ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Plasma Surfacing of Exhaust Valves with High-Strength Alloy Powder: Residual Stress and Deformation Analysis

Overview and Background

The paper by Yang Xinglin and colleagues from Jiangsu University of Science and Technology and Nanjing COSCO Marine Equipment Co., Ltd. addresses a topic that is critical for marine engines: the surfacing of exhaust valves with high-strength alloy powder. Exhaust valves in marine diesel engines operate at high temperatures and are subjected to severe thermal and mechanical loads. The valve seat area is particularly vulnerable to wear and corrosion, and it is often surfaced with a hard, wear-resistant alloy. Plasma surfacing is a common process for this application because it provides a high-quality deposit with low dilution and good control over the bead shape. However, the welding process introduces residual stresses and deformation, which can affect the valve's performance and service life. The paper uses ABAQUS finite element software to simulate the residual stress and deformation of the valve during plasma surfacing, and it validates the simulation results with experimental measurements.

Simulation Methodology and Material Modeling

The paper uses ABAQUS to simulate the plasma surfacing process. The key challenge is to model the material behavior of the alloy powder, which undergoes a phase change during melting and solidification. The paper addresses this by using a UMATHT subroutine, which allows the material properties to be defined as a function of temperature and state. The material is defined in different states based on its melting point, and the material parameters are written into the subroutine. This is a sophisticated approach that captures the nonlinear behavior of the material during the phase change. The simulation likely uses a moving heat source to model the plasma arc, and it calculates the temperature field, the stress field, and the deformation.

Results and Discussion

The paper's results show that the residual stress calculated using the UMATHT subroutine agrees well with the experimental measurements. This validates the simulation approach and demonstrates that the UMATHT subroutine is an effective way to model the material behavior. The results also show that the residual stress is significantly affected by the material properties, and that the residual stress in the thickness direction and the axial direction is roughly symmetric about the weld centerline. This symmetry is expected for a circular valve, but it is a useful confirmation of the model's accuracy. The paper also shows that the deformation of the weld is larger than the deformation of the base material, but the overall deformation is small. The maximum deformation is located at the middle of the weld, which is consistent with the thermal expansion and contraction of the weld metal.

Practical Implications for Valve Manufacturing

The paper's findings have direct implications for the manufacturing of exhaust valves. The residual stress in the valve can affect its dimensional accuracy and its fatigue life. If the residual stress is too high, the valve may distort during machining or fail in service. The paper's finding that the residual stress is symmetric about the weld centerline suggests that the welding process is well-controlled, but it also highlights the importance of maintaining a consistent heat input. The deformation of the weld is small, but it must be accounted for in the final machining operation. The paper's use of numerical simulation to predict the residual stress and deformation allows the manufacturer to optimize the welding process before it is implemented in production.

Key Questions and Reflections

One question that the paper raises is the effect of the welding sequence on the residual stress distribution. In a real valve, the surfacing is applied in a circular pattern, and the sequence of deposition affects the residual stress. The paper's model likely assumes a single pass, which may not capture the effects of multiple passes. Another question is the effect of the post-weld heat treatment. The paper does not address this, but in practice, exhaust valves are often stress-relieved after welding to reduce residual stress. The optimal stress relief temperature and time must be determined experimentally.

Study Insights and Implications

The most important insight from this paper is that numerical simulation can be used to predict the residual stress and deformation in a welded component, provided that the material behavior is modeled correctly. The UMATHT subroutine is a powerful tool for this purpose, and the paper demonstrates its effectiveness. The implication for the industry is that numerical simulation can reduce the number of trial-and-error experiments and allow manufacturers to optimize the welding process before it is implemented. The paper's approach of validating the simulation results with experimental measurements is a good model for any welding simulation study.

Reference Value and Outlook

This paper is a valuable reference for anyone involved in the welding of high-temperature components, such as exhaust valves, turbine blades, and nozzles. It provides a methodology for simulating the residual stress and deformation during plasma surfacing, and it highlights the importance of accurate material modeling. The findings are specific to the exhaust valve geometry and the alloy powder material, but the methodology can be applied to other components and materials. The outlook is that numerical simulation will become more common in the welding industry as computational power increases and software becomes more accessible. The paper provides a good example of how to apply this technology to a real manufacturing problem.