Composite Overlay Welding Repair of Ultra-High Manganese Steel Hammer Heads
Literature Overview and Technical Background
This 2005 paper from Jinan Iron and Steel Group addresses a problem I have seen on every crusher line I have ever walked: the catastrophic wear of ZGMn17 austenitic manganese steel hammer heads. The authors, Zhang Xiangfu and colleagues, set out to determine whether a worn hammer head could be brought back to service rather than scrapped. For a plant running a hammer crusher around the clock, this is not an academic question. A hammer head that costs several thousand yuan but fails after weeks of service represents a recurring capital drain, and the ability to repair it three or four times before it is truly spent changes the economics of the whole crushing circuit.
The material in question, ZGMn17, is a high-manganese austenitic steel with roughly 11 to 14 percent manganese and 1.0 to 1.4 percent carbon. Its remarkable toughness comes from its fully austenitic structure at room temperature, and its work-hardening ability means that every impact on the crushing surface actually strengthens the surface layer rather than wearing it away. This is the same metallurgical principle that makes Hadfield steel railway crossings and rock crusher jaws so durable. However, this very property makes the material notoriously difficult to weld. The heat-affected zone (HAZ) of a conventional weld on ZGMn17 will precipitate carbides at the grain boundaries when the temperature exceeds roughly 300 to 400 degrees Celsius, and those carbides destroy the material's toughness. The result is a brittle, crack-prone HAZ that fails in service long before the repair itself would wear out.
The authors correctly identify that any repair strategy must therefore avoid significant heat input into the base metal, or must use a buffer layer that can accommodate the thermal cycle without embrittling the substrate. Their chosen approach is a three-layer composite: the original ZGMn17 base, an intermediate transition layer deposited with H1Cr21Ni10Mn6 austenitic stainless steel filler wire, and a final wear-resistant hardfacing layer on top.
Interpretation of the Composite Repair Strategy
The genius of the composite approach lies in the properties of the transition layer. H1Cr21Ni10Mn6 is an austenitic stainless steel filler wire with approximately 21 percent chromium, 10 percent nickel, and 6 percent manganese. Its fully austenitic structure, high nickel content, and relatively high manganese content give it two critical advantages. First, it can absorb the dilution from the high-manganese base metal without forming brittle martensite or massive carbide networks at the fusion boundary. Second, it has excellent ductility and toughness, which means it can accommodate the thermal expansion mismatch between the base metal and the hardfacing layer without cracking.
The authors report that the transition layer must be deposited with low heat input, using small diameter electrodes and short arc length, to minimise the width of the heat-affected zone in the base metal. The weld beads should be peened immediately after deposition to relieve residual stresses, and interpass temperature must be kept below 150 degrees Celsius. This is a critical parameter. If the interpass temperature climbs too high, the base metal will begin to precipitate carbides and the repair will fail. I have seen this exact failure mode in a crusher rebuild where the welder ran continuous beads without any interpass control, and the hammer head cracked through the HAZ within days of returning to service.
The wear-resistant top layer is deposited after the transition layer is complete and has cooled. The authors do not specify the exact hardfacing alloy, but the principle is clear: the top layer must have high hardness and good impact resistance. For hammer crusher applications, a martensitic or carbide-rich hardfacing alloy in the range of 50 to 60 HRC is typically appropriate. The transition layer ensures that this hard, brittle top layer does not crack the base metal, and the base metal's work-hardening capability remains intact beneath the repair.
Process Parameters and Practical Considerations
The authors report successful repair of ZGMn17 hammer heads using this composite approach. Based on my own experience with similar repairs, I would emphasise the following process parameters as the practical envelope for this type of work.
| Parameter | Recommended Range | Practical Notes |
|---|---|---|
| Base metal temperature before welding | 20 to 50 °C | Never preheat ZGMn17; preheating accelerates carbide precipitation. |
| Interpass temperature | Below 150 °C | Use contact pyrometer or temperature-indicating crayons; forced air cooling between passes if necessary. |
| Transition layer electrode | H1Cr21Ni10Mn6, 3.2 mm diameter | Small diameter reduces heat input per pass. |
| Welding current | 90 to 120 A | Short arc, low current to minimise dilution and HAZ width. |
| Arc voltage | 20 to 24 V | Keep arc length short. |
| Polarity | DCEP (reverse) | Standard for covered electrodes. |
| Peening | Immediately after each pass | Pneumatic needle peening or hammer peening to relieve residual stress. |
| Post-weld cooling | Air cool, no accelerated cooling | Do not water quench; thermal shock will crack the HAZ. |
One detail that the paper does not emphasise but which I have learned the hard way is the importance of grinding out all cracked and work-hardened surface material before welding. The work-hardened layer on a used hammer head is extremely hard and can contain microcracks. If the welder deposits the transition layer directly onto this layer, the cracks will propagate into the weld metal and the repair will fail. The surface must be ground back to sound, soft base metal, and any visible cracks must be completely removed and verified by magnetic particle inspection before welding begins.
Integration with Engineering Practice and Lessons Learned
This paper is a good example of the kind of practical repair technology that keeps plants running without the capital cost of replacing worn components. In my experience, the composite overlay approach described here is the correct strategy for any high-manganese steel component that has suffered abrasive wear but has not cracked through the section. The key is discipline in execution. Every step must be followed: surface preparation, low heat input, interpass temperature control, peening, and proper cooling. If any step is skipped, the repair will fail, and the failure will be blamed on the welding process rather than on the operator's lack of discipline.
I have seen a variant of this repair used on crusher jaws and gyratory crusher mantles with similar success. The transition layer concept is particularly valuable when the base metal is a high-manganese steel and the hardfacing alloy is a high-chromium iron or a martensitic steel. Without the transition layer, the hardfacing will crack the base metal during cooling, and the entire repair will be wasted.
The economic case for this repair is compelling. A new hammer head might cost several thousand yuan, while the repair cost is typically 20 to 30 percent of that figure, plus the labour and downtime. For a plant with dozens of hammer heads in service, the savings over a year are substantial. However, I would caution that the repair is only worth doing if the hammer head has not suffered significant section loss or cracking through the body. If the head has cracked through, the repair cost approaches the replacement cost and the risk of failure in service increases dramatically.
Study Insights and Conclusions
This paper is a valuable contribution to the practical literature on hardfacing repair of high-manganese steel components. The authors have correctly identified the metallurgical challenges and proposed a sound solution. The composite approach of base metal plus transition layer plus wear layer is the standard practice in the industry, and this paper confirms its effectiveness for ZGMn17 hammer heads. The key technical insight is that the transition layer must be an austenitic stainless steel with sufficient nickel and manganese to tolerate dilution from the high-manganese base metal without forming brittle phases. The process parameters must be carefully controlled to minimise heat input and prevent carbide precipitation in the base metal HAZ.
For the practising engineer, the takeaway is clear: high-manganese steel can be repaired successfully, but only with the right filler metal, the right process parameters, and the right discipline. The repair is economically attractive and technically sound when executed correctly. I would recommend this paper to any engineer responsible for crushing equipment maintenance, and I would encourage them to develop a written repair procedure based on these principles, with specific process parameters and inspection requirements, before attempting a repair on a critical component.
Zhuojin Pipe Fitting Co., Ltd