ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Ultrasonic Thickness Measurement Method for Stainless Steel Cladding on Hydrogenation Reactors

Background and Context

Hydrogenation reactors are the heart of any refinery upgrading unit, and the integrity of their stainless steel cladding is non-negotiable. The cladding, typically 309L or 347L austenitic stainless steel, is applied over a low-alloy steel base (such as 2.25Cr-1Mo or 3Cr-1Mo) to protect against hydrogen attack and high-temperature sulfidation. Over time, the cladding can be thinned by corrosion, erosion, or mechanical damage, and the ability to measure its remaining thickness accurately is critical for deciding whether to repair or replace the reactor. The paper by Zhang Tao et al. from the Shandong Special Equipment Inspection Institute addresses a practical problem: how to measure the cladding thickness with an ultrasonic thickness gauge when the base metal and the cladding have very different acoustic impedances and the interface is not always a clean, planar reflector.

Technical Challenges and Proposed Method

The fundamental challenge is that the acoustic impedance of austenitic stainless steel is close to that of the low-alloy steel base, so the reflection at the cladding-base interface is weak. Furthermore, the coarse, columnar grain structure of the austenitic weld overlay scatters the ultrasonic beam, causing high attenuation and noise. Conventional ultrasonic thickness gauges are designed to measure the time of flight to the first back-wall echo, which works well for homogeneous materials but fails when there are two distinct layers with a weak interface.

The authors propose a simple but effective method: use a dual-element transducer with a carefully selected frequency and focal length, and adjust the gain and the gate to capture the interface echo between the cladding and the base metal. The key is to differentiate the interface echo from the back-wall echo and from the noise caused by the grain boundaries. The paper presents measurement data from actual reactors and compares the ultrasonic readings with the design thickness, showing good agreement.

Parameter Recommended Setting Practical Notes
Transducer frequency 5 MHz (dual-element) Higher frequency improves resolution but increases attenuation
Focal length 10–15 mm Must be matched to the cladding thickness range
Gain Adjust to maximize interface echo Too high gain causes false readings from grain noise
Gate position Set to the interface echo Must be verified against a known thickness standard
Couplant Glycerin or high-viscosity gel Ensures good acoustic coupling on rough surfaces

Practical Implications for In-Service Inspection

In my experience, the measurement of cladding thickness is one of the most demanding NDT tasks on a refinery reactor. The surface is often rough, the cladding may have been repaired multiple times, and the interface can be irregular due to lack of fusion or incomplete penetration during the original cladding operation. The method described in this paper is a practical, shop-floor-friendly approach that does not require expensive phased-array equipment or complex signal processing. It is a classic example of using the right tool for the right job, with a competent operator who understands the metallurgy and the acoustic behavior of the materials.

I have personally seen cases where an inexperienced inspector misread the back-wall echo as the interface echo, leading to a gross overestimation of the cladding thickness and a false "pass" on a reactor that was actually critically thinned. The consequence of such an error is a potential catastrophic failure during the next operating cycle. The method in this paper, with its emphasis on verifying the gate and the gain against a known standard, is a direct countermeasure to this type of error.

Lessons Learned and Study Insights

The paper does not discuss the effect of the cladding-base interface condition on the measurement accuracy, which is a significant gap. In practice, the interface can be rough, wavy, or contain lack of fusion, all of which will scatter the beam and make the interface echo weak or ambiguous. I would recommend that the method be supplemented with a calibration block that simulates the actual interface condition, and that the inspector be trained to recognize the characteristic signal patterns of a degraded interface.

Another practical point is the need for a surface preparation. The cladding surface in a hydrogenation reactor is often covered with a thin layer of sulfide scale or coke, which can severely attenuate the ultrasonic beam. The paper does not mention this, but in the field, we always insist on grinding the surface to a smooth finish at the measurement points, even if it means taking the reactor out of service for a few extra hours.

Reference Value and Outlook

This paper is a useful, practical reference for any NDT engineer or inspector involved in the in-service inspection of hydrogenation reactors. The method is simple, repeatable, and cost-effective, and it can be implemented with standard ultrasonic equipment available in most inspection shops. The next step would be to develop a more sophisticated approach, such as using phased-array or time-of-flight diffraction techniques, to handle the more challenging cases where the interface is degraded or the cladding is thin. However, for the vast majority of routine inspections, the method described here is sufficient and reliable. The key is to have a well-trained operator who understands the limitations and the pitfalls of the technique.