Effect of Rare Earth Ferrosilicon Powder on Microstructure and Properties of Hypereutectic High-Chromium Surfacing Alloy
Why This Topic Deserves Attention
High-chromium hardfacing alloys are the workhorse of wear-resistant overlays in the steel pipe and fitting industry. We use them on guide rolls, forming rolls, shear blades, and any surface that sees abrasive wear. The problem is always the same: how do you get the hard carbides to be fine, uniformly distributed, and in the right volume fraction? This paper tackles that problem by adding rare earth ferrosilicon powder to the flux-cored wire.
The key results are straightforward and useful:
| Rare Earth Ferrosilicon Content | Hard Phase Characteristics | Hardness | Wear Behavior |
|---|---|---|---|
| 0% (baseline) | Coarse, irregular carbides | HRC 55 | Higher wear loss |
| 10% | Regular hollow hexagonal M7C3, fine and uniformly distributed | HRC 65 | Minimum wear loss |
| >10% | Carbides smaller but fewer in number | Hardness decreases | Wear loss increases |
What the Microstructure Tells Us
The 10% addition is the sweet spot. At this level, the M7C3 carbides form as regular hollow hexagonal structures — this is a classic primary carbide morphology in hypereutectic high-chromium alloys. The rare earth elements refine the grains and promote more uniform carbide nucleation. The result is a harder, more wear-resistant overlay.
The metallurgical mechanism is worth understanding. Rare earth elements have a high affinity for oxygen and sulfur. They act as deoxidizers and desulfurizers in the weld pool, which reduces the number of inclusions that can serve as nucleation sites for coarse carbides. They also segregate to the carbide/matrix interface and lower the interfacial energy, which promotes finer carbide growth.
Practical Application in Pipe and Fitting Production
In our shop, we use high-chromium hardfacing on forming rolls for ERW pipe production. The rolls see continuous abrasive wear from the strip edge, and a roll that wears out prematurely means downtime and dimensional drift on the pipe.
The 10% rare earth addition gives us HRC 65, which is a significant improvement over the HRC 55 baseline. In practice, this translates to longer roll life and more consistent pipe dimensions over a production run.
The key is to control the rare earth addition precisely. Too little and you do not get the refinement. Too much and the carbides become sparse and the hardness drops. The paper shows that the wear loss follows a U-shaped curve — it decreases up to 10% and then increases. This is a classic case of an optimal addition level.
The Critical Control Point
The most important practical takeaway is the need for tight control of the rare earth content in the flux-cored wire. In production, this means:
- Verify the rare earth content in the incoming powder. Do not assume the supplier's certificate is accurate — test it.
- Control the wire manufacturing process to ensure uniform distribution of the rare earth powder in the flux core. Segregation in the wire will cause inconsistent properties along the weld.
- Monitor the hardness of the deposited layer on a regular basis. A drop from HRC 65 to HRC 60 is a warning sign that the rare earth content has drifted.
- Check the wear performance in actual service, not just in the laboratory. The lab test gives you a ranking, but the real wear mechanism on a forming roll is different from a pin-on-disk test.
My Reflection
This is a well-designed study that gives a clear answer to a practical question. The 10% rare earth addition is not a magic number — it is the result of a systematic investigation, and it will vary with the base alloy composition and the welding process. If you are using a different high-chromium alloy or a different surfacing process, you need to do your own optimization.
The hollow hexagonal M7C3 morphology is particularly interesting. This is not a common carbide shape, and it suggests that the rare earth elements are not just refining the grains but also modifying the carbide growth mechanism. This is the kind of fundamental insight that can lead to better alloy design.
Key Takeaways
- Rare earth ferrosilicon powder at 10% of the flux core content significantly improves the hardness and wear resistance of hypereutectic high-chromium surfacing alloy.
- The optimal addition level is critical — too little gives no benefit, too much degrades the properties.
- The M7C3 carbides with hollow hexagonal morphology are the key microstructural feature that correlates with the best wear performance.
- In production, tight control of the rare earth content in the flux-cored wire is essential for consistent results.
- Always verify the actual wear performance in service, not just in the laboratory.
The practical value of this work is that it gives you a target to aim for. When you are specifying a flux-cored wire for hardfacing, you can now ask your supplier for a wire with 10% rare earth ferrosilicon in the flux and expect HRC 65 and good wear resistance. That is a specification you can put on a purchase order.
Zhuojin Pipe Fitting Co., Ltd