Surfacing Repair of Flue Gas Turbine Blades: Feasibility, Economics and Process
1. Service Conditions and Failure Modes
Flue gas turbine blades operate in one of the harshest environments in a refinery. The gas stream is hot — typically 600 to 700°C at the inlet — and it carries catalyst fines, coke particles and corrosive species. The blades are subjected to high centrifugal stress, thermal cycling, erosion from the particulate-laden gas, and high-temperature corrosion from sulphur and vanadium compounds. The result is a characteristic failure pattern: the leading edge and the tip of the blade suffer erosion and corrosion, the blade loses material, the aerodynamic profile is degraded, and eventually the blade becomes unserviceable. The question the authors address is whether such blades can be repaired by surfacing, and whether the repair is economically justified. From my experience in refinery and petrochemical plant, this is a very practical question. A set of flue gas turbine blades is a significant capital investment, and the lead time for replacement blades can be many months. If a repair can extend the service life by even one operating cycle, the economics are usually favourable.
2. Feasibility Analysis: What Makes a Blade Repairable
The authors analyse the feasibility of surfacing repair for worn blades. The first question is whether the blade material is weldable. Flue gas turbine blades are typically made of nickel-based or cobalt-based superalloys, or of martensitic stainless steels, depending on the design. Some of these alloys are readily weldable; others are notoriously difficult. The second question is whether the worn area is accessible and can be prepared for welding. Blade tips and leading edges are accessible, but if the erosion has progressed to the point where the blade is thin or the damage is deep, the repair may not be structurally sound. The third question is whether the repair can restore the aerodynamic profile. A blade that has been repaired by surfacing will have a deposit layer that must be machined back to the original profile. If the deposit is not uniform, the blade will be out of balance, and the vibration will cause problems in service. The fourth question is whether the repair can withstand the service environment. The deposit material must have similar or better resistance to erosion and corrosion than the original blade material.
3. Material Selection for the Surfacing Deposit
The authors selected a suitable surfacing material for the blade repair. This is the heart of the problem. The deposit must match the blade material in thermal expansion coefficient, to avoid thermal fatigue cracking. It must have good high-temperature strength, to withstand the centrifugal stress. It must have good erosion resistance, to withstand the particulate-laden gas. And it must have good high-temperature corrosion resistance, to withstand the sulphur and vanadium attack. In practice, the choice is usually a nickel-based or cobalt-based alloy with high chromium content for oxidation resistance, and with tungsten or molybdenum additions for solid-solution strengthening. The exact composition depends on the blade material and the service conditions. I have seen repairs done with cobalt-based alloys for blades that operate at very high temperatures, and nickel-based alloys for blades that operate at lower temperatures but with more corrosive conditions. The key is to match the deposit to the service environment, not just to the blade material.
4. Process Development and Execution
The authors developed a specific surfacing process for the blade repair. From my experience, the process must address several practical issues. First, the blade must be cleaned thoroughly before welding — any residual catalyst or corrosion products will contaminate the weld and cause porosity or lack of fusion. Second, the worn area must be ground back to sound metal, and the grinding must be done carefully to avoid overheating the blade and causing metallurgical damage. Third, the welding process must be selected — for blade tips and leading edges, TIG welding is often the best choice because it gives good control over the deposit and low heat input. For larger areas, plasma transfer arc (PTA) surfacing can be more productive. Fourth, the welding parameters must be controlled to minimise dilution — if too much base metal is melted into the deposit, the deposit composition will be diluted and the properties will be degraded. Fifth, the blade must be stress-relieved after welding, or at least cooled slowly, to avoid residual stress and distortion. Sixth, the repaired blade must be machined back to profile and inspected — dimensional inspection to confirm the profile, dye penetrant or radiographic inspection to confirm the deposit is sound, and hardness testing to confirm the deposit properties.
5. Economic Justification and Lessons Learned
The authors analysed the economics of repair versus replacement, and the conclusion is that repair is economically justified. This matches my experience. The cost of a repair is typically 20 to 40% of the cost of a new blade, and the repair can be done in a fraction of the lead time. The key is to do the repair properly. I have seen repairs that failed because the deposit was not properly bonded, because the deposit was machined too thin, because the welding was done without proper preheat and the blade cracked, or because the deposit material was not matched to the service environment. The lessons are clear. Do the feasibility analysis honestly — if the blade is too worn, do not try to repair it. Select the deposit material based on the service environment, not just on the blade material. Control the welding process to minimise dilution and distortion. Inspect the repair thoroughly before returning the blade to service. And document everything, because the next time you have a similar blade, you will want to know what worked and what did not. Flue gas turbine blade repair is a high-value, high-risk operation, but if it is done right, it saves a lot of money and a lot of downtime.
Zhuojin Pipe Fitting Co., Ltd