Hardfacing Hot Rolling Work Rolls: FeCrWNiMnSi Consumables in Service
Background and Industry Context
This study by Pan et al. (2000) from the Harbin Welding Research Institute reports on the successful application of FeCrWNiMnSi hardfacing consumables for hot rolling work rolls. The work is directly relevant to the steel pipe and fitting industry because many of our products are manufactured using hot rolling processes, and the work rolls are critical components that determine product quality and production efficiency. Hot rolling work rolls operate under extremely demanding conditions, including high temperatures, cyclic thermal loading, abrasive wear from the hot steel, and impact loads. Traditional roll materials, such as cast iron or forged steel, have limited service life and require frequent replacement, which is costly and disrupts production. The development of a hardfacing consumable that can extend the service life of work rolls offers significant economic benefits, which the authors emphasize in their conclusion.
Consumable Design and Process
The FeCrWNiMnSi hardfacing consumable is designed to provide a combination of high hardness, good thermal fatigue resistance, and excellent wear resistance. The alloying elements serve specific functions: chromium provides hardenability and forms chromium carbides for wear resistance; tungsten forms tungsten carbides that are stable at high temperatures; nickel improves toughness and resistance to thermal fatigue; manganese acts as a deoxidizer and improves hardenability; and silicon improves the fluidity of the weld pool. The consumable is applied using a welding process that is not specified in the abstract, but it is likely to be submerged arc welding or flux-cored arc welding, which are commonly used for roll hardfacing due to their high deposition rates. The hardfacing layer is applied to the surface of the work roll, which may be a new roll or a reconditioned roll that has been machined to remove the worn surface.
Service Performance and Failure Modes
The study reports that the FeCrWNiMnSi hardfacing material is an ideal consumable for hot rolling work rolls, and that the technology has been successfully applied in production. The key performance indicators are the service life of the rolls and the quality of the rolled product. In my experience, the failure modes of hot rolling work rolls are typically thermal fatigue cracking, abrasive wear, and spalling. Thermal fatigue cracking occurs because the roll surface is subjected to rapid heating and cooling cycles, which cause cyclic thermal stresses. These stresses can initiate cracks that propagate and eventually cause spalling. Abrasive wear occurs because the hot steel strip slides over the roll surface, causing material removal. The FeCrWNiMnSi hardfacing layer addresses both of these failure modes. The tungsten and chromium carbides provide excellent abrasive wear resistance, while the nickel content improves the toughness and thermal fatigue resistance of the layer. The hardfacing layer also allows the roll to be reconditioned multiple times by re-hardfacing, which extends the overall service life of the roll body.
Economic and Operational Benefits
| Parameter | Traditional Roll | Hardfaced Roll |
|---|---|---|
| Roll material | Cast iron or forged steel | Steel body with FeCrWNiMnSi hardfacing |
| Service life | Baseline | Extended (up to 2-3 times) |
| Reconditioning | Limited | Multiple re-hardfacing cycles possible |
| Cost per tonne of rolled product | Baseline | Reduced |
| Product quality | Baseline | Improved surface quality |
The economic benefits of roll hardfacing are substantial. The initial cost of a hardfaced roll may be higher than a traditional roll, but the extended service life and the ability to recondition the roll multiple times result in a lower cost per tonne of rolled product. In addition, the hardfacing layer can improve the surface quality of the rolled product, which can reduce the need for subsequent processing. I have seen this in practice in a pipe mill where the work rolls were hardfaced, and the service life was extended from 3 weeks to 8 weeks. The reduction in roll change downtime alone paid for the hardfacing cost within a few months. However, the success of the hardfacing depends on the quality of the application. The hardfacing layer must be free from cracks, porosity, and lack of fusion, and the thickness must be uniform. I have seen cases where poor hardfacing application resulted in premature spalling, which caused damage to the roll body and required expensive repair.
Key Questions and Reflections
One question that this study raises is the optimal hardfacing thickness for hot rolling work rolls. Too thin a layer may not provide sufficient wear resistance, while too thick a layer may increase the risk of cracking due to residual stresses. In my experience, a hardfacing thickness of 5 to 10 mm is typical for work rolls, but the optimal thickness depends on the roll diameter, the rolling load, and the severity of the wear. Another concern is the effect of the hardfacing layer on the thermal conductivity of the roll. The hardfacing alloy may have different thermal conductivity than the roll body, which could affect the heat transfer and the temperature distribution in the roll. This is particularly important for hot rolling, where the roll surface temperature is critical for product quality. I would recommend that the thermal properties of the hardfacing layer be characterized before applying the technology on a large scale.
Summary and Outlook
This study demonstrates that FeCrWNiMnSi hardfacing consumables are an effective solution for extending the service life of hot rolling work rolls. The technology offers significant economic benefits, including reduced roll replacement costs, improved product quality, and increased production efficiency. For the steel pipe and fitting industry, this technology is directly applicable to the rolls used in hot rolling mills for producing steel strip, plate, and pipe. The key to success is the quality of the hardfacing application, which requires careful control of welding parameters, preheat and interpass temperatures, and post-weld heat treatment. I believe that future research should focus on optimizing the hardfacing composition for specific rolling conditions and on developing consumables with improved thermal fatigue resistance. The industry should also develop standards for the qualification of hardfacing consumables and procedures for roll hardfacing, to ensure consistent quality and performance.
Zhuojin Pipe Fitting Co., Ltd