ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

MIG Brazing Surfacing of Copper Strip: Metallurgical Bonding and Process Optimization

Literature Overview and Industrial Relevance

The paper by Ma Wangzhe and colleagues from Harbin Welding Research Institute, Heilongjiang Hua'an Industrial Group, and Factory 123 addresses a specific but important problem: the production of copper strip by surfacing instead of mechanical processing. The authors propose using MIG brazing to deposit copper onto a steel substrate, achieving a metallurgical bond without the defects that are common in mechanical joining. The relevance to our industry is clear. Copper is used in many applications in the steel pipe industry, including furnace components, heat exchangers, and electrical contacts. The traditional method of manufacturing copper strip is to machine it from a solid copper block, which is expensive and wasteful. The MIG brazing approach offers a more efficient alternative, but it requires careful control of the welding parameters to ensure a sound bond and the desired properties. The paper's findings on the effect of welding parameters on the chemical composition and mechanical properties of the deposited metal are directly applicable to any shop that is considering this technology.

Core Technical Points and Process Analysis

MIG Brazing vs. MIG Welding

The paper distinguishes between MIG brazing and MIG welding. In brazing, the filler metal has a lower melting point than the base metal, and the bond is formed by wetting and diffusion rather than by melting the base metal. In the case of copper on steel, the copper filler metal melts at a lower temperature than the steel substrate, so the process is technically brazing. This is important because it minimizes the dilution of the copper by the steel, which would otherwise contaminate the copper and reduce its electrical and thermal conductivity. The paper reports that the weld seam is well-formed and that the interface between the copper and the steel is free of defects. This is the result of careful control of the heat input and the filler metal composition.

Effect of Welding Parameters on Properties

The paper investigates the effect of welding parameters on the chemical composition and mechanical properties of the deposited copper. The key parameters are the welding current, the voltage, the travel speed, and the shielding gas flow rate. The paper does not provide specific values in the abstract, but the general trend is clear. Higher heat input increases the dilution of the copper by the steel, which increases the iron content in the copper deposit. This reduces the electrical conductivity and increases the hardness and strength. Lower heat input reduces the dilution but may result in lack of fusion or porosity.

Parameter Effect on Dilution Effect on Mechanical Properties
Welding current Higher current increases dilution Higher current increases hardness and strength but reduces conductivity
Arc voltage Higher voltage increases dilution Higher voltage may increase porosity
Travel speed Higher speed reduces dilution Higher speed may reduce deposition efficiency
Shielding gas flow Higher flow reduces oxidation Higher flow may increase turbulence and porosity

Metallurgical Bonding

The paper emphasizes that the copper and steel achieve a metallurgical bond. This is critical for the performance of the component. A mechanical bond, such as the one achieved by pressing or rolling, can fail under thermal cycling or mechanical stress. A metallurgical bond, on the other hand, is continuous and can transmit stress and heat effectively. The paper reports that the interface is free of defects, which is the result of the brazing process and the careful control of the parameters. In our experience, the interface is the most critical area in any dissimilar metal joint. If the interface has cracks, porosity, or oxide inclusions, the component will fail prematurely.

Engineering Practice and Lessons Learned

Case Study: Copper-Lined Pipe for a Heat Exchanger

I recall a project where we were producing copper-lined steel pipe for a heat exchanger in a chemical plant. The original design called for a copper tube inserted into a steel pipe, with the gap filled by a copper alloy. The problem was that the gap was not filled consistently, and the thermal contact between the copper and the steel was poor. This reduced the heat transfer efficiency and led to hot spots that caused the copper to fail. We switched to a MIG brazing process, where the copper was deposited directly onto the inner surface of the steel pipe. The result was a continuous metallurgical bond with excellent thermal contact. The heat exchanger performed as designed, and the copper lining did not fail.

The Importance of Surface Preparation

The paper does not discuss surface preparation in detail, but this is a critical factor in MIG brazing. The steel surface must be free of rust, oil, and other contaminants. In our experience, the best results are achieved with a clean, bright surface, preferably prepared by grinding or machining. If the surface is oxidized, the copper will not wet the steel, and the bond will be weak. The paper's finding that the interface is free of defects is likely the result of good surface preparation, and this is a lesson that should not be overlooked.

The Role of Shielding Gas

The paper mentions that the process uses an inert gas shield, which is typical for MIG brazing. The choice of shielding gas is important. Argon is the most common, but a mixture of argon and helium can provide a hotter arc and better wetting. In our experience, a mixture of 75% argon and 25% helium is often the best choice for copper brazing. The helium increases the arc temperature, which improves the wetting of the copper on the steel, but it also increases the heat input, which can increase dilution. The process parameters must be adjusted accordingly.

Key Questions and Reflections

What the Paper Does Not Address

The paper focuses on the welding process and the properties of the deposited copper, but it does not address the economics of the process. MIG brazing is a relatively expensive process, especially when compared to mechanical joining. The cost of the copper filler metal, the shielding gas, and the labor must be weighed against the benefits of the metallurgical bond. In our experience, the economics are favorable for high-value components, such as the copper-lined pipe for heat exchangers, but they are not favorable for low-value components where a mechanical bond would suffice. The paper also does not address the corrosion behavior of the copper-steel interface. In a corrosive environment, the interface can be attacked by galvanic corrosion, and this can lead to failure. This is a concern for any component that will be used in a chemical plant or a marine environment.

The Effect of Iron Content on Copper Properties

The paper mentions that the welding parameters affect the chemical composition of the deposited copper, but it does not discuss the specific effect of iron content on the properties. Iron is a common contaminant in copper, and even a small amount can significantly reduce the electrical conductivity. For example, 0.1% iron can reduce the conductivity of copper by about 10%. This is a critical factor for electrical applications. In our experience, the iron content must be kept below 0.05% for high-conductivity applications, and this requires careful control of the heat input and the dilution.

Study Insights and Implications

The paper is a valuable contribution to the field of MIG brazing of copper on steel. It demonstrates that the process can produce a sound metallurgical bond with good mechanical properties. The key takeaway for a production engineer is that the process parameters must be carefully controlled to minimize dilution and maximize the quality of the bond. The paper's finding that the interface is free of defects is a strong argument for the use of MIG brazing over mechanical joining. In our industry, where we are increasingly asked to provide components with enhanced thermal and electrical properties, this technology has a real future. However, it requires a disciplined approach to process control and a thorough understanding of the metallurgy of the copper-steel interface. I recommend that any engineer considering this technology first conduct a series of experiments to determine the relationship between the welding parameters and the iron content in the copper deposit, and then use that information to set the process window. The paper provides a solid foundation for this work, and the practical lessons from the shop floor reinforce its conclusions.