, because the thermal conditions in a real weld are different from those in a laboratory test plate. Only then can you be confident that the flux will perform consistently in production. This is the kind of work that demonstrates the value of understanding the fundamentals of welding metallurgy and flux chemistry, rather than relying on trial and error.
Zhuojin Pipe Fitting Co., Ltd