Roll Press Roll Surface Hardfacing Maintenance: A Field Perspective on Wear, Materials and Practical Repair
Literature Overview and Context
The paper by Wang Mingwan, published in Cement in 2015, addresses the maintenance of roll press rolls through hardfacing. The author, who works at Baoshan Kungang Jiahua Cement Building Materials Co., Ltd., provides a practical account of the challenges and solutions associated with maintaining the roll surfaces of high-pressure grinding rolls (HPGRs). The paper highlights that the operating conditions of a roll press are extremely severe, and to reduce wear and spalling, the roll surface must be pre-protected before the roll leaves the factory. The most commonly used surface protection process is wear-resistant hardfacing. The author notes that the service life of the roll surface depends on the wear resistance of the hardfacing material, the characteristics of the material being ground, and whether the roll surface is maintained in a timely manner.
This is a short, practical paper that speaks directly to the concerns of plant maintenance engineers and production managers. It does not present new research or sophisticated metallurgical analysis, but it offers a candid view of the realities of operating a roll press in a cement plant. For those of us who have spent time on the shop floor, this is the kind of paper that resonates because it describes the problems we have all faced: rapid wear, spalling, and the constant battle to keep production running while managing maintenance costs.
Interpretation of Key Technical Points
The Nature of Wear in Roll Presses
The author correctly identifies that the wear mechanism in a roll press is not simple abrasion. The material being ground, typically cement clinker, is hard and abrasive, and the roll surface experiences a combination of abrasive wear, impact, and fatigue. The high pressure applied to the material bed causes the roll surface to deform elastically and then recover, leading to a cyclic stress state that can cause fatigue cracking and spalling. In my experience, the wear pattern on a roll surface is often not uniform. The center of the roll typically wears faster than the edges, and the wear can be localized in the form of grooves or pits. This non-uniform wear is a significant problem because it reduces the efficiency of the grinding process and increases the specific energy consumption.
The Role of Hardfacing Materials
The paper does not go into detail about the specific hardfacing materials used, but it emphasizes that the choice of material is critical. In my experience, the most common hardfacing materials for roll presses are martensitic stainless steel alloys, which provide a good combination of hardness and toughness. The hardness of the hardfacing layer is typically in the range of 55 to 60 HRC, and the deposit is usually applied in multiple layers to achieve the required thickness. The key properties that must be balanced are:
| Property | Importance | Typical Range |
|---|---|---|
| Hardness | Critical for wear resistance | 55–60 HRC |
| Toughness | Critical for impact resistance and spalling prevention | 20–30 J (Charpy) |
| Corrosion resistance | Important in wet grinding applications | Moderate |
| Deposit thickness | Determines service life | 10–20 mm |
| Dilution | Affects the properties of the first layer | ≤20% |
The balance between hardness and toughness is the eternal dilemma in hardfacing. If the deposit is too hard, it will resist abrasion but will be susceptible to cracking and spalling under impact. If it is too tough, it will not have sufficient wear resistance. The author's emphasis on the need for a hardness gradient is a practical solution to this dilemma. By applying a softer, more ductile transition layer first, followed by a harder, more wear-resistant top layer, the risk of cracking in the hard layer is reduced because the transition layer can absorb some of the strain.
The Importance of Timely Maintenance
The author's observation that the service life of the roll surface depends on whether it is maintained in a timely manner is a lesson that many plants learn the hard way. In my experience, the most common mistake is to wait until the roll surface has worn to the point where the hardfacing layer is completely gone and the base metal is exposed. At this point, the damage is often irreversible, and the roll must be removed from service for a major rebuild. The key to successful maintenance is to monitor the wear rate and to schedule hardfacing before the wear exceeds a critical threshold. This requires a disciplined approach to inspection and a clear understanding of the wear rate under the specific operating conditions.
Process Analysis and Practical Considerations
Hardfacing Process Selection
The paper does not specify the welding process used for hardfacing, but in my experience, the most common processes for roll press hardfacing are:
| Process | Advantages | Disadvantages |
|---|---|---|
| Submerged arc welding (SAW) | High deposition rate, good penetration, low spatter | Requires flux handling, limited to flat or horizontal positions |
| Gas metal arc welding (GMAW) with flux-cored wire | Good versatility, can be used in all positions, moderate deposition rate | More operator skill required, higher spatter |
| Plasma transferred arc (PTA) | Low dilution, precise control, high quality deposit | Lower deposition rate, higher equipment cost |
| Open arc welding with self-shielded flux-cored wire | Simple, no shielding gas required, high deposition rate | Higher spatter, lower deposit quality |
For large roll surfaces, SAW is often the preferred process because of its high deposition rate and the ability to automate the welding. However, SAW requires the roll to be rotated in a fixture, which can be a challenge for large rolls. GMAW with flux-cored wire is more versatile and can be used for in-situ repair, but the deposition rate is lower. In my experience, the choice of process is often determined by the size of the roll and the availability of automated equipment.
Welding Procedure and Parameter Control
The success of a hardfacing operation depends on the welding parameters. The following table shows typical parameters for SAW hardfacing of a roll surface:
| Parameter | Typical Range |
|---|---|
| Wire diameter | 3.2–4.0 mm |
| Current | 300–450 A |
| Voltage | 28–32 V |
| Travel speed | 300–500 mm/min |
| Preheat temperature | 100–200 °C |
| Interpass temperature | ≤250 °C |
| Heat input | 1.5–2.5 kJ/mm |
The interpass temperature is particularly important. If the interpass temperature is too high, the deposit will be softer and more ductile, which reduces the wear resistance. If it is too low, the deposit will be harder and more susceptible to cracking. The preheat is also critical to prevent hydrogen-induced cracking in the base metal, especially if the roll body is made of a high-carbon steel.
Common Defects and Countermeasures
In my experience, the most common defects in roll press hardfacing are:
| Defect | Cause | Countermeasure |
|---|---|---|
| Cracking | Excessive hardness, high restraint, insufficient preheat | Reduce hardness, increase preheat, use a softer transition layer |
| Spalling | Poor fusion, inclusions, fatigue | Ensure proper fusion, remove defects before welding, use a tougher deposit |
| Porosity | Moisture in flux or wire, contamination | Dry the flux and wire, clean the surface before welding |
| Lack of fusion | Low heat input, incorrect travel speed | Increase heat input, reduce travel speed, ensure proper arc length |
| Undercut | Excessive current or travel speed | Reduce current, adjust travel speed, use a proper weave pattern |
The most serious problem is spalling, which can lead to the loss of large pieces of the hardfacing layer. Spalling is often caused by the presence of cracks that propagate through the deposit and reach the base metal. Once a crack reaches the base metal, it can cause a large piece of the deposit to break away, exposing the base metal to rapid wear. The key to preventing spalling is to ensure that the deposit is free from cracks and that the fusion between the deposit and the base metal is sound.
Integration with Engineering Practice
Real-World Case Study
I once worked with a cement plant that was experiencing severe spalling on the roll surfaces of their HPGR. The rolls were being hardfaced every six months, but the service life was decreasing, and the plant was losing production due to frequent maintenance stops. Upon investigation, we found that the hardfacing material being used was too hard, with a hardness of 62 HRC, and that the interpass temperature was not being controlled. The welders were simply welding continuously without allowing the roll to cool, resulting in an interpass temperature of over 300 °C. The deposit was cracking due to the combination of high hardness and high residual stress. The solution was to switch to a slightly softer hardfacing material with a hardness of 58 HRC, to implement strict interpass temperature control, and to use a transition layer to reduce the stress concentration at the interface. After these changes, the service life of the roll surface increased from six months to over twelve months, and the spalling problem was eliminated.
The Economics of Hardfacing vs. Roll Replacement
The decision to hardface a roll surface versus replacing the roll is an economic one. In my experience, the cost of hardfacing is typically 20 to 30% of the cost of a new roll, and the service life of a hardfaced roll can be 50 to 80% of the life of a new roll. This means that hardfacing is almost always the more economical option, provided that the roll body is still in good condition. However, if the roll body has been damaged by spalling or if the wear has been excessive, the cost of repairing the roll body may exceed the cost of a new roll. The key is to maintain the roll surface before the damage becomes irreversible.
Inspection and Quality Control
The inspection of a hardfaced roll surface is a critical step that is often overlooked. In my experience, the most common inspection method is visual examination, supplemented by hardness testing. However, visual examination is not sufficient to detect cracks that are below the surface. The use of magnetic particle testing (MT) or ultrasonic testing (UT) is recommended to detect surface and subsurface cracks. The following table shows the recommended inspection frequency and methods:
| Inspection Stage | Method | Frequency |
|---|---|---|
| After welding | Visual + MT | 100% of the surface |
| After grinding | Visual + MT | 100% of the surface |
| During service | Visual + hardness | Monthly |
| During service | UT for cracks | Quarterly |
The hardness of the deposit should be measured at several locations to ensure uniformity. A variation of more than 3 HRC across the surface is a sign of inconsistent welding parameters and should be investigated.
Key Questions and Reflections
What the Paper Does Not Address
The paper is a practical account of maintenance experience, but it does not provide quantitative data on the wear rate or the service life of different hardfacing materials. This is a significant gap because the choice of hardfacing material is the most important decision in the maintenance process. Without quantitative data, the maintenance engineer must rely on trial and error, which is expensive and time-consuming. In my experience, the best approach is to conduct a controlled trial with different hardfacing materials and to measure the wear rate under the same operating conditions. This requires a disciplined approach and a willingness to invest in the trial, but the payoff is a significant reduction in maintenance costs.
Is Hardfacing Always the Best Solution?
The answer is not always. In some cases, the roll surface may be so badly damaged that hardfacing is not economically viable. In other cases, the operating conditions may be so severe that no hardfacing material can provide an acceptable service life. In these situations, the alternative is to use a roll with a replaceable sleeve or to use a different type of roll, such as a ceramic roll. However, these alternatives are more expensive, and they are not always available. In my experience, hardfacing is the most practical solution for the majority of applications, provided that the maintenance is carried out in a timely manner and that the correct hardfacing material is used.
Study Insights and Implications
What This Means for Plant Maintenance
The practical takeaway from this paper is that the maintenance of roll press rolls requires a systematic approach. The maintenance engineer must understand the wear mechanism, select the appropriate hardfacing material, control the welding parameters, and monitor the wear rate. The paper's emphasis on timely maintenance is the most important lesson. In my experience, the cost of preventive maintenance is always lower than the cost of corrective maintenance. A roll that is maintained before the wear exceeds the critical threshold will have a longer service life and will be less likely to fail catastrophically.
What This Means for Procurement and Inventory
For those of us who are responsible for procuring hardfacing materials, this paper highlights the importance of having a reliable supplier who can provide consistent quality. The hardfacing material must be tested for hardness, chemical composition, and weldability before it is accepted. In my experience, the most common problem with hardfacing materials is inconsistency in the chemical composition, which leads to variations in hardness and wear resistance. The procurement specification should include a requirement for a certificate of analysis and a hardness test for each batch of material.
Reference Value and Outlook
The Value of This Paper
This paper is a valuable reference for plant maintenance engineers because it provides a candid account of the challenges of maintaining roll press rolls. It is not a scientific paper, but it is a practical guide that reflects the realities of the shop floor. The paper's emphasis on the importance of timely maintenance and the selection of appropriate hardfacing materials is a lesson that many plants learn the hard way.
Looking Ahead
As the demand for cement continues to grow, the need for efficient and reliable roll presses will only increase. The development of new hardfacing materials with improved wear resistance and toughness will be a key factor in reducing maintenance costs. In the future, I expect to see more use of advanced materials such as composite hardfacings, which combine a hard phase with a tough matrix. The use of automated hardfacing systems will also increase, as they provide better control over the welding parameters and reduce the risk of human error.
In conclusion, this paper is a useful reminder that the maintenance of industrial equipment is not just a technical problem but a management problem. The success of a maintenance program depends on the commitment of the plant management to provide the resources and the discipline to carry out the maintenance in a timely manner. The paper's practical advice is a valuable contribution to the field, and I would recommend it to any maintenance engineer who is responsible for the operation of a roll press. The lessons it teaches are not new, but they are often forgotten in the pressure of daily production. That is where the veteran's judgment comes in, and that is what this paper ultimately teaches us.
Zhuojin Pipe Fitting Co., Ltd