ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Composite Hardfacing Liners for Blast Furnace Receiving Hoppers and Distributors: A Practical Review

Background and the Wear Problem

I have spent enough years around blast furnaces to know that the receiving hopper and the distributor are not glamorous components, but they take a beating that would make most structural engineers wince. The original design in this paper used Mn13 austenitic manganese steel liners, which is the classic choice for impact and abrasion resistance in ore handling. The problem is that Mn13 work-hardens only under high impact loads; in a hopper where the burden is mostly fines and small lump ore, the impact energy is insufficient to trigger the dislocation-based hardening mechanism, so the liner simply wears away by abrasion at a rate that no one can accept. The paper reports that the original Mn13 liners had a service life that was simply too short, and the authors set out to develop a composite liner system that could survive the combined abrasion and moderate impact environment of a blast furnace top.

The Composite Liner Design

The new liner construction is straightforward in concept but demanding in execution. The base plate is either cast steel or Q235 structural steel, which provides the structural rigidity and the attachment points for bolting or welding into the hopper shell. Onto this base, a hardfacing alloy is applied by adhesive bonding and welding, and then TiC-steel strip blocks are inset into the hardfacing layer. The TiC-steel strip blocks are the real wear-resistant element; titanium carbide particles embedded in a steel matrix give a hardness that can exceed 60 HRC, and the carbide particles resist abrasive wear far better than any single-phase steel matrix. The hardfacing alloy serves as a matrix that holds the blocks in place and provides a degree of toughness to absorb the impact of falling burden.

The key metallurgical insight here is that the composite liner does not rely on work hardening at all. It relies on the intrinsic hardness of the TiC particles, which are thermodynamically stable and will not soften or decompose at the operating temperatures of a blast furnace top, typically in the range of 150 to 300 °C. The base plate provides the weldability and the mechanical attachment, while the hardfacing and the inserts provide the wear resistance. This is a classic case of designing the composite so that each layer does what it does best, rather than trying to make one material do everything.

Metallurgical and Process Considerations

Parameter Mn13 Liner Composite Liner
Base material Mn13 austenitic manganese steel Cast steel or Q235
Wear mechanism Abrasion with insufficient work hardening Abrasion resistance from TiC particles
Hardness (as-worn) ~200 HB (unhardened) 55-62 HRC (TiC inserts)
Impact resistance Good under high impact Moderate, adequate for hopper service
Weldability Difficult, requires controlled heat input Good on Q235 base
Service life (relative) 1.0 5.0 - 8.0

The welding of the hardfacing alloy onto the base plate is the critical process step. The authors do not specify the exact welding process in the abstract, but from my experience with similar composite liners, the hardfacing is typically applied by submerged arc welding (SAW) or flux-cored arc welding (FCAW) with a hardfacing wire that deposits an alloy in the range of 15 to 30 percent chromium and 3 to 5 percent carbon, giving a deposit hardness of 55 to 60 HRC. The TiC-steel strip blocks are then inset into the hardfacing layer while it is still hot, or they are pre-placed and the hardfacing is deposited around them. The critical issue is ensuring that the blocks are securely bonded; if there is any gap between the block and the matrix, the block will loosen and fall out, and the liner will fail catastrophically.

Field Results and Economic Impact

The paper reports that the new composite liners achieved a service life of 5 to 8 times that of the original Mn13 liners. From a plant manager's perspective, this is not just a wear life improvement; it is a reduction in downtime. Every time the receiving hopper or the distributor has to be shut down for liner replacement, the blast furnace is either slowed or taken off line, and the cost of lost production in a modern integrated steel plant can easily exceed the cost of the liners themselves by an order of magnitude. A 5 to 8 times improvement in liner life means that the maintenance interval can be extended from, say, every 6 months to every 3 to 4 years, which is a significant operational and scheduling advantage.

There is also the safety angle. Working inside a blast furnace top is not a pleasant job; it is hot, dusty, and confined, and every time we send a crew in there, we are exposing them to risk. Reducing the frequency of liner replacement directly reduces the number of confined space entries and the associated risk exposure. This is a point that is often overlooked in technical papers but is very much on the mind of anyone who has had to sign off on a confined space entry permit.

Lessons and Recommendations

From my years on the plant floor, I would add a few practical notes to this paper's findings. First, the TiC-steel strip blocks must be checked for dimensional consistency before assembly. If the blocks vary in thickness by more than 0.5 mm, the hardfacing will not cover them uniformly, and the exposed edges will wear preferentially, leading to premature block loss. Second, the hardfacing alloy must be selected for its ability to bond with the TiC blocks. Some hardfacing alloys have poor wetting characteristics with TiC, and the bond will be purely mechanical rather than metallurgical, which is a recipe for failure under thermal cycling. Third, the base plate should be preheated before hardfacing to prevent hydrogen-induced cracking in the heat-affected zone, particularly if the base is a cast steel with higher carbon content.

The paper is a good example of applied engineering that solves a real problem with a practical, cost-effective solution. It does not break new scientific ground, but it delivers a 5 to 8 times improvement in service life, which is what the plant manager cares about. I would recommend this approach to any operation that handles abrasive bulk materials in a moderate impact environment, and I would encourage the maintenance team to track the wear profile of the composite liners carefully so that the replacement interval can be optimized based on actual data rather than on a fixed schedule.