ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Magnetic Field Control of Strip Electroslag Surfacing Layer Formation

Background and Why This Study Matters

Strip electroslag surfacing is a high-deposition process used extensively in the petrochemical and power generation industries for cladding pressure vessels and other large components. The process uses a wide strip electrode, typically 60 mm or 90 mm wide, and a flux that becomes molten and conducts electricity. The resistance heating of the molten flux melts the strip and the base material, creating a wide, smooth surfacing layer.

The problem that the authors addressed is one that I have encountered many times in my career: the magnetic contraction effect. When you have a high current flowing through a wide strip electrode, the parallel current elements attract each other, causing the molten pool to pinch in the middle. This results in severe undercutting at the edges of the strip, which is a major defect that can lead to lack of fusion and stress concentration.

The authors proposed using an external magnetic field to counteract the magnetic contraction effect. This is a clever solution that addresses the root cause of the problem. By applying a controlled external magnetic field, the Lorentz force can be used to counteract the pinch effect and produce a smooth, uniform surfacing layer.

The Problem and the Solution Principle

The magnetic contraction effect is a fundamental problem in strip electroslag surfacing. The high current flowing through the strip electrode creates a magnetic field around each current element. These magnetic fields interact, creating a force that attracts the current elements to each other. This causes the molten pool to contract in the middle, leading to undercutting at the edges.

The authors recognized that this effect could be counteracted by applying an external magnetic field. The Lorentz force, which is the force on a current-carrying conductor in a magnetic field, can be used to push the molten pool outward, counteracting the contraction.

The key to this approach is the direction and magnitude of the external magnetic field. The field must be oriented so that the Lorentz force acts in the direction opposite to the contraction. The authors developed a coil-based magnetic control device that could be adjusted to provide the correct field strength and orientation.

The experimental work involved varying the magnetic pole position, the magnetic control current, and the welding parameters to determine the optimal conditions for eliminating undercutting. This is a systematic approach that I would expect from a well-designed research program.

Experimental Results and Optimization

The authors tested several magnetic control configurations and developed a practical coil-based device. The results showed that the magnetic control could effectively eliminate the undercutting, but the effectiveness depended on the pole position, the magnetic control current, and the welding parameters.

The following table summarizes the key parameters and their effects:

Parameter Effect on Magnetic Control Optimal Range
Magnetic Pole Position Determines the direction and distribution of the magnetic field Centered on the strip electrode
Magnetic Control Current Determines the strength of the external magnetic field Sufficient to counteract the pinch effect
Welding Current Affects the magnitude of the pinch effect Standard range for strip electroslag
Welding Speed Affects the molten pool size and solidification rate Standard range for strip electroslag

The practical result was a significant reduction in undercutting, allowing for the production of high-quality surfacing layers with the high deposition rates that are characteristic of the strip electroslag process.

This is a significant achievement because it allows the use of higher welding currents, which increases the deposition rate without the associated defect of undercutting. In the petrochemical industry, where large pressure vessels require thick cladding, the deposition rate is a critical factor in the production schedule.

Shop-Floor Implementation and Practical Considerations

From a practical standpoint, the implementation of magnetic control in strip electroslag surfacing requires careful attention to the equipment design. The coil-based device must be robust enough to withstand the harsh environment of the welding shop, and it must be adjustable to allow for fine-tuning of the magnetic field.

The magnetic pole position is critical. If the poles are not correctly positioned, the magnetic field may not be uniform, and the Lorentz force may not be evenly distributed. This could lead to a non-uniform surfacing layer with some areas still showing undercutting.

The magnetic control current must be matched to the welding current. As the welding current increases, the pinch effect becomes stronger, requiring a higher magnetic control current to counteract it. This requires a control system that can automatically adjust the magnetic field based on the welding parameters.

I have seen many attempts to improve strip electroslag surfacing that focused on the flux composition or the strip material, but this study takes a different approach. By addressing the root cause of the problem, the magnetic contraction effect, the authors have provided a solution that can be applied to any strip electroslag surfacing operation.

Lessons Learned and Critical Questions

One of the key questions that this study raises is the long-term reliability of the magnetic control device. The coil-based device must be able to withstand the heat, magnetic fields, and mechanical vibrations of the welding environment. The insulation and cooling of the coil are critical factors that need to be addressed.

Another question is the effect of the magnetic field on the microstructure of the surfacing layer. The magnetic field can influence the solidification process, potentially affecting the grain structure and the mechanical properties of the deposited metal. This needs to be investigated to ensure that the magnetic control does not degrade the quality of the surfacing layer.

The authors also need to consider the effect of the magnetic field on the flux behavior. The molten flux is a conductor, and the magnetic field could influence its flow and distribution. This could affect the slag removal and the quality of the surfacing layer.

I would also question whether the magnetic control can be applied to other surfacing processes, such as strip submerged arc surfacing. The magnetic contraction effect is a fundamental problem in any process that uses a wide electrode, so the magnetic control approach could potentially be applied to other processes as well.

Study Insights and Implications for Practice

This study demonstrates a practical solution to a common problem in strip electroslag surfacing. The magnetic control approach addresses the root cause of the undercutting and provides a means to produce high-quality surfacing layers at high deposition rates.

The key insight is that the magnetic contraction effect can be counteracted by an external magnetic field. This is a fundamental principle that can be applied to any process that uses a wide electrode. The authors have developed a practical device that can be used in a production environment, which is a significant achievement.

For the shop floor, this means that strip electroslag surfacing can be used at higher welding currents, increasing the deposition rate and reducing the production time. This is particularly important for large components such as pressure vessels, where the cladding thickness can be significant.

Reference Value and Outlook

This study provides a valuable contribution to the field of strip electroslag surfacing. The magnetic control approach is a practical solution to a common problem, and the experimental results demonstrate its effectiveness.

Looking ahead, I would like to see more research on the optimization of the magnetic control parameters. The relationship between the magnetic field strength, the welding parameters, and the quality of the surfacing layer needs to be better understood.

I would also like to see the magnetic control approach applied to other surfacing processes. The principle is fundamental, and it could potentially be used to improve the quality of strip submerged arc surfacing and other processes that use wide electrodes.

The industry would also benefit from a standardization of the magnetic control equipment. A standardized design would allow for easier implementation and better reproducibility of the results.

In the end, this study is a good example of how a fundamental understanding of the physics of the welding process can lead to a practical solution to a common problem. The magnetic control approach is a significant contribution to the field, and I would encourage the industry to adopt it in production.