ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Surfacing Repair of Universal Mill Intermediate Housing: A Practical Study Note

Literature Overview

This paper documents the repair of a universal mill intermediate housing at Laiwu Steel's medium section line. The housing had been in service for over ten years, and all working surfaces were severely worn, directly affecting the quality of rolled products. The repair approach combined surfacing welding followed by mechanical machining. After removing the fatigue layer from worn surfaces, the repair faces were built up by welding, then machined back to drawing dimensions on a large boring and milling machine. Failed bolt holes were also restored. The repaired housing achieved original design dimensional accuracy and extended service life.

Technical Interpretation

Root Cause of Wear

The intermediate housing of a universal mill is subjected to complex cyclic loading. The working surfaces experience high contact stresses, abrasive wear from scale and oxide, and occasional impact loads. After ten years of service, the fatigue layer on the contact surfaces becomes work-hardened and micro-cracked. Simply grinding or machining the surface would not restore the original dimensions, and leaving the fatigue layer in place would accelerate re-wear.

Repair Sequence and Key Points

Step Operation Key Technical Considerations
1 Pre-inspection Dimensional survey, crack detection (MT/PT), hardness mapping
2 Fatigue layer removal Machining to sound metal, typically 3–5 mm depth
3 Preheating 150–250 °C for cast steel, slow heating to avoid thermal shock
4 Surfacing welding Low-hydrogen electrodes, buttering layer then build-up layers
5 Post-weld treatment Stress relief or controlled cooling, avoid rapid cooling
6 Machining Large boring/milling to final dimensions
7 Bolt hole repair Re-drilling, thread restoration, or insert installation
8 Final inspection Dimensional verification, hardness testing, NDT

Welding Consumables and Process

For cast steel housings, the typical base material is a low-alloy cast steel such as ZG270-500 or similar. The choice of filler metal is critical. A low-hydrogen electrode with matching strength and toughness is preferred. The buttering layer should be applied with lower current to minimize dilution, followed by fill and cap passes with higher deposition rate. Interpass temperature control is essential to prevent hydrogen-induced cracking in the HAZ.

Distortion Control

The housing is a massive, rigid structure, but uneven heating during surfacing can still cause distortion. The repair sequence should be planned to balance heat input across the structure. Back-step or skip-welding techniques help distribute heat. Preheating reduces the temperature gradient and thus thermal stress. After welding, controlled cooling in still air or with insulation blankets is recommended.

Engineering Practice and Lessons

Case Experience

In my own experience with heavy mill equipment, the decision to repair versus replace is an economic one. A new housing may cost millions and require long lead times. Surfacing repair, when done properly, can extend service life by several years at a fraction of the cost. The key is to assess the extent of wear and the condition of the base material before committing.

Common Defects and Countermeasures

Defect Likely Cause Countermeasure
Cracking in HAZ High hardness, hydrogen, restraint Preheating, low-hydrogen electrodes, PWHT
Porosity Damp electrodes, surface contamination Dry electrodes, clean and preheat surface
Lack of fusion Low current, incorrect angle Increase current, adjust technique
Distortion Uneven heat input Balanced sequence, controlled cooling
Undercut Excessive current, poor technique Reduce current, improve manipulation

Quality Control

After machining, the repaired surfaces must be verified for dimensions and surface quality. Hardness testing ensures the build-up layer has adequate wear resistance. Ultrasonic testing or magnetic particle inspection may be used to detect subsurface defects. The bolt holes should be checked for thread integrity and alignment.

Key Questions and Reflections

One question that always arises is whether the repaired housing will perform as well as the original. In practice, the surfacing layer can be designed to have better wear resistance than the original material by selecting appropriate hardfacing consumables. However, the interface between the build-up and the base metal is a potential weak point. Ensuring good fusion and controlling dilution are essential.

Another consideration is the fatigue behavior of the repaired structure. The heat-affected zone may have different properties than the base metal. Post-weld heat treatment can help restore toughness and relieve residual stress. In some cases, a low-temperature stress relief is sufficient.

Study Insights and Implications

This paper is a good example of a practical repair strategy that can be applied to many heavy machinery components. The combination of surfacing and machining is a well-established approach, but the details matter. Preheating, consumable selection, and interpass control are the factors that determine success or failure. The repair of bolt holes is often overlooked but is critical for reassembly and load transfer.

In the steel pipe and fitting industry, similar repair techniques are used for mandrels, dies, and forming rolls. The principles are the same: remove the damaged layer, build up with appropriate filler, and machine back to tolerance. The economic benefit is significant, especially for large, expensive components.

Reference Value and Outlook

The paper provides a useful reference for maintenance engineers and plant managers. It highlights the importance of systematic repair procedures and quality control. Future developments may include the use of automated surfacing systems for better consistency and reduced human error. Laser cladding and cold metal transfer processes offer lower heat input and finer microstructures, which could be beneficial for high-precision repairs.

In conclusion, surfacing repair is a proven and cost-effective method for restoring worn mill housings. The key to success lies in thorough preparation, careful welding, and precise machining. The lessons learned from this case can be applied to similar repairs across the steel industry.