Temperature Effects on Stellite6 and Stellite21 PTA Hardfacing on 304H Stainless Steel
Literature Overview
This study by Yu Shiqing et al. from Shenyang University of Technology and Shenyang Blower Works Group Nuclear Pump Co. Ltd. investigates the microstructure and property evolution of Stellite6 and Stellite21 cobalt-based alloy hardfacing layers deposited on 304H stainless steel by plasma transferred arc (PTA) welding, after exposure to 550-650°C. The paper appeared in Hot Working Technology, Vol. 53, No. 7, 2024.
This is exactly the kind of work that matters when we are specifying hardfacing for nuclear pump components, valve seats, and other high-temperature service parts. The temperature range 550-650°C is not arbitrary - it covers typical operating conditions for superheater valves, turbine bypass valves, and certain pump internals in power generation service.
Microstructure Evolution
The as-welded microstructure consists of three distinct zones: planar crystals at the fusion boundary, columnar crystals in the middle, and equiaxed crystals at the top of the deposit. This is classic solidification behavior for PTA hardfacing - the cooling rate and temperature gradient determine the morphology transition from planar to cellular to dendritic growth.
Key observation: after exposure to 550-650°C, the dendrite arm spacing increases slightly, but no significant elemental diffusion occurs at the fusion boundary. This indicates good metallurgical stability of the deposit at these temperatures.
Hardness and Corrosion Performance
The as-welded hardness values are significant:
| Alloy | As-welded Hardness (HV0.3) | After Thermal Exposure |
|---|---|---|
| Stellite6 | 463 | Slightly reduced |
| Stellite21 | 365 | Slightly reduced |
Stellite6 is harder because it contains more carbon and tungsten carbides, while Stellite21 has lower carbon content and relies more on solid solution strengthening from molybdenum and chromium.
Corrosion current density values:
| Alloy | As-welded (μA/cm²) | After Thermal Exposure |
|---|---|---|
| Stellite6 | 1.312 | Slightly increased |
| Stellite21 | 10.848 | Slightly increased |
The corrosion current density of Stellite21 is roughly 8 times higher than Stellite6, which reflects the lower chromium carbide content and different passive film characteristics. However, both remain in acceptable ranges for the intended service.
Practical Implications
In my experience with valve body hardfacing and pump component repair, the choice between Stellite6 and Stellite21 is often a compromise between hardness and toughness. Stellite6 gives you the wear resistance but can be prone to cracking on thick sections if preheat and interpass temperature are not carefully controlled. Stellite21 is more forgiving, better for impact and thermal shock, but you give up some hardness.
The fact that both alloys maintain their hardness and corrosion resistance after 550-650°C exposure is reassuring for long-term service. However, I would caution that the study only looks at short-term thermal exposure - real service involves thermal cycling, which can cause carbide coarsening and sigma phase precipitation in the substrate HAZ over years of operation.
Key Takeaways
- PTA hardfacing produces a sound metallurgical bond with 304H with no significant interdiffusion at 550-650°C.
- Stellite6 offers higher hardness and better corrosion resistance than Stellite21, but Stellite21 provides better toughness.
- The microstructure is thermally stable in the studied temperature range, but long-term service data is still needed.
Summary
This study provides valuable baseline data for specifying cobalt-based hardfacing on 304H components. For shop floor practice, the key is to maintain proper preheat (typically 150-200°C for Stellite6 on austenitic stainless steel) and control interpass temperature to avoid cracking. The data also confirms that post-weld heat treatment is not required for these deposits in the 550-650°C service range, which simplifies the manufacturing route. I would recommend extending this work to include thermal cycling tests and impact toughness evaluation before finalizing material selection for critical nuclear service components.
Zhuojin Pipe Fitting Co., Ltd