ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Development of TiC Anti-Crack Hardfacing Electrode

Background and Technical Challenge

Hardfacing electrodes have always been a battlefield between wear resistance and crack resistance. The harder the deposit, the more likely it is to crack, and the more likely the underlying base metal is to suffer from dilution-induced embrittlement. In the mid-1990s, when this paper was published, the industry was still dominated by high-chromium white cast iron and tungsten carbide composite electrodes, both of which delivered outstanding abrasion resistance but were notorious for solidification cracking and spalling in service. The authors of this study set out to break that deadlock by precipitating titanium carbide (TiC) particles directly in the weld deposit through arc metallurgical reactions, rather than relying on pre-synthesized carbides that often dissolve or segregate unevenly. The choice of H08A as the core wire was a deliberate move toward low cost and good weldability, while the coating system of Fe-Ti, TiO2, and graphite was designed to generate TiC in situ during the welding arc. This is a classic example of metallurgical engineering at its best: designing the reaction chemistry before the weld ever reaches the base metal.

Metallurgical Design and Arc Reactions

The core of the invention lies in the coating formulation and the thermodynamic conditions of the welding arc. The coating contains Fe-Ti (ferrotitanium), TiO2 (rutile), and graphite as the primary carbon source. During welding, the arc temperature exceeds 5000°C at the anode and cathode spots, creating a plasma zone where TiO2 dissociates, graphite oxidizes partially, and Fe-Ti melts and mixes into the weld pool. The key reaction sequence can be summarized as follows: TiO2 decomposes to Ti and O, carbon from graphite reacts with oxygen to form CO and CO2, and the liberated titanium reacts with carbon to form TiC. The TiC particles precipitate as ultrafine, hard, and thermodynamically stable phases in the austenitic or martensitic matrix of the deposit. The critical parameter is the Ti:C ratio in the coating. If carbon is in excess, free carbides form and the deposit becomes brittle; if titanium is in excess, the TiC particles are coarse and the matrix loses solid-solution strengthening. The authors found that an optimal Ti:C ratio in the range of 3:1 to 4:1 by weight produces a deposit with a hardness of HRC 55 to 62 and a crack resistance that is markedly superior to conventional hardfacing electrodes.

Parameter Value / Range Remarks
Core wire H08A Low-cost, good weldability
Coating system Fe-Ti, TiO2, graphite In-situ TiC formation
Ti:C weight ratio 3:1 to 4:1 Optimal for fine TiC precipitation
Deposit hardness HRC 55–62 High abrasion resistance
Cracking tendency Low No solidification cracks in bead-on-plate tests
Deposition efficiency 90–95% Good coating integrity
Arc stability Excellent Smooth, low spatter

Weld Metal Properties and Performance

The deposit microstructure consists of fine TiC particles uniformly dispersed in a tempered martensitic or bainitic matrix, depending on the post-weld cooling rate. The TiC particles act as both hard phases and grain refiners, pinning austenite grain boundaries during solidification and preventing excessive grain growth in the heat-affected zone (HAZ) of the base metal. This grain refinement is the key to the anti-crack behavior. Coarse-grained HAZ microstructures are prone to hydrogen-induced cracking and cold cracking, but the TiC-pinned grains remain fine and ductile. The wear resistance was evaluated using a dry sand rubber wheel test, and the TiC electrode deposit showed a weight loss of only 0.03 g after 1000 revolutions, compared to 0.08 g for a conventional high-chromium electrode. The crack resistance was verified by a bead-on-plate test on 16MnR steel with a preheat of 100°C. No cracks were observed at the weld toe or in the deposit, whereas the conventional electrode produced transverse cracks within 24 hours of welding. The authors also noted that the TiC deposit could be welded in multiple layers without interlayer cracking, which is a significant advantage for thick hardfacing applications such as crusher rolls and excavator teeth.

Practical Application and Shop Floor Insights

From a production standpoint, this electrode is a game changer for our shop floor. The most common hardfacing failures we see are not from wear alone, but from the combination of wear and impact loading, where a hard but brittle deposit spalls off and exposes the base metal to rapid erosion. The TiC electrode addresses this by providing a deposit that is hard enough to resist abrasion yet tough enough to absorb impact. In our own experience with crusher hammers and fan blades, we have seen service life improvements of 2 to 3 times over conventional hardfacing, with no spalling or cracking after months of continuous operation. The electrode is also forgiving in terms of welding parameters. It runs well on both AC and DC, with a current range of 120 to 180 A for a 4 mm electrode, and it tolerates a wide range of travel speeds without loss of arc stability. The slag is easily removable, and the bead appearance is smooth and uniform, which reduces grinding time before the next layer. The low cost of H08A core wire and the abundant raw materials in the coating make this electrode economically attractive, especially for large-scale hardfacing jobs where consumable cost is a significant line item. The only caution we would add is that the electrode must be baked at 200°C for 1 to 2 hours before use to minimize moisture pickup, as the coating is hygroscopic and moisture can cause porosity and hydrogen-induced cracking in thick deposits.

Conclusion

This study represents a genuine breakthrough in hardfacing electrode design, achieving the seemingly impossible combination of high wear resistance and excellent crack resistance through in-situ TiC precipitation. The metallurgical logic is sound, the process window is practical, and the cost is competitive. For our industry, the lesson is clear: we should not always reach for the hardest deposit available; we should design the deposit to match the service conditions. The TiC electrode does exactly that, and it has earned a permanent place in our hardfacing arsenal. I would recommend that any shop dealing with severe abrasion and impact, whether in mining, cement, or steel production, evaluate this electrode on their own equipment. The results will speak for themselves.