ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Development of a New High-Manganese Steel Surfacing Electrode: A Practical Approach to Reducing Fume Emissions

Literature Overview

This work by Cong Guozhi and Chen Chunhuan from Dalian Jiaotong University addresses a persistent problem in the welding industry: the high fume generation rate of high-manganese steel electrodes. High-manganese steel, typically containing 12 to 14% manganese, is widely used for surfacing applications on components subject to severe impact and abrasive wear, such as railway crossings, crusher jaws, and shovel teeth. However, the conventional electrodes used for this application produce excessive welding fumes, which create a health hazard for welders and contribute to environmental pollution. The authors propose a novel approach: using an austenitic steel wire as the core wire and a low-hydrogen type coating. Through a series of experiments, they developed a new electrode that meets all the required performance criteria while significantly reducing fume generation.

Interpretation of Technical Points

The Fume Generation Problem in High-Manganese Steel Electrodes

The high fume generation rate in conventional high-manganese steel electrodes is primarily due to the composition of the coating. Traditional coatings for these electrodes contain significant amounts of manganese-bearing compounds, such as ferromanganese and manganese oxide, which are added to compensate for manganese loss during the welding arc. When the arc is struck, these compounds volatilize and oxidize in the arc atmosphere, forming fine particles of manganese oxide that constitute a large portion of the fume. Prolonged exposure to these fumes can lead to manganism, a neurological condition similar to Parkinson's disease, and is a serious occupational health concern.

The Proposed Solution: Austenitic Core Wire with Low-Hydrogen Coating

The authors' key innovation is to shift the source of manganese from the coating to the core wire. By using an austenitic steel wire that already contains the required amount of manganese, the coating can be formulated without the need for large additions of manganese-bearing compounds. The coating is then designed as a low-hydrogen type, which typically contains calcium fluoride, calcium carbonate, and small amounts of deoxidizers and alloying elements. This approach has two advantages. First, it reduces the amount of manganese in the coating that can volatilize into the fume. Second, the low-hydrogen coating produces a more stable arc and better weld metal properties.

Experimental Results and Performance Evaluation

The authors conducted a series of tests to evaluate the performance of the new electrode. The key results are summarized in the table below:

Parameter Conventional Electrode New Electrode
Core Wire Composition High-Manganese Steel Austenitic Steel with Mn
Coating Type Manganese-Bearing Low-Hydrogen
Fume Generation Rate (g/kg) 18.5 9.2
Weld Metal Hardness (HRC) 38 36
Weld Metal Impact Toughness (J) 28 32
Weld Metal Mn Content (%) 13.5 13.2
Arc Stability Good Excellent
Slag Detachability Fair Good

The new electrode achieves a 50% reduction in fume generation rate while maintaining comparable hardness and slightly improving impact toughness. The manganese content of the weld metal is essentially the same, confirming that the core wire provides sufficient manganese to achieve the desired alloy composition. The arc stability is improved, and the slag is easier to remove, which improves welder productivity.

Integration with Engineering Practice

Application Context in Our Industry

In the steel pipe and pipe fitting industry, high-manganese steel surfacing is used for a variety of components, including the grizzly bars in scrap handling, the rolls in pipe straightening machines, and the teeth of excavator buckets used in material handling. These components are subject to severe impact and abrasion, and the surfacing layer must be both hard and tough. The conventional electrodes used for this application have been a source of concern for our welders, who often complain about the heavy fume generation and the associated health risks.

Practical Considerations for Electrode Selection

When selecting an electrode for high-manganese steel surfacing, several factors must be considered beyond just fume generation. The electrode must produce a weld metal with the correct composition, typically 12 to 14% manganese and 0.8 to 1.2% carbon, to achieve the desired austenitic structure. The weld metal must also have sufficient toughness to resist cracking under impact loading. The electrode must be capable of being used in all positions, as many components require out-of-position welding. The new electrode developed by the authors appears to meet all these requirements.

Welding Procedure Development

The introduction of a new electrode requires the development of a new welding procedure specification (WPS). In our experience, the following parameters are typical for high-manganese steel surfacing:

Parameter Typical Range
Welding Current (A) 180-220
Arc Voltage (V) 24-28
Welding Speed (cm/min) 25-35
Preheat Temperature (°C) 150-200
Interpass Temperature (°C) 200-250
Electrode Diameter (mm) 4.0 or 5.0
Polarity DC Reverse (DCEP)

The preheat and interpass temperature control is critical for high-manganese steel because the material is sensitive to cracking if the temperature is too low. However, excessive interpass temperatures can lead to carbide precipitation and embrittlement. The new electrode's low-hydrogen coating helps reduce the risk of hydrogen-induced cracking, which is a common problem with high-manganese steel welds.

Health and Safety Considerations

The reduction in fume generation is not just a comfort issue; it is a serious health and safety concern. Manganese fumes are classified as a hazardous substance, and the Occupational Safety and Health Administration (OSHA) has established a permissible exposure limit of 0.2 mg/m³ for manganese. In practice, many welding operations exceed this limit when using conventional high-manganese steel electrodes. The new electrode, with its 50% reduction in fume generation, can significantly reduce the exposure levels and help facilities comply with regulations.

Case Study from Our Shop Floor

We introduced a similar type of low-fume high-manganese steel electrode in our pipe straightening roll surfacing operation. The rolls are 800 mm in diameter and 1200 mm long, and they are surfaced with a 10 mm thick layer of high-manganese steel. Previously, our welders would complete one roll in approximately 8 hours, with a fume extraction system running continuously. The welders complained of headaches and metallic taste in their mouths after a full day of welding. After switching to the low-fume electrode, the welders reported a significant improvement in their working conditions, and the fume extraction system was able to maintain a cleaner work environment. The weld quality was also improved, with fewer slag inclusions and better surface finish.

Key Questions and Reflections

Is the Low-Hydrogen Coating Suitable for All Applications?

The low-hydrogen coating is generally recommended for high-strength steels and for applications where hydrogen-induced cracking is a concern. However, low-hydrogen electrodes require careful storage and handling to prevent moisture absorption. If the electrode is exposed to humidity for an extended period, the coating can absorb moisture, which will reintroduce hydrogen into the weld metal. In our experience, low-hydrogen electrodes should be stored in a heated cabinet at 100 to 150°C and used within 4 hours of removal from the cabinet. This requires a disciplined approach to electrode management on the shop floor.

What Are the Economic Implications?

The new electrode may have a slightly higher cost than conventional electrodes due to the use of austenitic steel wire as the core. However, the improved arc stability and slag detachability can lead to higher deposition rates and reduced cleaning time, which can offset the higher material cost. In our experience, the total cost per kilogram of deposited weld metal is often comparable, and the health benefits and improved working conditions provide additional value that is difficult to quantify but is nonetheless important.

Where Do Standards Leave Room for Judgment?

The relevant standards for surfacing electrodes, such as AWS A5.13 and GB/T 984, specify the chemical composition and mechanical properties of the deposited weld metal. However, they do not specify limits on fume generation. This leaves the electrode manufacturer with considerable latitude in designing the coating to minimize fume generation while meeting the required performance. The engineer must therefore evaluate the fume generation characteristics of an electrode as part of the qualification process, even though it is not explicitly required by the standard.

Study Insights and Implications

This study demonstrates that innovative thinking can solve a persistent problem in the welding industry. By shifting the source of manganese from the coating to the core wire, the authors have developed an electrode that meets all the required performance criteria while significantly reducing fume generation. This is a classic example of how a simple change in design can have a major impact on health, safety, and environmental performance.

For engineers in our industry, this study highlights the importance of considering the entire welding system, not just the weld metal properties. The coating composition has a direct impact on fume generation, arc stability, and slag behavior, all of which affect welder health and productivity. The next time we are faced with a welding problem, we should consider whether the solution lies in a different approach to the electrode design, rather than just adjusting the welding parameters.

Reference Value and Outlook

This literature is of direct reference value to our industry, particularly for surfacing operations where high-manganese steel is used. The approach of using an austenitic core wire with a low-hydrogen coating can be applied to other alloy systems as well. For example, we have seen similar approaches used to reduce fume generation in stainless steel electrodes and nickel-based alloy electrodes.

Looking forward, there is a need for more research on the long-term health effects of welding fume exposure and on the development of even lower fume generation electrodes. The use of automated welding processes, such as robotic welding and submerged arc welding, can also help reduce fume exposure by removing the welder from the immediate vicinity of the arc. However, for manual welding operations, the development of low-fume electrodes is a critical step forward.

In conclusion, this study provides a practical solution to a significant health and safety problem in the welding industry. The new electrode meets all the required performance criteria while reducing fume generation by 50%. This is a significant achievement that can have a direct impact on the health and well-being of welders, and it is a development that should be embraced by our industry.