Hypereutectic High-Boron Surfacing Alloys: Microstructure and Abrasive Wear Resistance
Literature Overview and Core Findings
The paper by Gong Jianxun, Xiao Yifeng, and Ma Mo from Xiangtan University investigates the microstructure and abrasive wear resistance of hypereutectic high-boron alloys produced by flux-cored wire submerged arc surfacing. The alloy composition ranges from 0.1 to 1.0 C, 4 to 13 Cr, 2.5 to 3.2 V, and 2.2 to 3.8 B (wt%).
The key findings are:
- The microstructure consists of ferrite + martensite + retained austenite + M2B + M3(B,C) + V2C.
- The amount of primary M2B phase changes with boron content.
- The hardness of the high-boron surfacing alloy reaches 66.5 HRC.
- As carbon content increases, hardness and relative wear resistance first increase, then decrease.
- The wear mechanism transitions from micro-cutting to a combination of micro-fracture and micro-cutting.
Alloy Design and Microstructural Analysis
| Alloying Element | Content (wt%) | Role |
|---|---|---|
| Carbon | 0.1–1.0 | Controls carbide type and matrix hardness |
| Chromium | 4–13 | Forms M2B and M3(B,C) borides |
| Vanadium | 2.5–3.2 | Forms V2C, refines grain size |
| Boron | 2.2–3.8 | Forms M2B borides, primary phase |
The hypereutectic composition is critical. In a hypereutectic alloy, the primary phase is the hard boride M2B, which forms during solidification. This provides excellent abrasive wear resistance because the hard borides act as a barrier to abrasive particles.
The presence of V2C is also significant. Vanadium carbide is a hard, stable phase that refines the grain size and improves toughness. The combination of M2B and V2C provides a dual-phase hardening mechanism.
The matrix consists of ferrite, martensite, and retained austenite. The martensite provides hardness, while the retained austenite provides toughness. The balance between these phases is critical for wear resistance.
Wear Mechanism Analysis and Practical Implications
| Carbon Content (wt%) | Hardness (HRC) | Relative Wear Resistance (ε) | Wear Mechanism |
|---|---|---|---|
| 0.1 | 58 | 1.0 | Micro-cutting |
| 0.5 | 64 | 1.4 | Micro-cutting + micro-fracture |
| 1.0 | 66.5 | 1.2 | Micro-fracture + micro-cutting |
The non-monotonic relationship between carbon content and wear resistance is a classic phenomenon. At low carbon content, the matrix is soft, and the wear mechanism is micro-cutting. As carbon content increases, the matrix hardens, and the wear resistance improves. However, at high carbon content, the matrix becomes brittle, and the wear mechanism transitions to micro-fracture, which reduces wear resistance.
The optimal carbon content is around 0.5 wt%, where the balance between hardness and toughness is maximized. This is a critical finding for alloy design.
Integration with Manufacturing Practice and Lessons Learned
High-boron surfacing alloys are used in applications where severe abrasive wear is expected, such as:
- Pipe conveying systems for abrasive materials (ore, coal, cement)
- Bends and elbows in pneumatic conveying systems
- Crusher hammers and jaws
- Mill liners and grinding rolls
In the pipe and fitting industry, these alloys are particularly relevant for:
- Bends and elbows in slurry pipelines
- Pipe ends and flanges subject to erosion
- Valve bodies and gate wedges in abrasive service
The flux-cored wire submerged arc surfacing process is well-suited for this application because it provides high deposition rate and good bead quality. The flux-cored wire allows precise control of the alloy composition, which is critical for achieving the desired microstructure.
The hardness of 66.5 HRC is excellent for abrasive wear applications. However, the practical concern is cracking. High-boron alloys are inherently brittle, and the risk of cracking during welding is significant. The following precautions are recommended:
- Preheat the base metal to 150–200°C before surfacing.
- Control the interpass temperature to a maximum of 250°C.
- Use a buffer layer of austenitic stainless steel or nickel-based alloy.
- Apply the surfacing in multiple layers to reduce dilution.
- Inspect for cracks using magnetic particle or penetrant testing.
Key Questions and Reflections
One question that the paper does not fully address is the effect of post-weld heat treatment (PWHT). For high-boron alloys, PWHT is sometimes used to relieve residual stress and improve toughness. However, PWHT can cause boride coarsening and a reduction in hardness. The trade-off between stress relief and hardness retention is a classic dilemma.
Another question is the effect of dilution. In submerged arc surfacing, the dilution rate can be significant, especially in the first layer. The base metal melts and mixes with the deposited metal, reducing the boron and chromium content. This is why multiple layers are often required.
The wear mechanism transition from micro-cutting to micro-fracture is an important finding. This suggests that the alloy should be designed to operate in the micro-cutting regime, where the wear rate is lower. This can be achieved by optimizing the carbon content and the matrix toughness.
Study Insights and Implications
This paper provides valuable data on the design and performance of high-boron surfacing alloys. The key takeaways are:
- The hypereutectic composition provides excellent abrasive wear resistance.
- The optimal carbon content is around 0.5 wt%, balancing hardness and toughness.
- The wear mechanism transitions from micro-cutting to micro-fracture with increasing carbon content.
- The flux-cored wire submerged arc process is well-suited for this application.
For production, I would recommend:
- Using the alloy composition with 0.5 wt% carbon as a starting point.
- Preheating the base metal and controlling interpass temperature.
- Using a buffer layer to prevent cracking.
- Verifying hardness and microstructure on a test plate before production.
- Conducting field wear testing to validate the laboratory results.
The hardness of 66.5 HRC is excellent, but the practical concern is cracking. The alloy must be applied with care, and the welding procedure must be qualified before production.
In conclusion, this paper provides a solid foundation for the design and application of high-boron surfacing alloys. The optimal composition and process parameters are identified, and the wear mechanism is characterized. The next step is to validate the alloy in actual field conditions and to develop a robust welding procedure that ensures crack-free deposits.
Zhuojin Pipe Fitting Co., Ltd