Feasibility Study of 2507 Super Duplex Stainless Steel Strip Electroslag Cladding
Background and Material Selection
Super duplex stainless steel, particularly the 2507 grade, is the material of choice for offshore oil and gas equipment, desalination plants, and chemical processing vessels where both high strength and exceptional corrosion resistance are required. The challenge with 2507 is its high alloy content, especially chromium, molybdenum, and nitrogen, which makes it susceptible to sigma phase precipitation and ferrite-austenite imbalance during welding and cladding. When we clad a carbon steel or low-alloy steel base with 2507, we are essentially creating a bi-metallic component where the cladding must meet the same corrosion and mechanical requirements as a solid 2507 forging. The authors of this study chose the strip electroslag cladding (ESW) process with Sandvik EQ2594 strip and Sandvik 47S flux, a combination specifically designed for super duplex applications. The EQ2594 strip has a nominal composition of 25% Cr, 9% Ni, 3.5% Mo, and 0.25% N, which is closely matched to the 2507 base metal to minimize dilution effects and maintain phase balance. The choice of electroslag over submerged arc is significant: ESW has a lower heat input per unit of deposited metal, which reduces dilution and promotes a more uniform ferrite-austenite ratio in the deposit.
Process Parameters and Experimental Setup
The experimental setup involved a strip cladding head with a 60 mm wide strip electrode, a flux bed depth of 25 to 30 mm, and a welding current of 700 to 900 A at a voltage of 26 to 30 V. The travel speed was set at 15 to 20 cm/min, and the preheat was maintained at 150°C to prevent cold cracking in the base metal. The authors systematically varied the heat input by adjusting current and speed, and they evaluated the resulting deposit for ferrite content, hardness, and corrosion resistance. The critical finding was that the ferrite content in the deposit must be controlled within the range of 35% to 55% by volume, as measured by a ferritscope, to ensure both mechanical toughness and resistance to pitting and stress corrosion cracking. Too much ferrite leads to low impact toughness and susceptibility to hydrogen embrittlement, while too little ferrite results in poor pitting resistance and a risk of sigma phase formation during post-weld heat treatment.
| Parameter | Value / Range | Remarks |
|---|---|---|
| Strip electrode | Sandvik EQ2594, 60 mm wide | Matched to 2507 composition |
| Flux | Sandvik 47S | Agglomerated, low moisture |
| Welding current | 700–900 A | DC reverse polarity |
| Arc voltage | 26–30 V | Stable arc, low spatter |
| Travel speed | 15–20 cm/min | Controlled heat input |
| Preheat | 150°C | Prevents HAZ cold cracking |
| Ferrite content | 35–55 vol% | Optimal phase balance |
| Deposit hardness | 220–260 HV | Uniform across thickness |
| Dilution | 8–12% | Low, typical of ESW |
Weld Metal Properties and Phase Balance
The microstructural analysis of the deposit revealed a fine, uniform distribution of austenite islands in a ferrite matrix, with no evidence of sigma phase or chi phase precipitation at the weld interface. The ferrite content, measured at 45% in the as-welded condition, remained stable after a post-weld heat treatment at 300°C for 4 hours, which is a common stress-relief cycle for duplex stainless steel components. The impact toughness at -40°C was measured at 80 J, which is well above the typical minimum of 45 J required for offshore applications. The corrosion resistance was evaluated using the ASTM G48 ferric chloride test, and the deposit showed a critical pitting temperature (CPT) of 55°C, compared to 50°C for a conventional 2205 duplex cladding. This 5°C improvement is directly attributable to the higher molybdenum and nitrogen content of the 2507 grade. The authors also performed a bend test on the cladding interface, and the specimens passed without any cracks or delamination, confirming that the bond between the deposit and the base metal is metallurgically sound. One of the most important practical observations was that the electroslag process produced a very smooth, uniform bead with minimal undercut, which significantly reduced the need for grinding and rework before the next pass.
Engineering Practice Considerations
From a fabrication standpoint, this study validates the use of strip electroslag cladding for 2507 super duplex on large pressure vessel shells and heads. In our own shop, we have used this process for the internal cladding of hydrocracker reactors and separator vessels, and the results have been consistently good. The key practical lessons we have learned are: first, the flux must be stored in a dry, heated environment and baked at 300°C for 2 hours before use, because moisture in the flux is the primary cause of porosity and hydrogen-induced cracking in duplex deposits. Second, the strip electrode must be kept clean and free of oil or grease, as any contamination will cause arc instability and slag inclusions. Third, the welding parameters must be closely monitored and recorded for every pass, because a slight deviation in heat input can shift the ferrite content outside the acceptable range. We have seen cases where a welder increased the travel speed to finish a shift faster, and the resulting deposit had a ferrite content of only 30%, which failed the corrosion test. The lesson is that process discipline is non-negotiable when working with super duplex materials. The cost of a failed cladding run is not just the rework time; it is the potential for a catastrophic failure in service if the cladding is left as-is.
Conclusion
This study provides a solid technical foundation for the use of 2507 super duplex strip electroslag cladding in equipment manufacturing. The combination of EQ2594 strip and Sandvik 47S flux, with the optimized parameters presented here, produces a deposit that meets all the requirements for offshore and chemical service: high strength, excellent corrosion resistance, and a stable ferrite-austenite phase balance. The process is feasible for production, but it demands rigorous process control and disciplined execution. I would recommend that any fabricator considering this process first perform a welding procedure qualification (WPQ) on the exact base metal and thickness they intend to use, and then run a production trial on a full-size component before committing to a large order. The data in this paper is a starting point, not a substitute for your own qualification testing. With that caveat, this is a proven and reliable process that has earned its place in our manufacturing toolbox.
Zhuojin Pipe Fitting Co., Ltd