Wire Stick-Out Length and Its Influence on Hardfacing Bead Geometry
Introduction to the Problem
The wire stick-out length, also known as the dry extension or electrode extension, is one of the most important parameters in any wire-fed welding process. It is the distance from the contact tip to the arc, and it directly influences the welding current, the arc voltage, and the heat input. In hardfacing applications, where the goal is to deposit a controlled layer of wear-resistant alloy on a component surface, the stick-out length has a significant effect on the shape and quality of the deposited bead.
The literature from Xinjiang University, published in 2018, presents a systematic study of the effect of wire stick-out length on the formation of hardfacing beads in three-dimensional welding. The study combines theoretical analysis, physical modeling, and experimental verification to provide a comprehensive understanding of the relationship between stick-out length and bead geometry.
This is a topic that I have seen cause problems on the shop floor many times. A welding operator who is not properly trained will often adjust the stick-out length to compensate for changes in the welding current or voltage, without understanding the fundamental relationship between these parameters. The result is a bead that is too wide, too narrow, too high, or too shallow, which can lead to poor fusion, lack of penetration, or excessive dilution of the hardfacing alloy.
Theoretical Analysis and Physical Modeling
The Relationship Between Stick-Out Length and Welding Current
The welding current in a wire-fed process is determined by the resistance of the wire between the contact tip and the arc. As the stick-out length increases, the resistance of the wire increases, which causes the welding current to decrease for a given voltage setting. This is because the wire acts as a resistor, and the voltage drop across the wire increases with its length.
The relationship between stick-out length and welding current can be expressed by the following equation.
| Parameter | Symbol | Relationship |
|---|---|---|
| Wire resistance per unit length | R | R = ρ / A, where ρ is the resistivity and A is the cross-sectional area |
| Total wire resistance | R_total | R_total = R × L, where L is the stick-out length |
| Welding current | I | I = (V - V_arc) / R_total, where V is the applied voltage and V_arc is the arc voltage |
This relationship means that as the stick-out length increases, the welding current decreases, which reduces the heat input and the melting rate of the wire. The result is a shallower penetration and a narrower bead, but with an increased reinforcement height because the wire is being deposited at a lower rate.
The Effect on Droplet Transfer
The stick-out length also affects the droplet transfer in the welding arc. When the stick-out length is increased, the electromagnetic force that promotes droplet detachment is reduced, which means that the droplets are larger and transfer less frequently. This can lead to an unstable arc and spatter, which degrades the quality of the hardfacing layer.
The literature identifies three main forces that affect droplet transfer.
| Force | Effect on Droplet Transfer | Influence of Stick-Out Length |
|---|---|---|
| Electromagnetic force | Promotes droplet detachment | Decreases with increasing stick-out length |
| Gravity force | Pulls the droplet downward | Independent of stick-out length |
| Surface tension force | Holds the droplet on the wire tip | Independent of stick-out length |
When the stick-out length is too long, the electromagnetic force is insufficient to detach the droplet, and the droplet grows until it is detached by gravity. This results in an irregular bead with spatter and poor fusion.
Experimental Findings and Analysis
The Experimental Setup
The Xinjiang University study used a three-dimensional welding system with a flux-cored wire for hardfacing. The stick-out length was varied from 10 mm to 30 mm, and the bead geometry was measured for each condition. The following table summarizes the experimental results.
| Stick-Out Length (mm) | Welding Current (A) | Bead Width (mm) | Bead Height (mm) | Penetration Depth (mm) | Spatter Level |
|---|---|---|---|---|---|
| 10 | 280 | 12.5 | 3.2 | 2.8 | Low |
| 15 | 265 | 11.8 | 3.5 | 2.5 | Low |
| 20 | 250 | 11.0 | 3.9 | 2.2 | Moderate |
| 25 | 235 | 10.2 | 4.3 | 1.9 | High |
| 30 | 220 | 9.5 | 4.8 | 1.6 | High |
The results show a clear trend. As the stick-out length increases from 10 mm to 30 mm, the welding current decreases from 280 A to 220 A, the bead width decreases from 12.5 mm to 9.5 mm, the bead height increases from 3.2 mm to 4.8 mm, and the penetration depth decreases from 2.8 mm to 1.6 mm. The spatter level increases from low to high.
Interpretation of the Results
The decrease in welding current with increasing stick-out length is consistent with the theoretical analysis. The wire resistance increases with length, which reduces the current for a given voltage setting. This reduction in current reduces the heat input, which reduces the penetration depth and the bead width.
The increase in bead height with increasing stick-out length is a result of the lower deposition rate. When the welding current is reduced, the wire melting rate decreases, which means that the wire is being fed into the arc at a rate that is higher than the melting rate. This causes the wire to protrude further into the arc, which increases the bead height.
The increase in spatter with increasing stick-out length is a result of the unstable droplet transfer. When the stick-out length is too long, the electromagnetic force is insufficient to detach the droplets, which causes them to grow until they are detached by gravity. This irregular droplet transfer causes spatter and poor bead quality.
The Practical Range for Hardfacing
The literature concludes that the optimal stick-out length for three-dimensional hardfacing is in the range of 10 to 15 mm. Within this range, the welding current is stable, the droplet transfer is regular, and the bead geometry is consistent. When the stick-out length exceeds 20 mm, the welding process becomes unstable, and the bead quality degrades.
Practical Implications for Shop Floor Control
Setting the Stick-Out Length
On the shop floor, the stick-out length is often set by the welding operator based on the length of the contact tip and the nozzle. However, the actual stick-out length can vary due to the following factors.
| Factor | Effect on Stick-Out Length | Practical Control |
|---|---|---|
| Contact tip wear | Increases the effective stick-out length | Replace the contact tip regularly |
| Nozzle position | Changes the distance from the nozzle to the workpiece | Adjust the nozzle position to maintain the correct stick-out |
| Wire feed speed | Affects the wire melting rate, which changes the stick-out | Set the wire feed speed based on the welding current |
| Workpiece geometry | Changes the distance from the contact tip to the workpiece | Use a jig or fixture to maintain a consistent distance |
The most common problem on the shop floor is contact tip wear. As the contact tip wears, the diameter of the bore increases, which allows the wire to move laterally and changes the effective stick-out length. This can cause the bead geometry to vary along the length of the weld, which is a common cause of defects in hardfaced components.
The Effect on Dilution
The stick-out length also affects the dilution of the hardfacing alloy with the base metal. When the penetration depth is reduced, the dilution is reduced, which means that the hardfacing layer has a higher concentration of the alloying elements. This can be beneficial if the hardfacing alloy is expensive, but it can also be detrimental if the dilution is too low and the fusion between the hardfacing layer and the base metal is inadequate.
The following table shows the relationship between stick-out length and dilution.
| Stick-Out Length (mm) | Penetration Depth (mm) | Dilution (%) | Fusion Quality |
|---|---|---|---|
| 10 | 2.8 | 18 | Good |
| 15 | 2.5 | 15 | Good |
| 20 | 2.2 | 12 | Acceptable |
| 25 | 1.9 | 9 | Poor |
| 30 | 1.6 | 6 | Poor |
When the stick-out length is too long, the dilution is too low, and the fusion between the hardfacing layer and the base metal may be inadequate. This can lead to delamination of the hardfacing layer during service.
Quality Control Considerations
From a quality control perspective, the stick-out length should be monitored and controlled to ensure consistent bead geometry. The following measures are recommended.
- Use a contact tip with a known bore diameter and replace it at regular intervals.
- Use a nozzle with a known position and adjust it to maintain the correct stick-out length.
- Set the wire feed speed based on the welding current and the wire diameter.
- Use a jig or fixture to maintain a consistent distance between the contact tip and the workpiece.
- Monitor the bead geometry during welding and adjust the stick-out length if necessary.
Key Takeaways and Conclusions
The Xinjiang University study provides a comprehensive understanding of the relationship between wire stick-out length and hardfacing bead geometry. The key findings are that increasing the stick-out length reduces the welding current, which reduces the bead width and penetration depth, while increasing the bead height and spatter level.
For practical hardfacing applications, the stick-out length should be maintained in the range of 10 to 15 mm. This range provides a stable welding process, regular droplet transfer, and consistent bead geometry. When the stick-out length exceeds 20 mm, the welding process becomes unstable, and the bead quality degrades.
From my own experience, I would emphasize that the stick-out length is one of the most important parameters in hardfacing, but it is also one of the most commonly overlooked. Welding operators often focus on the welding current and voltage, but they do not always understand that the stick-out length directly influences these parameters. Training the operators to understand the relationship between stick-out length and bead geometry is essential for producing high-quality hardfaced components.
Zhuojin Pipe Fitting Co., Ltd