ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Q345R Tubesheet Strip Cladding Process: A Practical Review

Literature Overview and Context

This 2010 paper from Wenzhou Tianlong Light Industry Equipment Co., Ltd. addresses a real production problem in pressure vessel fabrication: the corrosion-resistant cladding of Q345R tubesheets. The authors compare the new strip cladding process with traditional manual welding and highlight the efficiency and quality advantages, but also the significant distortion problem that arises when the cladding thickness is large. They discuss the issues encountered during implementation and the solutions adopted.

Strip Cladding vs. Manual Welding

Strip cladding is a high-deposition-rate process that uses a wide strip electrode instead of a round wire. The typical strip width is 30–60 mm, and the deposition rate is several times higher than manual welding. The quality is also more consistent because the process is mechanized and the heat input is more uniform.

Parameter Manual Welding Strip Cladding
Deposition rate Low (1–2 kg/h) High (10–20 kg/h)
Quality consistency Variable Consistent
Heat input Low High
Distortion risk Low High
Dilution control Difficult Better with proper parameters
Surface finish Rough Smooth

Distortion Control Challenges

The main problem with strip cladding is the high heat input, which causes significant distortion in the tubesheet. When the cladding thickness is large, the heat input increases further, and the distortion becomes severe enough to cause rejection. The authors discuss this problem and the solutions they implemented.

Root Cause Analysis

The distortion is caused by the differential thermal expansion between the clad layer and the base metal. The cladding layer, typically austenitic stainless steel, has a higher coefficient of thermal expansion than the Q345R carbon steel. As the cladding cools, the austenitic layer contracts more, creating residual stresses that cause the tubesheet to bow.

Countermeasures

The authors likely implemented several countermeasures, although the abstract does not detail them. Based on my experience, the effective solutions include:

  1. Balanced cladding: Cladding both sides of the tubesheet to balance the residual stresses.
  2. Low heat input techniques: Using narrow strips, lower current, and faster travel speeds.
  3. Sequential cladding: Cladding in a sequence that minimizes distortion, such as alternating passes or using a back-step technique.
  4. Post-weld heat treatment: Stress-relieving the tubesheet after cladding.
  5. Mechanical straightening: If the distortion is within a manageable range, mechanical straightening can be used.

Welding Procedure Qualification

The paper mentions welding procedure qualification, which is a critical step in pressure vessel fabrication. For strip cladding of Q345R tubesheets, the qualification must include:

Practical Implications for Heat Exchanger Fabrication

This topic is directly relevant to the fabrication of shell-and-tube heat exchangers, which are used extensively in oil and gas processing, chemical plants, and power generation. The tubesheet is a critical component that separates the shell side from the tube side, and the corrosion-resistant cladding is essential for service in corrosive environments.

In my experience, the distortion problem is real and can cause significant rework if not controlled. I have seen tubesheets that were rejected because the distortion exceeded the flatness tolerance, resulting in expensive rework or replacement.

Key Questions and Reflections

The paper raises an important question: what is the maximum cladding thickness that can be applied without excessive distortion? The answer depends on the tubesheet diameter, the cladding material, and the process parameters. In practice, I have seen successful strip cladding up to 6 mm thick on large tubesheets, but the distortion control becomes increasingly difficult beyond that.

Another question is whether the distortion can be predicted and compensated for. With modern computational tools, it is possible to simulate the residual stresses and distortion, but the accuracy depends on the material properties and the process parameters. In practice, I rely on experience and conservative process parameters.

Study Insights and Implications

This paper is a practical reminder that the advantages of strip cladding — high efficiency and consistent quality — come with a cost: distortion. The key to successful application is to understand the distortion mechanism and implement effective countermeasures. I would emphasize the importance of balanced cladding and low heat input techniques, and I would always qualify the procedure before production.

The lesson for my engineers is that process selection is not just about efficiency; it is about the total cost of fabrication, including rework and rejection. Strip cladding is the right choice for large tubesheets, but only if the distortion is controlled.