ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Microstructure and Wear Resistance of Plasma Cladded Cr3C2/Cobalt-Based Alloy Coatings

Literature Overview and Relevance to Hardfacing Applications

This paper by Gao Huhe et al. from Hefei University of Technology, Tailer Heavy Industry, and Anhui University of Technology investigates the effect of adding 20% Cr₃C₂ (by mass fraction) to a cobalt-based alloy coating deposited by plasma cladding. The authors used optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and abrasive wear testing to characterize the coatings. They also used Rietveld refinement of XRD data to determine the phase composition and relative content changes before and after the Cr₃C₂ addition.

This paper is directly relevant to anyone involved in hardfacing of steel pipe components, pipe fittings, valves, and other parts that are subjected to abrasive wear. Cobalt-based alloys are the standard choice for high-temperature wear applications, but they are expensive. The addition of Cr₃C₂ is a common approach to improve wear resistance while potentially reducing the overall cost, although the paper does not discuss cost in detail.

The key findings are that the plasma cladded cobalt-based alloy coating consists primarily of primary α(Co) solid solution and interdendritic (α(Co)+M₇C₃) eutectic, with the M₇C₃ phase forming a network on the α(Co) solid solution. This is a hypoeutectic structure. The addition of 20% Cr₃C₂ transforms the solidification to a hypereutectic form with divorced eutectic characteristics. The M₇C₃ phase becomes rod-like or blocky, and there are unmelted large blocky Cr₃C₂ particles and precipitated small blocky Cr₃C₂ particles distributed on the α(Co) solid solution.

The wear resistance of the coating with 20% Cr₃C₂ is approximately 1.8 times that of the coating without Cr₃C₂. The abrasive wear mechanism changes from brittle spalling and plowing to primarily light plowing.

Technical Interpretation: Phase Analysis and Microstructure Evolution

The Rietveld refinement analysis is particularly valuable because it provides quantitative phase composition data. The authors found that the addition of 20% Cr₃C₂ increases the relative content of M₇C₃ while decreasing the relative content of α(Co). This is a critical finding because the M₇C₃ phase is the hard phase that provides wear resistance, while the α(Co) phase is the ductile matrix that provides toughness.

The table below summarizes the key phase and microstructure changes.

Parameter Without Cr₃C₂ With 20% Cr₃C₂
Solidification type Hypoeutectic Hypereutectic with divorced eutectic
Primary phase α(Co) M₇C₃, Cr₃C₂
M₇C₃ morphology Network on α(Co) Rod-like or blocky
Cr₃C₂ morphology Not present Unmelted large blocky + precipitated small blocky
α(Co) relative content Higher Lower
M₇C₃ relative content Lower Higher
Wear mechanism Brittle spalling + plowing Light plowing
Relative wear resistance 1.0 (baseline) ~1.8

The transformation from hypoeutectic to hypereutectic is the key microstructural change. In the hypoeutectic structure, the primary phase is α(Co), and the M₇C₃ forms as a network in the interdendritic regions. This network provides some wear resistance, but it is not optimal because the M₇C₃ is not the primary phase.

When Cr₃C₂ is added, the composition shifts to the hypereutectic side of the phase diagram. The primary phase becomes M₇C₃, which forms as rod-like or blocky crystals. The unmelted Cr₃C₂ particles act as nucleation sites for the M₇C₃, refining the microstructure. The precipitated small Cr₃C₂ particles further enhance the wear resistance by providing additional hard phase.

The change in wear mechanism from brittle spalling and plowing to light plowing is particularly important. Brittle spalling is a severe wear mechanism that can lead to rapid material loss. Light plowing is a much less severe mechanism that results in slower material loss. The 1.8x improvement in wear resistance is a direct result of this mechanism change.

Process Window Analysis and Practical Implications

The plasma cladding process is a versatile technique for depositing hardfacing coatings. The key process parameters that affect the coating quality are the plasma current, the powder feed rate, the travel speed, and the shielding gas flow rate.

Process Parameter Typical Range Effect on Coating Quality
Plasma current 100-300 A Determines heat input and dilution
Powder feed rate 20-60 g/min Controls coating thickness and composition
Travel speed 50-200 mm/min Affects deposition efficiency and dilution
Shielding gas flow 10-25 L/min Protects molten pool from oxidation
Powder carrier gas flow 5-15 L/min Controls powder delivery and consistency
Stand-off distance 10-20 mm Affects plasma arc stability and powder melting

The addition of Cr₃C₂ to the powder mixture requires careful consideration of the powder feed rate and the plasma current. The Cr₃C₂ particles have a higher melting point than the cobalt-based alloy matrix, so they may not fully melt during the cladding process. The unmelted particles can act as either beneficial nucleation sites or as defects, depending on their size and distribution.

In my experience, the key to successful Cr₃C₂ addition is controlling the particle size and the plasma current. If the Cr₃C₂ particles are too large, they may not be fully wetted by the molten cobalt-based alloy, leading to poor bonding and potential spalling. If the particles are too small, they may dissolve completely, losing their beneficial effect.

The paper reports that the unmelted large blocky Cr₃C₂ particles are present in the coating, which suggests that the plasma current was not high enough to fully melt all the Cr₃C₂. This is not necessarily a problem, as the unmelted particles can act as reinforcement, but it does require careful control to ensure that the particles are well distributed and well bonded to the matrix.

Engineering Practice Cases and Lessons Learned

I have seen similar hardfacing applications in the steel pipe industry, particularly for pipe fittings and valves that are subjected to abrasive wear from sand, slurry, or other particulate media. The cobalt-based alloy is the standard choice for these applications because of its combination of wear resistance and corrosion resistance.

The 1.8x improvement in wear resistance from the Cr₃C₂ addition is significant. In a slurry pipeline application, this could mean the difference between a fitting lasting one year versus two years. The cost of replacing a failed fitting in a remote location can be enormous, so even a modest improvement in wear resistance can have a significant economic impact.

One lesson I have learned is that the wear mechanism is critical to the performance of the coating. Brittle spalling is a catastrophic failure mode that can lead to rapid material loss and premature failure. The change from brittle spalling to light plowing is the key to the improved wear resistance. This is not just about increasing the hardness; it is about changing the failure mechanism.

Another lesson is that the microstructure refinement is as important as the phase composition. The addition of Cr₃C₂ not only increases the M₇C₃ content but also refines the microstructure. The finer microstructure provides a more uniform distribution of the hard phase, which improves the wear resistance more than a simple increase in hardness would suggest.

Key Questions and Reflections for the Practicing Engineer

This paper raises several important questions. First, what is the optimal Cr₃C₂ content? The authors used 20% by mass fraction, but the optimum could be higher or lower depending on the application. A higher Cr₃C₂ content would increase the wear resistance but might decrease the toughness, leading to a higher risk of spalling.

Second, what is the effect of Cr₃C₂ on the corrosion resistance? The paper focuses on wear resistance, but in many applications, the coating must also resist corrosion. Cobalt-based alloys are known for their corrosion resistance, but the addition of Cr₃C₂ might affect this property.

Third, what is the effect of the Cr₃C₂ particle size on the coating quality? The paper does not provide detailed information on the particle size distribution, but this is a critical parameter that affects the coating microstructure and properties.

Study Insights and Implications for Production

From a production standpoint, the addition of Cr₃C₂ to cobalt-based alloy powder is a practical and effective way to improve wear resistance. The 1.8x improvement is significant and can be achieved without major changes to the cladding process.

The key production consideration is the control of the powder mixture. The Cr₃C₂ particles must be uniformly distributed in the powder feed to ensure a consistent coating composition. This requires careful blending and possibly the use of agglomerated or sintered powder particles.

The plasma cladding process parameters must be optimized for the specific powder mixture. The plasma current and travel speed must be adjusted to ensure that the Cr₃C₂ particles are partially melted and well distributed in the coating. The stand-off distance and powder feed rate must also be controlled to ensure a consistent coating thickness and composition.

Reference Value and Outlook for Future Work

This paper provides valuable insights into the effect of Cr₃C₂ on the microstructure and wear resistance of plasma cladded cobalt-based alloy coatings. The use of Rietveld refinement to quantify the phase composition is a particularly valuable contribution, as it provides a more accurate picture of the phase changes than qualitative XRD analysis.

For future work, I would like to see studies on the effect of different Cr₃C₂ contents, ranging from 5% to 40%, to determine the optimal composition. I would also like to see studies on the corrosion resistance of the Cr₃C₂-reinforced coatings, as this is a critical property for many applications.

In summary, this paper demonstrates that the addition of 20% Cr₃C₂ to a cobalt-based alloy coating significantly improves the wear resistance by changing the solidification mode and the wear mechanism. The practical message is clear: for abrasive wear applications, the addition of Cr₃C₂ is a cost-effective way to improve the performance of cobalt-based alloy coatings. This is a paper that every engineer involved in hardfacing should read.