Effect of σ Phase on Microstructure and Properties of Duplex Stainless Steel Surfacing Layer
Why This Paper Is Critical Reading
σ phase is the single most dangerous precipitation in duplex stainless steel. It forms in the temperature range of approximately 600–1000°C, and it is a hard, brittle, chromium-rich intermetallic phase. Its formation depletes the surrounding matrix of chromium and molybdenum, which destroys the corrosion resistance. It also increases hardness and reduces toughness.
This paper takes a duplex stainless steel surfacing layer and subjects it to a 900°C heat treatment with different holding times. The goal is to produce different σ phase contents and then evaluate the effect on corrosion resistance and hardness.
| Heat Treatment | Ferrite Content | σ Phase Content | Corrosion Resistance | Hardness |
|---|---|---|---|---|
| As-deposited | >40% | None | Good | Baseline |
| 900°C, short time | <40% | Low | Reduced | Increased |
| 900°C, long time | <40% | High | Severely reduced | Significantly increased |
The Metallurgical Mechanism
σ phase precipitation in duplex stainless steel occurs at the ferrite/austenite phase boundaries. The ferrite phase is enriched in chromium and molybdenum, which are the σ phase formers. When the material is held at 900°C, the ferrite transforms to σ phase and secondary austenite.
The critical issue is the ferrite content. The paper states that after heat treatment, the ferrite volume fraction is below 40%. This is significant because the duplex microstructure depends on a balanced ferrite/austenite ratio. When the ferrite content drops below 40%, the material is no longer a true duplex stainless steel — it has become an austenitic stainless steel with some residual ferrite.
The σ phase precipitation has two effects:
- It directly reduces corrosion resistance because the σ phase itself is chromium-rich and the surrounding matrix is chromium-depleted.
- It indirectly reduces corrosion resistance because the ferrite content is reduced, which changes the overall microstructure.
Practical Implications for Pipe and Fitting Manufacturing
This is not just an academic concern. In the steel pipe industry, duplex stainless steel is used for:
- Seamless pipe for offshore oil and gas service
- Welded pipe for chemical process lines
- Pipe fittings for sour service
- Weld overlays for pressure vessels and reactors
The problem is that duplex stainless steel is sensitive to thermal history. If you weld it without proper interpass temperature control, or if you heat treat it in the wrong temperature range, you will precipitate σ phase and destroy the corrosion resistance.
The 900°C temperature used in this study is in the middle of the σ phase precipitation range. In practice, this means that any process that holds the material at this temperature for an extended period is dangerous.
Real-World Failure Modes
I have seen σ phase problems in real projects. One case involved a duplex stainless steel pipe fitting that was solution annealed at 1050°C but then cooled slowly through the 900°C range. The fitting passed the initial inspection but failed the intergranular corrosion test. Metallographic examination showed extensive σ phase precipitation at the ferrite/austenite boundaries.
Another case involved a weld overlay on a pressure vessel. The overlay was applied with a high heat input process, and the interpass temperature was not controlled. The result was σ phase precipitation in the heat-affected zone of the overlay, which caused pitting corrosion during hydrostatic testing.
How to Prevent σ Phase Precipitation
- Control the welding heat input. Use a low heat input to minimize the time spent in the 600–1000°C range.
- Control the interpass temperature. Keep it below 150°C for duplex stainless steel.
- Use a rapid cooling rate after welding. Water quenching is preferred for small components.
- If post-weld heat treatment is required, use a solution anneal at 1050–1100°C followed by rapid cooling. Do not use a stress-relief treatment in the 600–1000°C range.
- Verify the ferrite content after welding. Use a ferrite scope or metallographic examination to confirm that the ferrite content is in the acceptable range.
My Reflection
This paper is a good example of the connection between microstructure and performance. The σ phase is not just a laboratory curiosity — it is a real problem that causes failures in the field.
The key insight is that the ferrite content is the indicator. If you measure the ferrite content and it is below 40%, you have a problem. The σ phase has already precipitated, and the corrosion resistance is compromised.
The hardness increase is also a useful indicator. If you measure the hardness of a duplex stainless steel weld and it is significantly higher than expected, σ phase may be present.
Key Takeaways
- σ phase precipitation in duplex stainless steel occurs in the 600–1000°C range and severely degrades corrosion resistance.
- Ferrite content below 40% is a sign that σ phase has formed.
- Hardness increases with σ phase precipitation, which can be used as a diagnostic indicator.
- Control of welding heat input and interpass temperature is essential to prevent σ phase formation.
- Solution annealing at 1050–1100°C followed by rapid cooling is the only effective way to dissolve σ phase.
The practical value of this work is that it gives you a clear diagnostic criterion. If you measure ferrite content below 40% or hardness above the expected range, you know that σ phase has formed and the component is at risk. This is the kind of information that prevents failures before they happen.
Zhuojin Pipe Fitting Co., Ltd