Nitrogen Alloyed Hardfacing Alloy: Microstructure and High-Temperature Wear Resistance
Literature Overview and Context
This 2011 paper from Hohai University, Jiangsu University of Science and Technology, and Huazhong University of Science and Technology addresses a sophisticated metallurgical approach to hardfacing: nitrogen alloying of martensitic stainless steel. The authors studied the microstructure and high-temperature wear resistance of a nitrogen-alloyed martensitic stainless steel hardfacing deposit. They found that the microstructure consists of martensite and complex Nb-Ti carbonitrides, and that the wear mechanism is abrasive wear caused by oxide scale from the carbon steel counterface adhering to the hardfacing surface.
Nitrogen Alloying Mechanism
Role of Nitrogen
Nitrogen is a strong austenite former and a potent solid-solution strengthener in stainless steels. In martensitic stainless steel hardfacing deposits, nitrogen increases the hardness and the high-temperature strength by forming carbonitrides with niobium and titanium. The nitrogen also improves the corrosion resistance and the pitting resistance, which is beneficial in many service environments.
Nb-Ti Carbonitride Precipitation
The authors found that nitrogen alloying promotes the precipitation of Nb-Ti complex carbonitrides. These carbonitrides are dispersed in the martensite matrix and provide dispersion strengthening. The dispersion of these fine particles increases the high-temperature hardness and the wear resistance.
High-Temperature Wear Mechanism
The authors identified the wear mechanism as abrasive wear caused by the oxide scale from the carbon steel counterface. At high temperature, the carbon steel surface oxidizes, and the oxide scale adheres to the hardfacing surface. This adhered oxide then acts as an abrasive, causing three-body abrasive wear on the hardfacing surface.
This is an important finding because it explains why the wear rate is not solely determined by the hardness of the hardfacing alloy. The oxide scale from the counterface plays a critical role in the wear process.
| Parameter | Without Nitrogen | With Nitrogen |
|---|---|---|
| Microstructure | Martensite + carbides | Martensite + Nb-Ti carbonitrides |
| Carbonitride distribution | Coarse | Fine and dispersed |
| High-temperature hardness | Lower | Higher |
| Wear resistance | Lower | Improved |
| Wear mechanism | Adhesive + abrasive | Abrasive (oxide scale) |
Practical Implications for High-Temperature Service Components
This alloy system is directly relevant to components that operate at high temperature in abrasive service, such as:
- Mandrels and piercing tools in seamless pipe production, which see high temperature and abrasive wear.
- Valve seats and gates in high-temperature steam service.
- Extrusion dies and hot forming tools.
- Wear plates in high-temperature material handling systems.
In my experience, the key advantage of nitrogen alloying is the combination of high-temperature hardness and wear resistance without sacrificing toughness. The fine dispersion of carbonitrides provides strengthening without embrittlement.
Process Considerations and Lessons Learned
Nitrogen alloying in hardfacing deposits requires careful control of the nitrogen content. Too much nitrogen can cause porosity in the deposit, because the solubility of nitrogen in the weld pool is limited. The nitrogen must be added either through the flux-cored wire or through a nitrogen-containing shielding gas.
In my experience, the most reliable method is to add nitrogen through the flux-cored wire, using a nitride compound in the flux. This ensures a consistent nitrogen content in the deposit. The shielding gas can also be used, but the nitrogen pickup is less predictable.
Another practical point is the need for a post-weld heat treatment to temper the martensite and reduce the residual stresses. The authors do not mention this, but it is important for components that see thermal cycling.
Key Questions and Reflections
The paper does not specify the exact nitrogen content or the Nb and Ti contents. In practice, I would want to know these values to reproduce the results. The optimal nitrogen content is typically 0.1–0.3 wt%, but it depends on the chromium and nickel contents.
Another question is the wear test conditions. The authors used a high-temperature wear test, but the exact temperature and load are not specified. In practice, the wear rate depends strongly on these parameters, and the results may not be directly comparable to service conditions.
Study Insights and Implications
This paper is a good example of how alloy design can be used to improve high-temperature wear resistance. The nitrogen alloying approach is elegant because it uses a low-cost element to achieve a significant improvement in performance. The fine dispersion of Nb-Ti carbonitrides is the key to the improved properties.
The practical lesson for my engineers is that high-temperature wear is not just about hardness; it is about the microstructure and the wear mechanism. Nitrogen alloying is a powerful tool for improving high-temperature wear resistance, but it requires careful control of the nitrogen content and the heat treatment.
Zhuojin Pipe Fitting Co., Ltd