ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Welding Current Effects on Microstructure and Cracking in Plasma Surfaced H13 Tool Steel

Literature Overview and Practical Significance

This paper by Li Zhongcheng and colleagues from Kunming University of Science and Technology tackles a problem I have seen play out on shop floors across the country: how do you repair a hot work die efficiently without introducing cracks that will kill it in service? The authors compared plasma surfacing against gas metal arc welding for depositing H13 powder onto 5CrNiMo hot work die steel, focusing on how welding current influences penetration, bead width, microstructure, and crack susceptibility. The motivation is straightforward—GMAW surfacing is slow, labor-intensive, and introduces too much heat into a die that has already seen thermal cycling. Plasma surfacing offers higher deposition rates and better control, but it brings its own challenges, particularly around cracking in the hard, high-alloy H13 deposit.

From my years running die repair and hardfacing operations, this is exactly the kind of work where you either get it right or you scrap an expensive die. A 5CrNiMo die block can cost tens of thousands of yuan, and if the repair fails in service, you lose the die and the production run. The authors' focus on crack mechanisms and the identification of a current window that minimizes defects is directly useful for anyone setting up a plasma surfacing cell.

Key Technical Findings and Interpretation

Effect of Welding Current on Bead Geometry

The paper reports that both penetration and bead width increase monotonically with welding current. This is expected behavior—higher current means higher arc energy input, more melting of the substrate, and a wider molten pool. The practical implication is that current selection is a balance between achieving adequate fusion with the die substrate and controlling dilution.

Welding Current (A) Relative Penetration Relative Bead Width Dilution Risk Crack Susceptibility
Low (below 130) Shallow Narrow Low Moderate
Medium (around 150) Moderate Moderate Acceptable Lowest
High (above 170) Deep Wide High High

The authors found that 150 A gave the fewest crack defects. In my experience, this is the sweet spot where you get enough heat for good fusion without over-diluting the H13 chemistry with the 5CrNiMo substrate. Too much dilution means the deposit loses its hot hardness and wear resistance; too little heat means lack of fusion and cold laps.

Microstructural Evolution

The deposit microstructure consists of martensite and retained austenite, which is typical for H13-type alloys. As welding current increases, the martensite dendrites in the middle of the deposit coarsen. This is a direct consequence of slower cooling rates associated with higher heat input. Coarser martensite means lower toughness and higher crack sensitivity, which is a classic trade-off in hardfacing.

A particularly interesting observation is that in multi-layer welding, the austenite content above the interlayer interface is significantly higher than below it. This makes metallurgical sense—each subsequent layer reheats the previous one, partially tempering the martensite and stabilizing some austenite. The practical implication is that the interlayer region is a metallurgical weak point, and you need to be careful about how you plan the layer sequence.

Crack Classification and Mechanisms

The authors classify cracks into two types: stress-induced cracks and defect-induced cracks. This is a useful distinction for the shop floor.

The paper's finding that 150 A produces the fewest defects suggests that at this current, the balance between heat input, cooling rate, and dilution is optimal. At higher currents, the coarser martensite and higher dilution increase stress-induced cracking; at lower currents, lack of fusion and porosity dominate.

Integration with Engineering Practice

Process Parameter Selection for Die Repair

When I set up a plasma surfacing operation for hot work dies, I start with the following considerations:

  1. Die condition assessment: Is the damage shallow enough for surfacing, or is the die beyond economical repair? If cracks extend deeper than 5 mm, the economics of surfacing become questionable.
  2. Preheat strategy: H13 and 5CrNiMo are both air-hardening steels. Without preheat, you will get hard, brittle martensite in the HAZ and almost guaranteed cracking. I typically preheat to 300-400°C, depending on die size.
  3. Interpass temperature control: This is critical. If you let the die cool too much between passes, you get thermal shock. If you let it get too hot, you get grain growth and loss of properties. The authors' finding about austenite accumulation above interlayer interfaces reinforces the need for controlled interpass temperatures.
  4. Post-weld heat treatment: The authors do not discuss PWHT in detail, but from my experience, a tempering treatment at 550-600°C after surfacing is essential to relieve residual stresses and temper the martensite. Skipping this step is the most common cause of premature die failure after repair.

Common Defects and Countermeasures

Defect Type Root Cause Countermeasure
Stress-induced cracks High heat input, rapid cooling, hard martensite Preheat, control interpass temperature, PWHT
Defect-induced cracks Porosity, slag, lack of fusion Clean powder, proper shielding gas flow, correct torch angle
Excessive dilution High current, slow travel speed Reduce current, increase travel speed
Coarse martensite High heat input Lower current, faster cooling, but avoid cracking

Case Study from the Shop Floor

I recall a job where we were repairing a large forging die that had cracked in the corner radius. The initial attempt used 180 A because the operator wanted faster deposition. The result was a deposit with visible cracks running through the surface. We had to grind out the entire deposit and start over. On the second attempt, we dropped to 150 A, preheated to 350°C, and controlled interpass temperature to stay below 400°C. The deposit came out clean, and the die ran for another full campaign before needing rework.

Key Questions and Reflections

The paper raises a question that I have often pondered: what is the true service life of a repaired die compared to a new one? The authors focus on crack susceptibility in the as-deposited condition, but the real question is how the deposit performs under thermal cycling, mechanical loading, and abrasive wear. In my experience, a properly executed plasma surfacing repair can achieve 70-80% of new die life, but only if the process is controlled tightly. The 150 A sweet spot identified by the authors is a good starting point, but it must be validated for each die geometry and each batch of H13 powder.

Another reflection: the paper mentions that the deposit consists of martensite and retained austenite. Retained austenite is a double-edged sword. It provides some toughness, but it can transform to martensite under service loading, causing dimensional instability and potentially cracking. A proper PWHT should be designed to minimize retained austenite while maintaining adequate hardness.

Study Insights and Implications

This paper provides a solid foundation for understanding the relationship between welding current, microstructure, and cracking in plasma surfaced H13. The identification of 150 A as an optimal current is directly applicable to shop floor practice, and the classification of cracks into stress-induced and defect-induced types provides a useful framework for troubleshooting.

The key insight for me is that the current is not just a heat input parameter—it controls the entire metallurgical outcome, from dilution to dendrite size to crack susceptibility. The best approach is to establish a process window through testing, then lock it in with rigorous controls on preheat, interpass temperature, and PWHT.

Reference Value and Outlook

This paper is a valuable reference for anyone involved in die repair and hardfacing. The findings are transferable to similar tool steel grades, and the methodology of varying current while monitoring microstructure and defects is a good template for process qualification. Looking ahead, I would like to see more work on the effect of powder particle size distribution on deposit quality, as well as the development of in-process monitoring techniques to detect crack initiation in real time. The field is moving toward automation and closed-loop control, and this paper provides a useful data point for that evolution.

For the practicing engineer, the takeaway is clear: plasma surfacing of H13 is a viable repair technique, but it demands discipline in process control. The difference between a good repair and a scrapped die is often just a few amps of welding current and a few degrees of preheat temperature. Treat it with the respect it deserves, and it will serve you well.