ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Preheating Selection for Large Gear Tooth Surfacing via Welding CCT Diagrams

1. The Problem: A 1.5-Tonne Gear with Worn Teeth

The authors of this paper faced a familiar problem: a large gear weighing 1.5 tonnes with significant tooth wear, and a decision to make about whether to replace it or repair it. For a gear of this size, replacement means a long lead time and a very large capital outlay. Repair by surfacing is attractive, but it carries a serious risk — the gear is made of 30CrMnMo, a low-alloy steel with high hardenability, and if you weld it without proper preheat, the heat-affected zone will transform to hard, brittle martensite and the gear will crack, either during welding or in service. The paper's contribution is the methodical use of welding CCT (continuous cooling transformation) diagrams to select the preheat temperature. This is exactly the kind of engineering discipline that separates a successful repair from a catastrophic failure.

2. Weldability Analysis of 30CrMnMo

30CrMnMo is a chromium-manganese-molybdenum low-alloy steel. Its carbon equivalent is high enough that it is classified as a steel with poor weldability — you cannot just strike an arc and weld it. The key metallurgical issue is the transformation behaviour. When the steel is heated above the transformation temperature and then cools, the final microstructure depends on the cooling rate. Fast cooling produces martensite, which is hard, strong but brittle, and prone to hydrogen-induced cracking. Slow cooling produces bainite or ferrite-pearlite mixtures, which are tougher and more forgiving. The CCT diagram tells you exactly what cooling rate produces what microstructure, and it is the bridge between the welding parameters and the final properties. The authors correctly identify that preheating is the critical variable, because it controls the cooling rate of the weld and the heat-affected zone. Without preheat, the massive gear acts as a heat sink, and the cooling rate in the HAZ is fast enough to produce martensite. With the right preheat, the cooling rate is slowed down, and the HAZ transforms to a more ductile microstructure.

3. Using the CCT Diagram to Set the Preheat Temperature

The paper references the CCT diagram for 30CrMnMo from the Chinese national low-alloy steel welding CCT diagram collection. The method is straightforward but requires care. You plot the cooling curves for the weld and HAZ on the CCT diagram, and you select a preheat temperature such that the cooling curve passes through the region of the diagram that gives you the desired microstructure — typically bainite or a bainite-ferrite mixture, avoiding the martensite region. The authors selected the preheat temperature based on the cooling curve analysis, and the result was a successful repair of two large gears. From my experience, the practical details matter as much as the theory. You need to measure the preheat temperature properly — not just at one point, but at several points around the gear, because a 1.5-tonne gear has a large thermal mass and the temperature will not be uniform. You also need to maintain the interpass temperature, because if you allow the gear to cool below the preheat temperature between passes, the HAZ of the next pass will cool too fast. And you need to control the post-weld cooling rate — a slow cool, often under insulating blankets, to prevent the formation of martensite after the last pass.

4. Shop Floor Execution and Lessons Learned

The paper reports that two large gears were successfully repaired using this approach. That is the headline result, but the real value is in the method. Let me tell you what I would do on the shop floor, drawing on the paper's logic and my own experience. First, I would verify the material composition of the gear — you cannot assume it is 30CrMnMo just because the drawing says so; I have seen gears that were supposed to be one alloy and were actually another. Second, I would grind out the worn teeth to sound metal, and I would do a dye penetrant or magnetic particle inspection on the ground surface to confirm there are no cracks already present. Third, I would set up the preheat — using gas torches or induction heating, with thermocouples or temperature-indicating crayons to verify the temperature at multiple locations. Fourth, I would select the welding consumable — for a gear tooth repair, a low-hydrogen electrode is essential, and it should be dried properly before use. Fifth, I would weld in a sequence that minimises distortion — a gear tooth is a small area, but the gear itself is large, and the cumulative distortion from many teeth can be significant. Sixth, I would control the interpass temperature and the post-weld cooling. Seventh, I would inspect the repaired teeth — magnetic particle inspection for surface cracks, and hardness testing to confirm the HAZ is not excessively hard. If the hardness is too high, you have a problem, even if no cracks are visible.

5. Final Reflections on CCT-Based Process Design

The CCT diagram is a tool that every welding engineer should use, but it is not a substitute for experience. The CCT diagram tells you what microstructure you will get for a given cooling curve, but it does not tell you what the actual cooling curve will be — that depends on the preheat temperature, the interpass temperature, the heat input, the geometry of the component, and the ambient conditions. The paper's authors did the right thing: they used the CCT diagram to set the preheat, they verified the result by successful repair, and they documented the process. In my career, I have seen too many cases where a repair was attempted without proper preheat, and the result was a cracked gear that had to be scrapped anyway — with the added cost of a failed repair on top of the replacement cost. The message is simple: if you are going to weld a high-hardenability steel, do the homework first. Use the CCT diagram, set the preheat, control the interpass temperature, and slow-cool afterwards. It takes more time and more effort, but it is the difference between a repair that lasts and a repair that fails.