An Initial Exploration of Roll Hardfacing Processes
Literature Overview and Context
The paper by Zhang Wen, published in Special Steel Technology in 1999, provides a practical overview of the roll hardfacing process. The author, an engineer at a special steel company, shares experience from the shop floor on controlling process parameters and operating procedures to achieve good hardfacing results.
This is a short, practical paper, but it addresses a topic of significant economic importance. Rolls are among the most expensive consumables in a rolling mill, and their service life directly affects production costs and product quality. Hardfacing is the standard method for extending roll life, but the process is not straightforward. The paper's focus on process control and operating discipline reflects the reality that roll hardfacing is as much about operator skill and procedure adherence as it is about welding technology.
Interpretation of Technical Points
Process Parameters and Their Control
The paper emphasises the importance of controlling the following parameters:
- Welding current and voltage: These determine the heat input and the deposit characteristics. Too high a current can cause excessive dilution and distortion; too low a current can result in lack of fusion.
- Travel speed: This affects the deposit thickness and bead shape. A consistent travel speed is essential for uniform build-up.
- Wire feed speed: This controls the deposition rate and must be matched to the travel speed to achieve the desired deposit thickness.
- Preheat and interpass temperature: Rolls are typically large, massive components with high thermal mass. Preheating is essential to prevent cracking, and interpass temperature must be controlled to ensure consistent deposit properties.
- Oscillation or weaving: This is used to spread the deposit over a wider area and to control the bead profile.
Operating Procedures
The paper stresses the importance of strict operating discipline. This includes:
- Cleaning the roll surface before hardfacing to remove oil, grease, scale and other contaminants.
- Maintaining the correct electrode or wire extension.
- Ensuring proper shielding gas flow and coverage.
- Monitoring the deposit appearance for signs of defects.
- Controlling the cooling rate after welding to prevent cracking.
Post-Weld Machining
After hardfacing, the roll must be machined to restore its dimensions and surface finish. This requires careful selection of cutting tools and parameters, as the hardfaced surface is significantly harder than the original roll material.
Integration with Engineering Practice
Application in Pipe and Tube Mills
In our industry, rolls are used extensively in:
- Forming rolls: Used in ERW/HFW pipe mills to form the strip into a tube. These rolls see high loads and abrasive wear.
- Sizing rolls: Used to achieve the final pipe diameter and wall thickness.
- Straightening rolls: Used to correct pipe straightness after welding.
The hardfacing of these rolls is a routine maintenance operation, but it requires careful attention to detail. A poorly hardfaced roll will have a short service life, leading to increased downtime and costs.
Common Defects and Countermeasures
| Defect | Root Cause | Countermeasure |
|---|---|---|
| Cracking | Insufficient preheat, high restraint | Increase preheat, use low-hydrogen consumables |
| Porosity | Contamination, inadequate shielding | Clean surface, verify gas flow |
| Lack of fusion | Low current, incorrect travel speed | Increase current, adjust parameters |
| Excessive dilution | High current, slow travel speed | Reduce heat input, increase travel speed |
| Distortion | Uneven heating, excessive heat input | Use proper sequence, control interpass temperature |
Practical Considerations for Large Rolls
Large rolls present unique challenges:
- Thermal management: The massive size of the roll means that heat is conducted away rapidly, making it difficult to maintain the required preheat and interpass temperature. This may require the use of multiple torches or induction preheating.
- Distortion control: The roll may distort during hardfacing due to uneven heating. This can be mitigated by using a balanced welding sequence and by rotating the roll continuously during welding.
- Inspection: After hardfacing, the roll must be inspected for defects. This typically involves UT for subsurface defects and MT or PT for surface defects.
Key Questions and Reflections
The paper raises an important question about the balance between productivity and quality in roll hardfacing. A faster deposition rate is desirable for productivity, but it can lead to higher heat input, increased dilution and a greater risk of defects. The author's emphasis on controlling process parameters reflects this tension.
In my experience, the most common problem in roll hardfacing is not the welding itself but the preparation and the post-weld handling. Rolls that are not properly cleaned or preheated will crack, and rolls that are cooled too quickly after welding will develop residual stress that leads to premature failure.
Another reflection is on the choice of hardfacing material. The paper does not discuss this in detail, but it is a critical decision. For hot rolls, a high-chromium or Ni-based alloy is typically used. For cold rolls, a martensitic stainless steel or tool steel alloy may be more appropriate. The choice depends on the service conditions, including temperature, load and the material being rolled.
Study Insights and Implications
This paper is a useful practical guide for anyone involved in roll hardfacing. It emphasises the importance of process control and operating discipline, which are the keys to success in this application. For engineers in our industry, the key insights are:
- Roll hardfacing requires careful control of welding parameters to achieve the desired deposit properties.
- Preheat and interpass temperature control are essential to prevent cracking.
- Post-weld machining must be planned carefully, as the hardfaced surface is much harder than the original roll material.
The paper would be strengthened by including more specific data on welding parameters and deposit properties. However, as a practical guide, it is valuable and reflects the experience of someone who has actually done the work.
Reference Value and Outlook
For our industry, this work has direct relevance to the maintenance and repair of rolls used in pipe and tube mills. The principles described in the paper apply equally to other large, massive components that require hardfacing. Future work should focus on:
- The development of improved hardfacing alloys with better wear resistance and toughness.
- The use of automated hardfacing systems to improve consistency and productivity.
- The application of advanced NDT techniques to detect defects in hardfaced rolls.
In conclusion, this paper is a practical and useful guide to roll hardfacing. It emphasises the importance of process control and operating discipline, which are the keys to success in this application. The paper's focus on the practical aspects of the process, rather than the theoretical metallurgy, makes it particularly valuable for engineers and technicians on the shop floor. I would recommend this paper to anyone involved in the hardfacing of rolls or similar components, with the caveat that the specific parameters must be developed for each application through welding procedure qualification. The paper demonstrates that roll hardfacing is a skill-intensive process that requires experience, attention to detail and a commitment to quality.
Zhuojin Pipe Fitting Co., Ltd