ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Effect of Shot Peening on Residual Stress and Microstructure of H08Mn2Si Cladding Layer

1. Literature Overview and the Role of Surface Treatment

This 2013 paper from the Academy of Armored Forces Engineering and the PLA 66295 unit examines the effect of shot peening on the residual stress and microstructure of an H08Mn2Si cladding layer. The authors used a pneumatic shot peening machine, X-ray diffraction to measure residual stress distribution with depth, and metallographic, microhardness, and surface roughness analysis to characterise the treated layer. The results show that shot peening creates a strengthening layer of about 500 μm, with microhardness increasing then decreasing, ferrite not transforming, and surface roughness increasing to varying degrees.

Shot peening is a surface treatment that I have specified for many components in the pipe and fitting industry. It is used to introduce compressive residual stress into the surface, which improves fatigue life and resistance to stress corrosion cracking. The paper is a good example of how shot peening affects a welded cladding layer, which is a different situation from peening a wrought or forged component.

2. Technical Analysis: Residual Stress and Microstructural Changes

The key result of the paper is the residual stress distribution. Shot peening introduces compressive residual stress at the surface, and this stress decreases with depth. The paper found a strengthening layer of about 500 μm, which is a typical depth for shot peening with standard parameters.

The microhardness profile is interesting. The paper reports that the microhardness increases then decreases with depth. This is typical of shot peening: the surface is work-hardened by the plastic deformation from the shot impacts, and the hardness is highest at the surface, decreasing with depth as the plastic strain decreases. However, the paper notes that the hardness increases then decreases, which suggests that there may be a peak hardness at some depth below the surface. This could be due to the interaction between the plastic deformation and the residual stress field.

The metallographic analysis shows that the ferrite does not transform. This is an important result. In some steels, shot peening can cause phase transformation, especially if the material is metastable austenite. H08Mn2Si is a low-alloy steel, and the cladding layer is likely to be ferritic or ferritic-pearlitic. The fact that the ferrite does not transform means that the strengthening is purely from work hardening and residual stress, not from a phase change.

The surface roughness increases after shot peening. This is expected, as the shot impacts create a rough surface. The paper notes that the roughness increases to varying degrees, which depends on the peening parameters. For applications where surface finish is important, this is a concern. However, for most fatigue-critical applications, the increase in surface roughness is acceptable because the compressive residual stress more than compensates for the roughness effect.

Property Before Shot Peening After Shot Peening Practical Significance
Surface residual stress Tensile or near-zero Compressive (typically -300 to -600 MPa) Improves fatigue life and stress corrosion resistance
Strengthening layer depth None ~500 μm Provides a protective layer against surface damage
Microhardness at surface Base hardness Increased (typically 10–30%) Indicates work hardening
Surface roughness As-clad Increased (Ra typically 3–6 μm) May require post-peening grinding for critical surfaces
Microstructure Ferrite/pearlite Ferrite/pearlite (no transformation) Strengthening is from work hardening, not phase change

3. Engineering Practice: What the Shop Floor Must Get Right

Shot peening is a simple process to describe but a difficult one to control. The key parameters are:

In the pipe and fitting industry, shot peening is used for:

The paper is a useful reference for these applications because it shows the effect of shot peening on a welded cladding layer. The cladding layer has a different microstructure from the base metal, and the shot peening response may be different. The paper shows that the ferrite does not transform, which is good news for the application of shot peening to low-alloy steel cladding.

4. Study Insights and Practical Implications

The paper is a good example of how surface treatment can be used to improve the performance of a welded component. The combination of cladding and shot peening is a powerful one: the cladding provides the required surface properties, and the shot peening introduces compressive residual stress to improve fatigue life.

One point that I would emphasise is the importance of controlling the surface roughness. The paper notes that the roughness increases after shot peening. For some applications, this is acceptable, but for others, it is not. If the component is in a flowing fluid, a rough surface can increase friction and turbulence. If the component is in a corrosive environment, a rough surface can provide sites for pitting. In these cases, the surface must be ground or polished after peening, but this must be done carefully to avoid removing the compressive layer.

Another point is the need for verification. Shot peening is a process that is easy to do badly. The intensity must be verified with Almen strips, and the coverage must be checked. I have seen components that were specified for shot peening but were not peened at all, because the supplier assumed that the process was not critical. The result was premature failure in service.

5. Concluding Summary

The effect of shot peening on the residual stress and microstructure of an H08Mn2Si cladding layer, as described in this paper, demonstrates that shot peening creates a strengthening layer of about 500 μm with compressive residual stress, increased microhardness, and no phase transformation. The increase in surface roughness is a concern for some applications but is generally acceptable for fatigue-critical components. For engineers in the pipe and fitting industry, the paper is a useful reference for the application of shot peening to welded cladding layers, particularly for drill pipe, tool joints, and high-pressure fittings where fatigue life and stress corrosion resistance are critical.