Cracking Failure Analysis of Support Roll Surface Cladding Layers: A Metallurgical and Mechanical Investigation
Literature Overview and Practical Significance
This paper by Wang Hui and colleagues from Dalian Huarui Heavy Industry and Dalian Maritime University presents a detailed failure analysis of cracks that appeared in the surface cladding layer of a large support roll. The roll is used in heavy industrial equipment, and the cracks were observed both on the surface and within the cladding layer. The authors conducted a thorough investigation using macroscopic and microscopic examination, including scanning electron microscopy and energy-dispersive X-ray spectroscopy, to identify the root cause.
This is a classic failure analysis case, and the paper provides a valuable lesson for our industry. Support rolls are critical components in steel mills, and their failure can cause significant production losses. The paper identifies two types of cracks: crystallisation hot cracks and reheat cracks. It also identifies the material factors and the mechanical factors that contributed to the failure. This is exactly the kind of analysis that we need to perform when we encounter cracking in cladded components.
Interpretation of Technical Points
Crystallisation Hot Cracks and Reheat Cracks
The paper distinguishes between two types of cracks. Crystallisation hot cracks form during the solidification of the weld metal, when the liquid film between the dendrites is still present. These cracks are typically intergranular and have a dendritic morphology. Reheat cracks, also known as stress-relief cracks, form during post-weld heat treatment or during service at elevated temperatures, when the residual stresses are relieved and the material has low ductility in the temperature range of 400-600°C. The paper correctly identifies both types in the failed roll.
Material Factors: Phosphorus, Sulphur, and Carbide-Forming Elements
The authors found that the cladding material contained a high phosphorus content, and that the grain boundaries were enriched with carbide-forming elements such as chromium, manganese, and vanadium, as well as the impurity elements phosphorus and sulphur. These are the classic material factors for both hot cracking and reheat cracking.
Phosphorus and sulphur are well-known impurities that segregate to grain boundaries and reduce the solidus temperature, making the material more susceptible to hot cracking. The carbide-forming elements, on the other hand, can precipitate as carbides at the grain boundaries during the reheat cycle, causing the material to lose ductility and become susceptible to reheat cracking. The paper's identification of these factors is consistent with our experience in the field.
Mechanical Factors: Bending Load from the Roll's Own Weight
The paper also identifies a mechanical factor: the bending load caused by the roll's own weight. A large support roll is a massive component, and its weight can create significant bending stresses, especially when it is supported at two points. These stresses, combined with the residual stresses from the cladding process, can exceed the strength of the cladding layer and cause cracking. This is a crucial insight, as it reminds us that the mechanical design of the component must be considered in conjunction with the metallurgical properties of the cladding.
Integration with Engineering Practice
In our industry, we encounter similar cracking issues in cladded rolls, shafts, and other large components. The lessons from this paper are directly applicable. First, we must control the impurity content of the cladding consumables. Phosphorus and sulphur levels should be kept as low as possible, especially for high-strength or high-hardness cladding alloys. Second, we must carefully select the cladding alloy to match the service conditions. If the component will be subjected to elevated temperatures, we need an alloy that is resistant to reheat cracking. Third, we must consider the mechanical design of the component, including the support conditions and the expected service loads.
The paper also highlights the importance of post-weld heat treatment. In many cases, reheat cracking can be avoided by using a proper PWHT cycle that allows the residual stresses to be relieved without causing the material to lose ductility. The PWHT temperature and time must be carefully selected based on the material composition and the thickness of the cladding.
Key Questions and Reflections
One question that the paper raises is whether the cracks were present immediately after cladding or whether they developed during service. The authors suggest that the crystallisation hot cracks may have formed during the cladding process, while the reheat cracks may have formed during PWHT or during service. This distinction is important, as it affects the corrective action. If the hot cracks were present after cladding, then the welding parameters or the consumables need to be changed. If the reheat cracks formed during PWHT, then the PWHT cycle needs to be revised.
Another reflection concerns the role of the substrate. The paper focuses on the cladding layer, but the substrate material and its condition also play a role. If the substrate has a high carbon equivalent, it may be more susceptible to hydrogen-induced cracking, which can then propagate into the cladding layer. The paper does not discuss this in detail, but it is a factor that we must consider in our practice.
Study Insights and Implications
This paper is a valuable reminder that failure analysis is not just about identifying the cause; it is about understanding the interaction between material, process, and design. The authors have done a thorough job of identifying both the material and mechanical factors, and they have provided a clear explanation of the failure mechanism.
From a practical standpoint, the key takeaways are as follows. First, always verify the chemical composition of the cladding consumables, especially the impurity content. Second, use a cladding alloy that is appropriate for the service conditions, including the temperature and the load. Third, consider the mechanical design of the component, including the support conditions and the expected stresses. Fourth, use an appropriate PWHT cycle to relieve residual stresses without causing reheat cracking.
Reference Value and Outlook
This paper is an excellent reference for engineers involved in the cladding of large components. It provides a detailed case study of a real failure, and it offers practical guidance on how to prevent similar failures in the future. The next step for the industry would be to develop more advanced cladding alloys that are resistant to both hot cracking and reheat cracking, and to develop more sophisticated stress analysis methods that can predict the risk of cracking in cladded components.
In conclusion, this paper is a must-read for anyone involved in the cladding of heavy-duty components. It demonstrates that cracking is not just a welding problem; it is a system problem that involves material selection, process control, and mechanical design. The key is to take a holistic approach and to consider all the factors that can contribute to failure.
Zhuojin Pipe Fitting Co., Ltd