ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Development and Application of High-Speed Electroslag Strip Cladding

Literature Overview and Technical Context

The paper by Zhang Liangcheng and Ding Bixue from Shanghai Boiler Works Co., Ltd. presents a comprehensive review of the development and application of high-speed electroslag strip cladding (ESW). The authors trace the origins of this process to the 1982 IIW (International Institute of Welding) conference and describe its subsequent adoption in the mechanical industry worldwide. The key contribution of the paper is the description of newly developed fluxes that allow for welding speeds up to 350 mm/min and single-layer deposits that meet chemical composition requirements, as well as the development of fluxes containing metallic components for wear-resistant applications.

This is a topic that I have encountered many times in the manufacture of pressure vessels, heat exchangers, and pipe fittings where corrosion-resistant cladding is required. The traditional approach to strip cladding has been submerged arc welding (SAW), which offers high deposition rates but is limited by the need to control dilution and bead shape. The development of high-speed electroslag strip cladding represents a significant advancement, as it allows for faster welding speeds and thinner deposits, which are critical for reducing production time and cost.

Technical Principle and Process Development

The fundamental principle of electroslag strip cladding is that the heat required to melt the strip and the base metal is generated by the electrical resistance of the molten slag, rather than by an arc. This results in a more uniform heat distribution and a smoother bead surface compared to SAW. The process is inherently stable, and the deposition rate is limited primarily by the ability of the flux to maintain a stable slag pool.

The authors describe the historical limitation of ESW as being the flux. Early fluxes were not capable of supporting high welding speeds, which limited the deposition rate. The development of new fluxes, which are described in the paper, has overcome this limitation. These fluxes allow for welding speeds up to 350 mm/min, which is a significant improvement over the traditional 150–200 mm/min for SAW strip cladding.

The key parameters for high-speed ESW strip cladding are summarized below.

Parameter Typical Range Remarks
Strip width 30–60 mm Wider strips increase deposition rate
Strip thickness 0.4–0.6 mm Thinner strips allow for faster welding
Welding current 800–1500 A Higher current increases deposition rate
Arc voltage 20–30 V Lower voltage promotes electroslag mode
Welding speed 200–350 mm/min New fluxes allow for higher speeds
Flux composition Basic or neutral Must be designed for electroslag mode
Preheat temperature 100–200 °C Prevents cracking in carbon steel HAZ

The authors report that with the new fluxes, a single layer can achieve the chemical composition requirements for the cladding. This is a critical achievement, as it eliminates the need for a second pass, which reduces production time and cost by approximately 50%. The single-layer deposit also has a smoother surface, which reduces the amount of machining required.

Application to Stainless Steel and Nickel-Based Alloys

The paper describes the application of high-speed ESW to both stainless steel and nickel-based alloy strip cladding. For stainless steel cladding, the process is used to apply corrosion-resistant layers to carbon steel pressure vessels and heat exchangers. The typical strip materials are 309L, 316L, and 347, which are selected based on the service environment.

For nickel-based alloy cladding, the process is used to apply corrosion-resistant layers to carbon steel components in sour service or high-temperature applications. The typical strip materials are Inconel 625, Inconel 825, and Hastelloy C-276. The use of ESW for nickel-based alloys is particularly advantageous because the low dilution rate ensures that the corrosion resistance of the cladding is not compromised.

The authors also describe the development of fluxes containing metallic components for wear-resistant applications. This is an innovative approach that allows for the deposition of hardfacing alloys with a controlled composition. The metallic components in the flux are transferred to the deposit during welding, which allows for the production of alloys that would be difficult to produce with conventional strip materials.

Quality Control and Defect Analysis

The paper does not provide a detailed discussion of quality control, but based on my experience, there are several critical aspects that must be addressed. The most important is the control of dilution, which determines the chemical composition of the cladding layer. Dilution is influenced by the welding current, the welding speed, and the flux composition. A higher welding current increases dilution, while a higher welding speed decreases it. The flux composition also plays a role, as basic fluxes tend to produce lower dilution than acidic fluxes.

Another critical aspect is the control of the slag pool. If the slag pool becomes too shallow, the arc will penetrate the base metal, resulting in excessive dilution. If the slag pool becomes too deep, the process may become unstable, resulting in lack of fusion or porosity. The depth of the slag pool is controlled by the flux feed rate and the welding speed.

The common defects in ESW strip cladding are lack of fusion, porosity, and slag inclusions. Lack of fusion can occur if the welding current is too low or the welding speed is too high. Porosity can occur if the flux is damp or if the shielding is inadequate. Slag inclusions can occur if the slag is not properly removed between passes or if the bead shape is irregular.

Integration with Engineering Practice

This study has direct relevance to the manufacture of pressure vessels, heat exchangers, and pipe fittings for the oil and gas industry. In my experience, the use of strip cladding is standard practice for large-diameter components where the cost of solid corrosion-resistant alloys would be prohibitive. The development of high-speed ESW represents a significant advancement, as it allows for faster production and lower costs.

The authors' description of fluxes containing metallic components for wear-resistant applications is particularly interesting. This technology could be used to produce hardfacing layers on components such as pipe guides, bending dies, and crusher parts. The ability to control the composition of the deposit through the flux opens up new possibilities for alloy design.

However, I would caution that the high-speed ESW process requires careful control of the welding parameters and the flux composition. The process is more sensitive to variations in the flux composition than SAW, and the flux must be designed specifically for the strip material and the application. Additionally, the process requires specialized equipment, which may not be available in all fabrication shops.

Key Questions and Reflections

The paper raises several questions that are relevant to the practical application of high-speed ESW. First, what is the maximum thickness of the cladding layer that can be achieved with a single pass? The paper focuses on thin layers, but in some applications, a thicker layer may be required. Second, how does the process perform on components with complex geometries, such as nozzles or flanges? Third, what is the long-term performance of the cladding layer in aggressive service environments?

From my perspective, the most important question is whether the process can be scaled up to production volumes without sacrificing quality. The paper describes the development of the process, but the real challenge is maintaining consistency across thousands of components. This requires robust process control, including monitoring of welding parameters, flux feed rate, and slag pool depth.

Study Insights and Implications

The study provides a comprehensive review of the development and application of high-speed electroslag strip cladding. The key insights are that the process offers high deposition rates, low dilution, and smooth bead surfaces, which are the three critical factors for corrosion-resistant cladding. The development of new fluxes has overcome the historical limitations of the process, allowing for welding speeds up to 350 mm/min and single-layer deposits that meet chemical composition requirements.

For engineers in the field, the practical takeaway is that high-speed ESW should be seriously considered for cladding applications where production efficiency is critical. The process offers significant advantages over traditional SAW strip cladding, including faster welding speeds, thinner deposits, and lower dilution. However, the process requires specialized equipment and careful control of the welding parameters and flux composition.

Reference Value and Outlook

This paper has significant reference value for engineers involved in the design and manufacture of corrosion-resistant components. The review of the process development and the description of the new fluxes provide a solid foundation for understanding the capabilities and limitations of high-speed ESW. The findings can be used to guide the selection of the process for specific applications.

Looking to the future, I expect to see continued development of high-speed ESW technology. The development of new fluxes with improved properties will further enhance the capabilities of the process. Additionally, the integration of ESW with automated welding systems will improve the consistency and reliability of the process.

In conclusion, this study provides a valuable overview of the development and application of high-speed electroslag strip cladding. The findings on the new fluxes and their capabilities are directly applicable to the design of corrosion-resistant components. The practical implications for production, including the use of the process for stainless steel and nickel-based alloy cladding, are also valuable. I would recommend this paper to anyone involved in cladding or hardfacing applications, as it offers both technical insights and practical guidance.