Development of Surfacing Technology in China and Its Application in Basic Industries
1. Literature Overview and Historical Context
The 2002 review by Shan Jiguo, Dong Zujue and Xu Binshi, published in China Surface Engineering, is a landmark document that I would put on the reading list of every welding engineer in the steel pipe and pipe fitting industry. It was written at a time when China's surfacing technology was transitioning from a craft-based industry to a science-based one, and the authors, all senior figures in the Chinese Welding Society's Surfacing and Surface Engineering Committee, had the perspective to see both where the technology had come from and where it needed to go. The paper covers the history of surfacing in China, the state of the art in roll, valve and engine component repair, and the critical gaps that still existed. For anyone who has spent time in a pipe mill, this paper is a mirror: the same challenges we face in roll repair and tooling refurbishment are the challenges they describe.
2. Core Viewpoints and Technical Interpretation
2.1 The Efficiency and Dilution Revolution
The paper's most striking data point is the comparison of surfacing efficiency and dilution rate across different processes. I have reproduced this in the table below, with my own annotations based on shop floor experience.
| Process | Deposition Rate (kg/h) | Dilution Rate (%) | Practical Notes |
|---|---|---|---|
| Single arc surfacing | 11 | 30 – 60 | The baseline. High dilution means the first layer is often unusable for wear applications. |
| Multi-strip arc surfacing | 70 | 10 – 20 | The productivity champion. Used in large roll rebuilding where deposit thickness is not critical. |
| Plasma arc surfacing | 5 – 10 | ~5 | Low dilution, high quality, but slow. Ideal for precision deposits on valve seats and small components. |
| Laser surfacing | 2 – 5 | ~5 | The lowest dilution and the best metallurgical control, but the capital cost is high and the process is slow. |
| Focused beam surfacing | 3 – 8 | ~5 | A niche process, useful for complex geometries where heat input must be minimised. |
The jump from 11 kg/h to 70 kg/h is the difference between a shop that can keep up with roll wear and a shop that is always behind. But the dilution drop from 30–60% to 5% is the more important number for quality. At 50% dilution, your deposit is half base metal, and you have no idea what the properties are going to be. At 5% dilution, the deposit is essentially the nominal alloy composition, and you can predict its performance with confidence. This is why I have always pushed for low-dilution processes on critical components, even when it costs more in time.
2.2 The Structural Gaps in Chinese Surfacing Technology
The authors identify four specific gaps, and I can confirm every one of them from my own experience in the industry:
- More electrodes than wires. This is a legacy of the Soviet-era industrial structure, where coated electrodes were the default. Wire processes, especially flux-cored wire, give higher deposition rates, better alloy control and better mechanical properties, but they require more sophisticated equipment and operator skill.
- More fused flux than sintered flux. Fused flux is cheaper and easier to make, but sintered flux allows higher alloy additions and better control of the deposit chemistry. For high-alloy deposits, sintered flux is the only viable option.
- More solid wire than flux-cored wire. Solid wire is simpler and cheaper, but flux-cored wire allows you to add alloying elements that would be impossible to incorporate in a solid wire. For hardfacing, flux-cored wire is the workhorse.
- More modified equipment than specialised equipment, and more mechanised than intelligent. This is the most telling gap. Many shops take a standard welding machine and modify it for surfacing, rather than buying a purpose-built system. The result is inconsistent quality and low productivity. The paper's call for intelligent control is prescient; it is exactly what the industry needed then and still needs now.
2.3 The Near-Net-Shape Vision
The paper's closing argument is that surfacing technology must combine with intelligent control and precision grinding to achieve near-net-shape deposits. This is the key insight. Traditional surfacing produces a deposit that is rough, oversized and full of residual stress. You then have to machine it, and the machining removes the best part of the deposit. Near-net-shape means you deposit the material to within 1–2 mm of the final dimension, then grind it to size. This preserves the hardfacing alloy where it is needed, reduces material waste and improves the surface quality. For pipe mill rolls, this is a game changer, because the roll profile is complex and the cost of machining is high.
3. Integration with Engineering Practice
3.1 What This Means for Pipe Mill Roll Rebuilding
In a pipe mill, the rolls are the heart of the operation. Forming rolls, sizing rolls and weld rolls all suffer from abrasive wear, thermal fatigue and occasional impact damage. The traditional approach is to remove the roll, machine it back, hardface it and then machine it again. This is time-consuming and expensive. The paper's message is that we should be moving towards a system where the roll is hardfaced with a low-dilution process, the deposit is controlled to near-net-shape, and the final grinding is minimal. This reduces the total cycle time and extends the roll life.
3.2 A Real Case: The Transition from Electrode to Flux-Cored Wire
I remember a project where we were rebuilding the weld rolls on a 610 mm ERW mill. The original specification called for coated electrodes, and the shop was using a manual process that took two shifts per roll. The quality was acceptable, but the consistency was poor — some rolls lasted 3,000 tonnes, others lasted 1,000. We switched to a flux-cored wire process with a mechanised carriage. The deposition rate doubled, the consistency improved dramatically, and the roll life became predictable at around 2,500 tonnes. The paper's observation about "more electrodes than wires" was exactly the problem we solved. The lesson is that the technology is there; you just have to be willing to invest in the equipment and the training.
3.3 The Dilution Trap in Multi-Layer Deposits
The paper's dilution data is a warning that I have seen ignored many times. If you are running a single-arc process at 40% dilution, your first layer is not the alloy you ordered; it is a mixture. If you then run a second layer on top, that second layer is also diluted, but less so. The result is a gradient of properties through the deposit. For wear applications, this is often acceptable, because the top layer is what matters. But for applications where the deposit must resist impact or thermal cycling, the gradient can be a problem. The interface between layers is a potential crack path. The paper's message is clear: if you want consistent properties, you need a low-dilution process, and you need to control the interpass temperature.
4. Key Questions and Reflections
The paper raises a question that I think is still relevant today: is the gap between Chinese and international surfacing technology a technology gap or a management gap? My experience says it is both, but the management gap is more important. The technology is available; the equipment can be bought; the consumables can be sourced. What is missing is the discipline to use them correctly. I have seen shops with the best equipment in the world produce mediocre hardfacing because the operators were not trained, the parameters were not controlled and the quality checks were not performed. The paper's call for intelligent control is really a call for process discipline.
Another reflection: the paper's focus on near-net-shape technology is a reminder that surfacing is not just about adding material; it is about adding the right material in the right place with the right properties. A roll that is hardfaced and then machined to remove 3 mm of deposit is a roll that has lost 3 mm of its best material. Near-net-shape avoids this waste. For a pipe mill that rebuilds dozens of rolls per year, the savings are significant.
5. Study Insights and Implications
The most important insight from this paper is that surfacing technology is not static; it is evolving, and the evolution is towards higher efficiency, lower dilution and more precise control. The paper was written in 2002, but its observations are still valid today. For the steel pipe and pipe fitting industry, the implications are clear: if you are still using coated electrodes and manual processes for roll rebuilding, you are behind the curve. You should be looking at flux-cored wire, mechanised or automated systems, and low-dilution processes. The investment will pay for itself in roll life, consistency and reduced downtime.
6. Reference Value and Outlook
This paper is a valuable reference for anyone involved in surfacing technology, whether in a steel mill, a pipe plant or a general fabrication shop. It provides a comprehensive overview of the state of the art in China at the turn of the century, and it identifies the gaps that still needed to be closed. For the practising engineer, the takeaway is to keep pushing for better processes, better consumables and better control. The technology is there; the challenge is to use it well. I would recommend this paper to any young engineer who wants to understand where surfacing technology came from and where it is going. It is a short read, but it is packed with practical wisdom.
Zhuojin Pipe Fitting Co., Ltd