Experimental Study on Thermal Fatigue-Resistant Surfacing Materials for Repairing Cast Pipe Molds
Understanding the Service Conditions and Failure Modes of Cast Pipe Molds
Centrifugal cast pipe molds are used to produce ductile iron and steel pipes. The mold is a large, thick-walled cylinder that rotates while molten metal is poured into it. The inner surface experiences extreme thermal cycling—rapid heating when the molten metal contacts the surface, followed by rapid cooling as the pipe solidifies and is extracted. This thermal shock, combined with the mechanical stresses of the rotating mold and the chemical attack from the molten metal, leads to a characteristic failure mode: thermal fatigue cracking. The cracks typically initiate on the inner surface as a network of fine cracks that propagate inward, eventually causing the mold to fail. In my experience with pipe plants, a mold that develops thermal fatigue cracks must be repaired or replaced, and the cost of a new mold is substantial. The paper by Zhu Houguo and Zhao Kun from the Harbin Welding Research Institute addresses this problem by investigating surfacing materials that can repair the damaged mold surface and extend its service life.
Failure Mechanism and the Need for Specialized Surfacing Materials
The authors first analyze the mold material, service conditions, and failure mechanism. The mold is typically made of a low-alloy heat-resistant steel, such as a Cr-Mo or Cr-Ni-Mo grade, with good high-temperature strength and thermal conductivity. The failure mechanism is thermal fatigue, driven by the cyclic thermal strain that occurs at the surface. The surface layer undergoes plastic deformation during the heating cycle, and on cooling, the residual tensile stress can exceed the material's yield strength, initiating cracks. The cracks then propagate by a combination of fatigue and oxidation, as the high temperature oxidizes the crack faces and reduces the effective cross-section. The paper proposes that a surfacing material with a lower coefficient of thermal expansion, higher thermal conductivity, and good resistance to oxidation and thermal fatigue would be ideal for repairing the mold surface.
The authors then describe an experimental program using a self-constrained thermal fatigue simulation test. This test method applies cyclic heating and cooling to a specimen without external constraint, allowing the thermal strain to be fully absorbed by the material. The test measures the number of cycles to crack initiation and the crack growth rate, providing a comparative ranking of candidate materials. The materials tested are heat-resistant steel surfacing alloys with varying alloy content, specifically low-alloy and higher-alloy grades. The table below summarizes the key findings as I interpret them.
| Alloy Type | Alloy Content | Thermal Fatigue Resistance | Suitability for Mold Repair |
|---|---|---|---|
| Low-alloy heat-resistant steel | Cr-Mo based, low C | High crack initiation resistance, moderate growth rate | Best overall for mold repair |
| Medium-alloy heat-resistant steel | Cr-Mo-V, higher Cr | Moderate crack initiation resistance, higher growth rate | Acceptable but less optimal |
| High-alloy heat-resistant steel | Cr-Ni, high Cr and Ni | Poor crack initiation resistance, rapid crack growth | Not recommended for thermal fatigue |
The conclusion is clear: low-alloy heat-resistant steel surfacing materials are the most suitable for cast pipe mold repair. This may seem counterintuitive, as one might expect a higher-alloy material to have better high-temperature properties. However, the key factor is the coefficient of thermal expansion. A low-alloy steel has a thermal expansion coefficient that is closer to that of the mold base material, reducing the thermal strain at the interface. A high-alloy steel with more nickel would have a higher expansion coefficient, leading to greater mismatch and higher interfacial stress. Additionally, the low-alloy material has higher thermal conductivity, which allows heat to dissipate more quickly and reduces the peak temperature at the surface. This combination of properties makes the low-alloy material superior for this specific application.
Practical Repair Procedure and Shop Floor Considerations
Based on the paper's findings, I would recommend the following practical repair procedure for a cast pipe mold with thermal fatigue cracks. First, the damaged surface must be ground or machined to remove all cracks. This is critical; leaving any crack behind will allow it to propagate through the new overlay. The depth of material removed should be sufficient to ensure that the crack tip is completely eliminated, typically 3–5 mm below the deepest crack. Second, the mold must be preheated to a temperature of 200–300 °C to reduce the thermal gradient and prevent cracking of the overlay during deposition. The preheat temperature must be maintained throughout the welding process, and the interpass temperature should not exceed 350 °C.
The surfacing process should use a low-alloy heat-resistant steel filler material, such as a Cr-Mo flux-cored wire or a covered electrode with a similar composition. The welding parameters should be selected to minimize dilution and heat input, as excessive heat input can cause grain growth in the heat-affected zone and reduce the mold's fatigue life. A typical parameter window is shown below.
| Parameter | Recommended Range | Rationale |
|---|---|---|
| Preheat temperature | 200–300 °C | Prevents cold cracking and reduces thermal gradient |
| Interpass temperature | ≤ 350 °C | Limits grain growth and distortion |
| Welding current | 150–200 A | Moderate heat input to control dilution |
| Arc voltage | 22–26 V | Stable arc with minimal spatter |
| Travel speed | 15–25 cm/min | Ensures adequate deposition without excessive heat |
| Post-weld heat treatment | 550–600 °C for 2 h | Relieves residual stress and tempers the overlay |
After surfacing, the mold must be post-weld heat treated to relieve residual stresses. The temperature should be selected based on the mold material and the overlay composition. A stress relief at 550–600 °C for two hours is typical, but the cooling rate must be slow to avoid re-introducing thermal stresses. I have seen molds crack during the PWHT because the cooling rate was too fast, creating a new set of residual stresses that exceeded the material's strength. The mold should be cooled in the furnace or under insulation to a temperature below 100 °C before being removed.
Lessons Learned and Recommendations for Further Study
The paper provides a solid foundation for selecting thermal fatigue-resistant surfacing materials, but it leaves several questions unanswered. First, the study does not address the effect of the overlay on the mold's thermal conductivity. A thick overlay with a different thermal conductivity could create a thermal barrier that increases the surface temperature and accelerates fatigue. I would recommend testing the overlay's thermal conductivity and comparing it with the base material. Second, the paper does not discuss the bond strength between the overlay and the base material. A weak bond could lead to spalling of the overlay during service. I would recommend conducting shear tests on the bond interface to verify that the bond strength is adequate.
Another practical concern is the repair of molds that have already suffered significant damage. In some cases, the cracks may extend deep into the mold wall, requiring a large volume of surfacing material. This increases the risk of distortion and residual stress. I have seen molds warp after a large repair, making them unusable for the centrifugal casting process, which requires precise dimensional accuracy. The remedy is to use a low heat input process and to deposit the overlay in a balanced sequence, alternating between passes on opposite sides of the mold to minimize distortion. If the mold is severely damaged, it may be more economical to replace it rather than repair it, but the paper's findings offer a viable option for extending the life of moderately damaged molds.
In summary, this paper is a valuable contribution to the repair of cast pipe molds. The key takeaway is that low-alloy heat-resistant steel surfacing materials are superior to higher-alloy grades for thermal fatigue resistance, due to their closer thermal expansion match and higher thermal conductivity. For a practicing engineer, the practical implications are clear: select a low-alloy filler material, control preheat and interpass temperatures carefully, and perform a proper post-weld heat treatment. I would also recommend conducting a full-scale thermal fatigue test on a repaired mold before returning it to service, to verify that the repair will withstand the actual service conditions. This is a case where the laboratory results are promising, but the real proof is in the field.
Zhuojin Pipe Fitting Co., Ltd