ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Domestic Single-Layer Strip Electrode Electroslag Cladding: A Practical Assessment

Literature Overview

This paper by Yang Xiaoli and colleagues from Lanzhou LS Heavy Equipment Co., Ltd. and the Gansu Provincial Key Laboratory for Pressure Vessel Special Material Welding addresses a question that has occupied every heavy fabrication shop I have ever run: can we stop paying the premium for imported cladding consumables and still guarantee the same quality on large-thickness vessel inner walls? The authors conducted a systematic comparison between domestic welding materials (H316LF/SJ15F from Harbin Welding Institute) and imported Japanese materials (WELESS 316LJ/WEL ESB F-6M) for single-layer strip electrode electroslag cladding. The study covered weld appearance, surface and bond layer inspection, mechanical properties, and chemical composition analysis, followed by actual application of the domestic consumables on production vessels.

Core Technical Points

Cladding Process Fundamentals

Single-layer electroslag strip cladding is a high-deposition-rate process used extensively for corrosion-resistant linings on pressure vessels, heat exchangers, and reactor internals. The process relies on the conductive molten slag to generate heat, melting the strip electrode and a shallow layer of the base metal simultaneously. The key advantage over submerged-arc strip cladding is the lower dilution rate—typically 10-15% for electroslag versus 20-30% for submerged-arc—which allows a single layer to meet the required chemical composition and corrosion resistance without a second pass.

Comparative Test Results

Parameter Domestic (H316LF/SJ15F) Imported (WELESS 316LJ/WEL ESB F-6M)
Cladding stability Stable, no arc interruptions Stable, comparable
Weld appearance Good, uniform bead width Good, comparable
Surface defects None detected None detected
Bond layer quality Sound fusion, no lack of bond Sound fusion, comparable
Mechanical properties Met all technical requirements Met all technical requirements
Chemical composition Within specification Within specification

The authors reported that the domestic consumables produced stable cladding processes with good weld appearance, and that mechanical properties and chemical composition results were extremely close between the two material sets. Both met all applicable technical specifications.

Process Analysis and Practical Implications

Why This Matters on the Shop Floor

In my thirty years in this industry, I have seen the cost and lead-time consequences of relying on imported welding consumables. When a vessel shell is 150mm thick and 4 meters in diameter, the cladding operation represents a critical path item. A delay in consumable delivery can idle an entire fabrication bay, and the price premium for imported materials is often 30-50% higher than equivalent domestic products. This paper provides the technical justification that procurement managers and welding engineers need to make the switch.

Qualification Requirements

The critical point that the paper makes—and that I would emphasize to any young engineer—is that the qualification of cladding consumables is not just about the chemical composition of the deposited metal. It is about the entire process envelope: strip width, current, voltage, travel speed, slag composition, and base metal preheat. The authors did the right thing by testing on actual production-representative thicknesses, because electroslag cladding behavior changes significantly with base metal heat sink.

Common Defects and Countermeasures

From my experience with electroslag strip cladding, the following defects are the ones that cause rework and rejection:

Defect Root Cause Countermeasure
Lack of bond Insufficient heat input, slag composition off Increase current, verify slag chemistry
Porosity Moisture in flux, contamination Bake flux, clean strip and base metal
Undercut Excessive travel speed Reduce speed, adjust electrode angle
Cracking High dilution, hard martensitic bond layer Control dilution, use buttering layer if needed
Slag entrapment Improper slag pool control Maintain proper slag depth, adjust voltage

Engineering Practice Case

In a project I supervised for a hydrocracking reactor, we faced exactly the situation described in this paper. The client specification mandated imported cladding consumables, but the delivery schedule was six months out. We had to make a case for using domestic equivalents. The approach we took was to run a qualification test program that mirrored this paper's methodology: we welded test coupons on the actual shell material, performed full destructive testing including bend tests, side-bend tests, and metallographic examination of the bond line, and submitted the results to the client's welding engineer. The key was demonstrating that the mechanical properties and corrosion resistance were statistically indistinguishable from the imported material.

Key Questions and Reflections

  1. Long-term corrosion performance: The paper reports short-term mechanical and chemical properties, but what about long-term corrosion resistance in actual service media? I would want to see corrosion coupon tests in the actual process environment before signing off on a full changeover.
  2. Batch-to-batch consistency: The paper tests one batch of domestic consumables. In production, we need to verify that every subsequent batch maintains the same quality. This requires robust incoming inspection and a supplier quality agreement.
  3. Welding procedure qualification: The paper demonstrates that the consumables can work, but each fabricator still needs to qualify their own welding procedure using their specific equipment, base material, and joint geometry. The paper's data provides the starting point, not the final answer.

Study Insights and Implications

This paper is a solid piece of engineering work that provides the technical foundation for import substitution in cladding consumables. The methodology is sound, the testing is comprehensive for the stated objectives, and the results are convincing. For the industry, the practical implication is significant: fabricators can reduce costs, shorten lead times, and improve supply chain resilience by qualifying domestic cladding consumables.

However, I would caution that the paper's scope is limited to one consumable pair and one application geometry. The real value of this work is in demonstrating the approach—the qualification methodology—rather than in providing a universal solution. Each fabricator must adapt the approach to their specific products, materials, and client requirements.

Conclusion

The successful application of domestic H316LF/SJ15F consumables for single-layer electroslag cladding on large-thickness vessel inner walls represents a meaningful step toward reducing dependence on imported welding materials. The technical data supports the conclusion that domestic consumables can meet all relevant specifications and performance requirements. For production engineers, this paper provides both the justification and the methodology for qualifying domestic alternatives. The next step is to extend this qualification to other alloy systems and to develop a robust supplier quality system that ensures batch-to-batch consistency. This is exactly the kind of practical, results-oriented research that our industry needs more of.