ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Hardness Distribution and Impact Toughness of Q345 Steel-Based Cladding Composite Plates

Background and Purpose

This study by Zhang Ziling and colleagues from Hunan University of Science and Technology and Gree Electric Appliances examines the hardness distribution and impact toughness of Q345 steel-based cladding composite plates produced by gas metal arc welding (GMAW) cladding. The authors used optical microscopy, Vickers hardness testing, impact testing, and scanning electron microscopy to characterize the microstructure, hardness, impact toughness, and fracture surfaces of the composite plates. The results show that the cladding composite plates have good appearance quality, no obvious welding defects, and a hardness distribution that increases from the base plate to the cladding layer. The impact toughness reaches 64 J/cm², and the fracture surfaces of normalized and quenched specimens show ductile and quasi-cleavage fracture modes.

This topic is directly relevant to the steel pipe and fitting industry because composite plates are used in applications where a high-strength or corrosion-resistant surface is required on a lower-cost base material. In pipe and fitting manufacturing, this concept is applied in the form of cladded pipes, bimetallic pipes, and weld-overlaid fittings. The economics are compelling: you get the performance of an expensive alloy at a fraction of the cost of a solid alloy component.

Technical Analysis of Microstructure and Properties

The paper describes the microstructure evolution from the base plate to the cladding layer. The base plate Q345 steel has a typical ferrite-pearlite microstructure, with blocky ferrite and banded pearlite. As you move into the cladding layer, the microstructure changes to granular ferrite and pearlite, and then to blocky ferrite and flocculent graphite at the surface. This transition reflects the different thermal histories and compositions of the base metal, the heat-affected zone, and the cladding deposit.

The hardness distribution shows a jump from the base plate to the cladding layer. This is expected, because the cladding alloy is typically a high-strength or hardfacing material. The paper reports that the hardness is relatively uniform within the cladding layer, which is a good sign. A uniform hardness distribution indicates a consistent deposit with no significant segregation or dilution variations.

The impact toughness of 64 J/cm² is a solid value for a cladding composite plate. It indicates that the cladding layer is not brittle and can absorb significant energy before fracture. The fracture surfaces show ductile fracture in the normalized specimens and quasi-cleavage fracture in the quenched specimens. This is consistent with the microstructures: normalized specimens have a more ductile ferrite-pearlite structure, while quenched specimens have a harder, less ductile martensitic or bainitic structure.

Property Base Plate (Q345) Cladding Layer Composite Plate
Microstructure Blocky ferrite + banded pearlite Granular ferrite + pearlite → blocky ferrite + flocculent graphite Graded microstructure
Hardness Lower Higher, uniform Step increase from base to cladding
Impact toughness Baseline 64 J/cm² Good, ductile fracture mode
Defect level N/A No obvious welding defects Good appearance quality

The key finding is that the composite plate achieves a good combination of hardness and impact toughness. This is important for applications where the component must withstand both abrasive wear and impact loading. The graded microstructure, from the ductile base plate to the hard cladding layer, provides a transition that prevents delamination and improves the overall performance of the composite.

Engineering Implications and Reflections

For those of us who manufacture cladded pipes and fittings, this study reinforces several important principles.

First, the quality of the cladding is determined by the process parameters and the filler material. The paper used GMAW cladding, which is a common and versatile process. The key parameters are the welding current, voltage, travel speed, and the composition of the filler wire. These parameters determine the dilution, the microstructure, and the properties of the cladding layer.

Second, the hardness distribution is a critical quality indicator. A step increase in hardness from the base plate to the cladding layer is expected, but the magnitude of the step and the uniformity of the cladding hardness are important. If the hardness step is too large, the transition zone may be susceptible to cracking under thermal or mechanical loading. If the cladding hardness is not uniform, it indicates inconsistent deposition or dilution.

Third, the impact toughness of the cladding layer is often overlooked. Many specifications focus on hardness and chemical composition, but impact toughness is equally important for components that are subjected to impact loading or thermal shock. The value of 64 J/cm² reported in this study is a good benchmark for a cladding composite plate.

In my experience, the most common problems with cladded components are:

The study by Zhang and colleagues addresses the first two problems by demonstrating that a properly designed cladding process can produce a composite plate with good hardness and impact toughness. The graded microstructure is the key: it provides a transition that prevents delamination and improves the overall performance.

For practical applications, I would recommend the following for cladded pipe and fitting manufacturing:

The study is a valuable contribution to the field of cladding composite materials. It demonstrates that a well-designed cladding process can produce a composite plate with a good combination of hardness and impact toughness, which is exactly what is needed for many industrial applications.

In summary, this paper provides a solid technical foundation for the production of cladding composite plates. The findings on microstructure evolution, hardness distribution, and impact toughness are directly applicable to the manufacturing of cladded pipes and fittings. The industry would benefit from incorporating these findings into cladding process qualification and quality control programs.