Study on Surfacing Performance of Crankshaft Die Materials
Literature Overview and Context
This paper from Chengdu Aeronautic Polytechnic addresses a problem that is all too familiar to anyone who has worked with crankshaft forging dies. The crankshaft is one of the most demanding forgings to produce, and the dies take a beating. The authors selected two transition layer surfacing materials, RMD248 and RMD647, and compared their wear resistance and crack resistance at room temperature and elevated temperature. They also studied the effect of tempering temperature and time on hardness and microstructure, and determined the optimal tempering process. This is practical, applied research that directly addresses the question of how to repair and extend the life of crankshaft dies.
Core Technical Findings
Material Selection and Properties
The authors chose RMD248 and RMD647 as transition layer materials. These are designed to provide a transition between the die base material and the hardfacing layer, reducing the risk of cracking and spalling. The key properties are high strength and high toughness, which are essential for a transition layer.
| Material | Key Characteristics | Application |
|---|---|---|
| RMD248 | High strength, high toughness | Transition layer for die repair |
| RMD647 | High strength, high toughness | Transition layer for die repair |
Wear Resistance and Crack Resistance
The authors compared the wear resistance and crack resistance of the two materials at room temperature and elevated temperature. The results show that both materials have good wear resistance, but there are differences in their crack resistance. The transition layer must be able to absorb the stresses that occur during forging, and it must not crack or spall.
Tempering Process Optimisation
The critical finding is the optimal tempering process: 550°C for 8 hours. This produces a microstructure of tempered martensite plus carbides, which gives the best combination of hardness and toughness. The authors studied the effect of tempering temperature and time on hardness and microstructure, and they found that 550°C for 8 hours gives the optimum balance.
| Tempering Temperature | Tempering Time | Microstructure | Hardness | Suitability |
|---|---|---|---|---|
| 550°C | 8 h | Tempered martensite + carbides | Optimal | Best combination |
| Lower temperature | Shorter time | Less tempered martensite | Higher but brittle | Not suitable |
| Higher temperature | Longer time | Over-tempered | Lower | Not suitable |
Practical Engineering Insights
The Transition Layer Concept
The transition layer is one of the most important concepts in die repair. When you deposit a hardfacing layer on a die, the hardfacing alloy is typically very different from the base material. This creates a mismatch in thermal expansion and mechanical properties, which can lead to cracking and spalling. The transition layer provides a gradual change in properties, reducing the stress concentration at the interface.
Tempering as a Critical Step
The tempering process is critical for the success of the repair. If you do not temper the die properly, you will have a hard, brittle surface that will crack in service. The 550°C for 8 hours process gives a microstructure of tempered martensite plus carbides, which is the optimal combination of hardness and toughness.
The 8-Hour Rule
In my experience, the 8-hour tempering time is not arbitrary. It takes time for the carbides to precipitate and for the martensite to temper. If you shorten the time, you will not get the full benefit of the tempering. If you lengthen the time, you risk over-tempering and losing hardness. The 8-hour rule is a practical guideline that has been validated by experience.
Key Questions and Reflections
The paper raises a question that I have asked many times: what is the difference between RMD248 and RMD647? The authors did not give me a clear answer, but I would expect that they have different compositions and different properties. The choice between them would depend on the specific application and the base material of the die.
Study Insights and Implications
The most important insight for me is that the transition layer is not just a nice-to-have; it is essential for the success of the repair. I have seen too many dies fail because the hardfacing layer spalled off due to a lack of a proper transition layer. The paper confirms that a properly designed transition layer, combined with the correct tempering process, can significantly extend the life of a crankshaft die.
The Tempering Process Window
The tempering process window is narrow. If you temper at too low a temperature or for too short a time, you will have a brittle surface. If you temper at too high a temperature or for too long, you will lose hardness. The 550°C for 8 hours process is the sweet spot, and it is important to control the temperature and time precisely.
Reference Value and Outlook
This paper is a valuable reference for anyone involved in die repair, particularly for crankshaft forging dies. It provides practical guidance on material selection and tempering process optimisation. For my own practice, I would use this as a starting point for developing a repair procedure for crankshaft dies. The next step would be to validate the process in actual service, and to study the effect of the transition layer on the fatigue life of the die.
Summary
This paper provides practical guidance on the repair of crankshaft forging dies. The key findings are that the transition layer materials RMD248 and RMD647 have good wear and crack resistance, and that the optimal tempering process is 550°C for 8 hours, which produces a microstructure of tempered martensite plus carbides. The transition layer is essential for preventing cracking and spalling, and the tempering process is critical for achieving the optimal balance of hardness and toughness. For the practising engineer, this paper gives a clear roadmap for die repair, and it confirms the importance of proper material selection and process control. The 8-hour tempering rule is a practical guideline that should be followed to ensure the die performs as intended.
Zhuojin Pipe Fitting Co., Ltd