ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Failure Analysis and Hardfacing Repair of Large Crankshaft Forging Dies

Literature Overview and Practical Context

The paper by Gao Wenliang, Liu Renpei, Liu Dashuang and Qiu Yue, published in Welding (2012, No. 8, pp. 63-66), addresses a chronic problem that every forging shop eventually faces: the premature failure of large crankshaft dies. The authors conducted a systematic failure analysis on dies from a specific forging plant and then performed hardfacing repair trials using two domestically produced flux-cored wires, RMD535 and RMD647. The study concludes that mechanical fatigue cracking and thermal wear are the primary failure modes, while thermal fatigue and plastic deformation act as accelerators rather than primary causes. The recommendation is to improve the die material's high-temperature strength, impact toughness and thermal stability at 650°C, and to apply composite hardfacing repair to extend die life.

From my own years running forging and pipe-manufacturing operations, I can tell you that die failure is not an abstract metallurgical problem—it is a direct cost driver. A large crankshaft die can cost hundreds of thousands of yuan, and every premature failure means lost production, re-machining, and potentially compromised forging quality. The fact that the authors found mechanical fatigue and thermal wear to be dominant aligns with what I have seen in heavy forging shops: the die cavity experiences cyclic compressive stresses at elevated temperature, and the surface undergoes abrasive wear from the hot metal flowing under high pressure. Thermal fatigue cracks, while present, are often secondary; they provide initiation sites for the mechanical fatigue cracks that eventually propagate and cause catastrophic die failure.

Failure Mechanism Analysis and Root Cause Determination

The failure analysis methodology used in this study is sound and follows the classic sequence of visual inspection, chemical composition verification, metallographic examination, hardness testing and scanning electron microscopy of fracture surfaces. The authors identified that the die material, likely a hot-work tool steel such as 5CrNiMo or H13, suffered from insufficient high-temperature strength and thermal stability. At 650°C, which is the typical surface temperature of a crankshaft die during forging, the material's yield strength drops significantly, and the cyclic loading leads to plastic deformation in the cavity surface. This deformation, combined with the thermal cycling, accelerates the initiation of fatigue cracks.

The key insight here is the interaction between thermal wear and fatigue. Thermal wear removes the hardened surface layer, exposing fresh material that is softer and more susceptible to plastic deformation. The deformed surface then acts as a stress raiser, promoting crack initiation. Once a crack initiates, it propagates under the cyclic forging load, eventually leading to gross failure. The authors correctly note that improving the die material's resistance to thermal wear and high-temperature fatigue is the most effective way to extend die life. This is not merely a material selection issue—it is also a heat treatment and surface engineering issue. In my experience, the best results come from a combination of a properly hardened and tempered die steel, a controlled forging temperature, and a robust surface treatment such as nitriding or hardfacing.

Hardfacing Repair Process and Consumable Selection

The hardfacing repair trials using RMD535 and RMD647 flux-cored wires represent a practical and cost-effective approach to extending die life. The composite hardfacing strategy—likely a buffer layer followed by a wear-resistant top layer—is a well-established technique in the industry. RMD535, which is probably a low-alloy or tool steel type wire, serves as the buffer layer to restore the die dimensions and provide a crack-resistant base. RMD647, likely a higher-alloyed wire with enhanced wear resistance, is then applied as the final layer to withstand the abrasive and thermal wear in the cavity.

The production validation results, which showed significant improvement in die life after repair, are the most important part of this study from a practical standpoint. However, I would caution that hardfacing repair of large dies is not a simple operation. The die must be preheated to a controlled temperature, typically 300-400°C for hot-work tool steels, to prevent cracking. The hardfacing process must be carefully controlled to minimize dilution with the base metal, which can reduce the wear resistance of the deposited layer. Post-weld heat treatment, such as tempering at 550-650°C, is essential to relieve residual stresses and restore the toughness of the heat-affected zone.

Engineering Practice Considerations and Lessons Learned

From a plant-floor perspective, this study highlights several critical points that are often overlooked. First, the failure analysis should be conducted on the actual failed die, not just on laboratory specimens. The service conditions—forging temperature, die temperature, lubrication, hammer or press characteristics—must be documented and correlated with the failure mode. Second, the choice of hardfacing consumables should be based on the specific failure mechanism. If thermal wear dominates, a carbide-rich hardfacing alloy is appropriate; if fatigue cracking dominates, a tougher, more ductile hardfacing alloy with lower hardness but higher impact toughness is preferred.

Third, the repair procedure must be validated through production trials, not just laboratory tests. The authors did this correctly by testing the repaired dies in actual production. Fourth, the economics of repair versus replacement must be evaluated. In many cases, a repaired die can achieve 60-80% of the life of a new die at a fraction of the cost, making repair a highly attractive option. However, if the die has suffered severe cracking or dimensional distortion, repair may not be economical.

I would also emphasize the importance of die maintenance and monitoring. Regular inspection of the die cavity for cracks, wear and dimensional changes can identify problems early and allow for timely repair. The use of dye penetrant testing or magnetic particle inspection after each forging campaign is a good practice. In my experience, a well-maintained die can be repaired two to three times before it must be scrapped, significantly reducing the overall tooling cost per forged part.

Key Insights and Recommendations

The study by Gao et al. provides a solid foundation for understanding crankshaft die failure and repair. The key takeaways are: mechanical fatigue and thermal wear are the dominant failure modes; improving high-temperature strength, toughness and thermal stability is the primary material strategy; and composite hardfacing with RMD535 and RMD647 is an effective repair method. For engineers in the forging industry, I would recommend the following practical actions:

  1. Conduct a thorough failure analysis on every prematurely failed die, documenting the failure mode and correlating it with service conditions.
  2. Evaluate the die material and heat treatment to ensure optimal high-temperature properties. Consider using premium grades such as H13 with improved cleanliness and isotropy.
  3. Implement a preventive maintenance schedule that includes regular inspection, surface condition monitoring and controlled repair procedures.
  4. Develop a hardfacing repair procedure that includes proper preheating, controlled interpass temperature, and post-weld tempering. Validate the procedure through production trials.
  5. Track the cost and life of repaired dies versus new dies to make informed economic decisions.

In conclusion, this paper is a valuable reference for anyone dealing with hot-work tool steel dies. The failure analysis methodology is rigorous, and the hardfacing repair approach is practical and proven. The lessons learned here can be applied not only to crankshaft dies but also to other hot-forging dies, extrusion dies and even to certain components in steel pipe manufacturing, such as piercing plugs and mandrel bars. The key is to understand the failure mechanism, select the right material and process, and maintain a disciplined approach to die management.