ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Research on Plasma Arc Powder Overlay Welding Equipment for Rolls

Literature Overview and Technical Background

This 2011 paper from Southwest Jiaotong University addresses a specific but important equipment problem: the design and construction of a plasma arc powder overlay welding machine for the repair of rolls. The authors, Yang Haibo and colleagues, describe the development of a machine that uses plasma arc welding with powdered filler material to deposit a wear-resistant layer on the surface of a roll. The paper focuses on the control system, the hardware architecture, and the programming logic, with particular emphasis on the use of a servo system for the torch oscillation and positioning.

The context is the repair of rolls used in steel mills and other heavy industries. Rolls are expensive components, and they wear out in service due to the abrasive and thermal loads they experience. The traditional repair method is to machine the worn roll down to sound metal and then deposit a new wear-resistant layer by welding. Plasma arc powder welding is particularly well suited to this application because it offers a high deposition rate, good control of the deposit thickness and composition, and a relatively low heat input, which minimises distortion of the roll.

The authors' contribution is to design and build a complete welding machine that can perform this repair reliably and efficiently. The machine is based on a PLC (programmable logic controller) as the central control unit, with a touch screen interface for setting and monitoring welding parameters. The torch oscillation system uses a servo drive instead of a conventional stepper drive, which provides faster and more precise positioning and oscillation. The paper describes the hardware architecture, the control logic, and the programming flow in detail.

Interpretation of the Equipment Design and Control System

The design of the machine is a classic example of a mechatronic system for welding automation. The PLC is the heart of the system, responsible for coordinating all the functions of the machine, including the movement of the torch, the feeding of the powder, the control of the plasma arc, and the monitoring of the welding parameters. The touch screen provides a user-friendly interface for the operator to set the welding parameters, such as welding current, arc voltage, travel speed, powder feed rate, and torch oscillation frequency and amplitude.

The use of a servo system for the torch oscillation is a key design decision. In a conventional stepper drive, the motor moves in discrete steps, which can cause vibration and imprecise positioning. A servo system, on the other hand, provides continuous, precise control of the torch position and speed, which is essential for achieving a uniform deposit thickness and a consistent weld bead profile. The authors report that the servo system provides faster oscillation and more precise positioning, which improves the quality of the deposit.

The control program is designed to coordinate all the functions of the machine in a logical sequence. The program starts with a set of initialisation steps, in which the machine checks its own status and confirms that all the subsystems are ready. It then enters a waiting state, in which it monitors the touch screen for operator input. When the operator initiates a welding cycle, the program starts the plasma arc, begins the powder feed, and starts the torch movement. The program continuously monitors the welding parameters and displays them on the touch screen in real time. If any parameter goes out of the set range, the program takes corrective action, such as adjusting the welding current or stopping the welding cycle.

The paper also describes the hardware architecture in some detail. The machine consists of several subsystems, including the plasma torch, the powder feeder, the welding power source, the motion system, and the control system. The plasma torch is the most critical component, as it must provide a stable, focused plasma arc that can melt the powder and deposit it on the roll surface. The powder feeder must deliver a consistent, controlled flow of powder to the torch, and the motion system must move the torch along the roll surface at a precise speed and with a precise oscillation pattern.

Process Parameters and Practical Considerations

Based on the authors' description and my own experience with plasma arc powder welding, I would summarise the practical process parameters for this type of equipment as follows.

Parameter Typical Range Practical Notes
Welding current 150 to 400 A Higher current increases deposition rate but also increases heat input.
Arc voltage 25 to 40 V Depends on torch design and plasma gas flow.
Plasma gas flow 2 to 5 L/min Argon is typically used as the plasma gas.
Shielding gas flow 10 to 20 L/min Argon or argon-helium mixture to protect the weld pool.
Powder feed rate 20 to 80 g/min Must be matched to the welding current and travel speed.
Travel speed 5 to 20 cm/min Slower speed increases deposit thickness.
Torch oscillation frequency 1 to 5 Hz Determines the bead width and the uniformity of the deposit.
Torch oscillation amplitude 5 to 20 mm Must be matched to the desired bead width.
Deposit thickness 2 to 10 mm per pass Multiple passes may be required for thicker deposits.

One of the most critical practical considerations is the alignment of the torch with the roll surface. The torch must be positioned at the correct angle and distance from the roll surface to achieve the desired deposit geometry and to avoid defects such as lack of fusion or porosity. The torch angle is typically 90 degrees to the roll surface, but it can be adjusted to optimise the deposit shape. The torch standoff distance is typically 5 to 10 mm, and it must be maintained accurately throughout the welding process.

Another critical practical consideration is the control of the powder feed rate. The powder must be delivered to the torch at a consistent rate, and the feed rate must be matched to the welding current and travel speed to achieve the desired deposit thickness and composition. If the powder feed rate is too high, the powder will not be fully melted and will be trapped in the deposit as inclusions. If the feed rate is too low, the deposit will be too thin and may not provide the required wear resistance.

The authors' use of a servo system for the torch oscillation is a significant improvement over the conventional stepper drive. The servo system provides faster and more precise oscillation, which allows the torch to cover a wider area in a shorter time and with a more uniform deposit. This is particularly important for the repair of large rolls, where the welding time can be significant and the uniformity of the deposit is critical.

Integration with Engineering Practice and Lessons Learned

This paper is a good example of the kind of equipment development that is necessary to bring a laboratory process to the shop floor. The authors have designed and built a complete welding machine that can perform plasma arc powder welding on rolls, and they have demonstrated that the machine can produce high-quality deposits. The use of a PLC as the control core and a servo system for the torch oscillation are both sound design decisions that improve the reliability and quality of the machine.

In my experience, the most common problem with plasma arc powder welding equipment is the stability of the powder feed. The powder must be delivered to the torch at a consistent rate, and any variation in the feed rate will cause variations in the deposit thickness and composition. The powder feeder must be designed to handle the specific powder being used, and it must be calibrated regularly to ensure that the feed rate is accurate. The authors' use of a PLC to control the powder feeder is a good approach, but the feeder itself must be of high quality and must be maintained properly.

Another common problem is the stability of the plasma arc. The plasma arc is sensitive to variations in the plasma gas flow, the welding current, and the torch standoff distance. If any of these parameters vary, the arc will become unstable, and the deposit quality will degrade. The PLC control system must be able to monitor these parameters and take corrective action if they go out of range. The authors' system appears to have this capability, which is a significant advantage.

The economic case for this equipment is clear. The cost of repairing a roll by plasma arc powder welding is typically 30 to 50 percent of the cost of a new roll, and the repair can be completed in a fraction of the time required to obtain a replacement. For a steel mill that operates continuously, the ability to repair rolls quickly and reliably is of great value. The equipment described in this paper is a significant step towards making this repair process practical and reliable.

Study Insights and Conclusions

This paper is a valuable contribution to the practical literature on welding equipment design. The authors have described the design and construction of a complete plasma arc powder welding machine for roll repair, with a particular focus on the control system and the use of a servo system for the torch oscillation. The machine is well designed and should be capable of producing high-quality deposits.

For the practising engineer, the key insight is that the design of the welding equipment is as important as the welding process itself. A well-designed machine can make the difference between a reliable, high-quality repair and a process that is plagued by defects and downtime. The authors' use of a PLC as the control core and a servo system for the torch oscillation are both sound design decisions that improve the reliability and quality of the machine. I would recommend this paper to anyone involved in the design or operation of welding equipment for roll repair, and I would encourage them to consider the lessons learned in this paper when developing their own equipment.