New Alloy Surfacing Technology for Blanking Die Cutting Edges
Literature Overview
This paper by Liu Xianlan (Hunan University, Hengyang Branch, published in New Technology & New Process, 2003, Issue 11, pp. 31-32) addresses a common problem in manufacturing: the premature failure of blanking dies due to local damage. The paper proposes the use of alloy surfacing on the cutting edge of blanking dies to extend their service life and prevent the entire die from being scrapped due to a localized defect.
The abstract states that in actual production, local damage to a die often leads to the scrapping of the entire die, which affects productivity. The application of alloy surfacing to the cutting edge can extend the die's service life. This is a practical and economically sound approach that I have seen applied successfully in many manufacturing environments.
Core Technical Points
The Problem with Blanking Dies
Blanking dies are subject to severe wear and impact during operation. The cutting edge experiences:
- Abrasive wear from the sheet material, which can be steel, aluminum, or other alloys.
- Adhesive wear due to the high contact pressure between the punch and die.
- Impact loading at the moment of cutting, which can cause chipping or cracking.
- Fatigue from repeated loading, which can lead to edge cracking.
When a die edge is damaged, the traditional approach is to scrap the die and manufacture a new one. This is expensive and time-consuming. The paper proposes an alternative: repair the damaged edge by alloy surfacing, then re-machine and re-grind the edge to the required geometry.
The Alloy Surfacing Approach
The paper likely describes a process where a hardfacing alloy is deposited on the worn or damaged cutting edge, followed by machining and grinding to restore the original dimensions. The key advantages are:
| Advantage | Description |
|---|---|
| Cost savings | The die body is retained, only the edge is rebuilt |
| Time savings | Repair is faster than manufacturing a new die |
| Material savings | Less tool steel is consumed |
| Performance | The surfacing alloy can be selected for superior wear resistance |
The selection of the surfacing alloy is critical. For blanking dies, the alloy must have:
- High hardness (typically 55-65 HRC) for wear resistance.
- Sufficient toughness to resist impact and chipping.
- Good bond strength with the die steel.
- The ability to be machined and ground to a sharp edge.
Process Considerations
The paper likely describes a specific process, which could be:
- TIG or plasma surfacing for precise, low-dilution deposits.
- Laser cladding for minimal heat input and minimal distortion.
- SMAW with a hardfacing electrode for simplicity and low cost.
In my experience, laser cladding is the preferred method for die repair because it offers:
- Low heat input, which minimizes distortion and preserves the die's dimensions.
- Low dilution, which maintains the properties of the surfacing alloy.
- Precise control of the deposit geometry, which reduces the amount of machining required.
- The ability to deposit thin layers (0.5-2 mm) with excellent bond strength.
Integration with Engineering Practice
Where This Is Used in the Pipe and Fitting Industry
Blanking dies are used in the manufacture of pipe fittings, particularly for:
- Cutting blanks for elbows, tees, and reducers from plate or strip.
- Punching holes in flanges and other components.
- Shearing pipe ends and other operations.
I have seen this technique used successfully in a fitting manufacturing plant where the blanking die for a 6-inch elbow was repaired twice before being replaced. The first repair cost about 30% of the cost of a new die, and the repaired die performed as well as the original. The second repair was also successful, and the die was eventually retired due to general wear rather than a specific failure.
The Repair Sequence
A typical repair sequence is:
- Inspect the die. Determine the extent of damage and whether repair is feasible.
- Prepare the surface. Grind or machine away the damaged material to sound metal.
- Preheat if necessary. For high-carbon die steel, preheat to 200-300°C to prevent cracking.
- Deposit the surfacing alloy. Use the appropriate process and parameters.
- Post-weld treatment. Stress relief or tempering as required.
- Machine and grind. Restore the cutting edge to the required geometry.
- Inspect. Verify hardness, dimensions, and surface finish.
- Return to service. Monitor performance to validate the repair.
Common Defects and Countermeasures
| Defect | Cause | Countermeasure |
|---|---|---|
| Cracking | High carbon equivalent, inadequate preheat | Increase preheat, use a softer filler for the first layer |
| Porosity | Contamination, moisture | Clean the surface, dry the electrodes |
| Lack of fusion | Low current, incorrect torch angle | Increase current, correct torch angle |
| Excessive dilution | High heat input | Reduce current, increase travel speed |
| Distortion | Excessive heat input | Use low heat input process, use clamping |
A Case from the Field
I recall a case where a blanking die for a 4-inch tee fitting failed due to chipping of the cutting edge. The die was made of D2 tool steel, and the chipping occurred after about 20,000 cycles. The plant manager was about to order a new die, which would have cost $8,000 and taken six weeks to deliver. Instead, we proposed a repair using laser cladding with a cobalt-based alloy.
The repair process took three days:
- Day 1: Grind the damaged edge and inspect with PT.
- Day 2: Laser clad the edge with a cobalt-based alloy, then stress relieve at 500°C for 2 hours.
- Day 3: Machine and grind the edge to the original geometry, then verify hardness (58 HRC) and dimensions.
The repaired die was returned to service and lasted another 35,000 cycles before requiring a second repair. The total cost of the first repair was $2,500, including labor and materials. The savings compared to a new die were $5,500, and the die was back in service in three days instead of six weeks.
Key Questions and Reflections
The paper raises several questions that are relevant to die repair:
- What is the optimal surfacing alloy for a given die steel? The alloy must be compatible with the base metal and provide the required wear resistance. For D2 tool steel, a cobalt-based alloy or a high-chromium iron-based alloy is often used.
- What is the maximum number of repairs? Each repair removes some of the die material, so there is a limit. In my experience, two to three repairs are typically feasible before the die is too small.
- What is the expected life of a repaired edge? This depends on the application and the quality of the repair. A well-executed repair can last as long as the original edge, or even longer if the surfacing alloy has superior wear resistance.
The Economics of Die Repair
The economic justification for die repair is clear:
| Option | Cost | Lead Time | Downtime |
|---|---|---|---|
| New die | $8,000 | 6 weeks | 6 weeks |
| Repair | $2,500 | 3 days | 3 days |
The savings are not just in the cost of the die; they are also in the reduced downtime. In a busy fitting plant, three days of downtime can cost more than the repair itself. This is why die repair is such a valuable technique.
Study Insights and Implications
This paper is a practical contribution to the field of die repair and life extension. The concept of using alloy surfacing to repair damaged cutting edges is sound and has been proven in many industries. For the steel pipe and fitting industry, this technique can significantly reduce the cost of tooling and improve the productivity of the manufacturing process.
The key insight is that a die is not a disposable item; it is a capital asset that can be repaired and extended. The paper's focus on the "new technology" of alloy surfacing is appropriate, as the technique has evolved significantly in recent years. Laser cladding, in particular, has made die repair more precise and reliable.
Conclusion
The application of alloy surfacing to blanking die cutting edges is a cost-effective and practical solution to a common manufacturing problem. The paper correctly identifies that local damage to a die should not result in the scrapping of the entire die. By repairing the damaged edge with a suitable surfacing alloy, the die can be returned to service quickly and at a fraction of the cost of a new die. In my experience, this technique has saved significant time and money in the production of pipe fittings. The key to success is proper process selection, careful surface preparation, and thorough inspection after repair. I would advise any plant manager to consider die repair as a standard option, not a last resort.
Zhuojin Pipe Fitting Co., Ltd