Repair and Strengthening of a φ1550mm Backup Roll by Submerged Arc Cladding
1. Literature Overview and Why This Paper Still Matters
This 2003 paper from Shandong Metallurgy describes the repair and strengthening of a φ1550mm backup roll from the medium plate mill at Jinan Iron and Steel Group. The authors analysed the service conditions and failure mode, selected a low-crack-sensitivity welding wire, and developed a submerged arc cladding plus special heat treatment route. The repaired roll achieved 2.54 times the service life of a new roll.
I have signed off on dozens of backup roll repairs over the years, and I can tell you this paper is not just about one roll in one mill. It is a case study in the economics of heavy machinery maintenance. A backup roll for a medium plate mill is a major capital asset. The cost of a new forged or cast roll, the lead time for delivery, and the production loss during changeover all make repair an attractive option. The 2.54 times life improvement is the headline number, but the real value lies in the process discipline that made it possible.
2. Failure Analysis and the Logic of the Repair Route
The backup roll in a medium plate mill operates under extreme contact stress, repeated rolling cycles, and potential lubrication or cooling interruptions. The authors correctly identified that the failure mode was not a single catastrophic event but progressive surface degradation. This is typical: spalling, cracking, and wear on the roll body, often concentrated in the contact zone.
The key decision was the choice of welding consumable. The paper notes the selection of a low-crack-sensitivity wire. This is where many repair attempts go wrong. If you pick a wire with high hardness but poor toughness, you will get a hard cladding that looks good on the surface but cracks under the first few thousand tonnes of rolling load. The crack will propagate into the roll body, and you will have a worse problem than before. The low-crack-sensitivity wire is the correct choice because it balances hardness against the ability to tolerate the thermal and mechanical cycling of the rolling process.
The submerged arc cladding process itself is well suited to large cylindrical components. It offers high deposition rates, good fusion, and a stable arc that can be automated for the circumferential welding path. The paper does not give the full process window, but from my experience the critical parameters are:
| Parameter | Typical Range | Practical Notes |
|---|---|---|
| Welding current | 350–500 A | Higher current increases deposition but also heat input |
| Arc voltage | 28–34 V | Must be matched to the wire diameter and flux type |
| Welding speed | 25–40 cm/min | Too fast gives poor fusion; too slow gives excessive dilution |
| Preheat temperature | 150–250 °C | Essential to prevent hydrogen-induced cracking in the HAZ |
| Interpass temperature | 200–300 °C | Controlled to avoid overheating and grain growth |
| Wire diameter | 3.2–4.0 mm | Larger wire for higher deposition, smaller for better control |
The heat treatment after cladding is the other critical step. The paper mentions a special heat treatment process. For a backup roll, this typically involves stress relief to reduce residual stresses from the cladding, followed by a controlled cooling cycle. The stress relief temperature must be high enough to relax the welding residual stresses but low enough not to soften the cladding below its required hardness. This is a narrow window, and the paper rightly highlights it as a key part of the repair route.
3. Engineering Practice: What the Shop Floor Must Get Right
I have seen backup roll repairs fail for reasons that have nothing to do with the welding process itself. The most common problems are:
- Inadequate pre-cleaning. The roll surface must be machined or ground to remove all cracks, spalls, and fatigue-damaged material before cladding. If you weld over a crack, you are simply hiding it. The crack will grow through the new cladding under service load.
- Poor flux handling. Submerged arc welding flux must be dry and free from contamination. Moisture in the flux leads to hydrogen pickup and delayed cracking. I have seen rolls that passed visual inspection but cracked within weeks because the flux was stored in an open bag on a damp floor.
- Incorrect interpass control. The roll is a large thermal mass. If you do not monitor and control the interpass temperature, the roll can overheat, causing grain growth in the cladding and a loss of toughness. Conversely, if you let it cool too much between passes, you increase the risk of cracking.
- Lack of post-weld inspection. The repaired roll must be inspected by ultrasonic testing (UT) and magnetic particle testing (MT) before it goes back into service. UT detects subsurface defects, and MT detects surface cracks. I have seen repairs accepted on visual inspection alone, and the result was a roll that failed in service and damaged the work rolls as well.
The 2.54 times life improvement is a strong result, but it is not automatic. It comes from doing every step correctly: surface preparation, consumable selection, process control, heat treatment, and inspection. The paper is a good example of this discipline, and it is a useful reference for anyone planning a similar repair.
4. Study Insights and Practical Implications
What I take from this paper is not just the technical detail but the mindset. A backup roll repair is not a quick fix. It is a carefully engineered process that requires understanding the failure mode, selecting the right consumables and process parameters, and applying rigorous quality control. The result is not just a repaired roll but a roll that outperforms a new one, because the cladding can be tailored to the specific service conditions.
The paper also reminds me that the economics of repair versus replacement are not always obvious. A new roll might cost several million yuan and take months to deliver. A repair might cost a fraction of that and take weeks. The 2.54 times life improvement makes the repair route even more attractive, but only if the repair is done correctly. A failed repair is worse than no repair at all, because it costs time and money and may damage other equipment.
For engineers in the steel pipe and fitting industry, the lessons from this paper are directly transferable. We repair mandrels, rolls, and other heavy components using similar cladding techniques. The same principles of failure analysis, consumable selection, process control, and inspection apply. The paper is a good example of how to approach a repair problem systematically, and I would recommend it as a reference for anyone involved in heavy component repair.
5. Concluding Summary
The repair and strengthening of a φ1550mm backup roll by submerged arc cladding, as described in this paper, demonstrates that a well-engineered repair can extend component life well beyond that of a new part. The key factors are the correct selection of a low-crack-sensitivity welding wire, careful control of the cladding process parameters, and a properly designed post-weld heat treatment. The 2.54 times life improvement is a testament to the value of process discipline and the importance of understanding the failure mode before attempting a repair. For engineers in heavy industry, this paper is a practical guide to extending the life of expensive components and reducing downtime.
Zhuojin Pipe Fitting Co., Ltd