Surfacing Repair of Die Forging Hammer Head Dovetail Groove
1. Literature Overview and Practical Context
This brief technical note by Zhou Haiyan from Chongqing Nantong Mining Bureau Machinery Factory addresses a specific but critical maintenance problem: the repair of dovetail grooves on steam-air die forging hammer heads. These grooves, which secure the hammer head to the ram, experience severe impact loading exceeding 5000 Joules per blow, leading to surface damage in the form of grooves, indentations, and deformation.
From my years in the forging industry, I can tell you that the dovetail groove is one of the most critical and highly stressed areas of a forging hammer. It must transmit the full impact force from the ram to the die, and any damage can lead to catastrophic failure if not addressed promptly. The repair of these grooves is a specialized skill that requires careful consideration of the base material, the welding process, and the post-repair heat treatment.
The author's approach is straightforward: build up the damaged dovetail groove surface by surfacing welding, then machine it back to the original dimensions. However, the success of this repair depends on many factors that are not fully detailed in this brief note.
2. Technical Analysis of the Repair Process
2.1 Failure Mechanism of the Dovetail Groove
The dovetail groove fails through a combination of mechanisms:
- Impact Fatigue: The repeated impact loading causes surface deformation and work hardening, eventually leading to fatigue crack initiation.
- Abrasive Wear: The relative movement between the hammer head and the ram causes abrasive wear, creating grooves and indentations.
- Thermal Cycling: The hammer head is heated by the forging process and cooled by the environment, causing thermal fatigue.
2.2 Repair Strategy
The repair process typically involves the following steps:
| Step | Operation | Key Considerations |
|---|---|---|
| 1 | Pre-repair inspection | Visual, MT, UT to assess damage extent |
| 2 | Preheating | 200-300°C to prevent cracking |
| 3 | Surface preparation | Grinding or machining to remove damaged material |
| 4 | Surfacing welding | Low hydrogen process, controlled interpass temperature |
| 5 | Post-weld heat treatment | Stress relief at 300-400°C |
| 6 | Machining | Restore original dimensions |
| 7 | Post-repair inspection | MT, UT, hardness testing |
2.3 Welding Process Selection
For repairing dovetail grooves on hammer heads, I would recommend:
- Shielded Metal Arc Welding (SMAW) with low hydrogen electrodes (E7018 or E8018).
- Gas Metal Arc Welding (GMAW) with solid wire for higher deposition rates.
- Flux Cored Arc Welding (FCAW) for better penetration and deposition efficiency.
The electrode/wire selection is critical. The repair material should have:
- Sufficient strength to withstand impact loading.
- Good toughness to resist fatigue crack propagation.
- Weldability compatible with the base material (typically medium carbon or low alloy steel).
3. Engineering Practice Considerations
3.1 Preheating and Interpass Temperature
Preheating is essential for this application because:
- The hammer head is a large, massive component that acts as a heat sink.
- The high carbon equivalent of the base material increases crack susceptibility.
- The dovetail groove geometry creates high restraint, increasing residual stresses.
I recommend:
- Preheat temperature: 200-300°C (depending on carbon equivalent).
- Interpass temperature: 250-350°C (not exceeding 400°C).
- Use temperature-indicating crayons or infrared thermometers for monitoring.
3.2 Welding Technique
The welding technique should be carefully controlled to minimize distortion and residual stresses:
- Use a "butterfly" or "back-step" technique to distribute heat evenly.
- Peen each weld pass to relieve residual stresses.
- Use multiple thin passes rather than a few thick passes.
3.3 Post-Weld Treatment
After welding, the repair should be:
- Cooled slowly (in still air, not quenched).
- Stress-relieved at 300-400°C for 2-4 hours.
- Inspected for cracks using MT or UT before machining.
4. Critical Evaluation and Study Insights
This brief note provides a basic overview of the repair process but lacks the detailed technical information that would be valuable for engineers. Based on my experience, I have several observations:
- Lack of Detail: The note does not specify the welding consumables, preheat temperature, or post-weld heat treatment parameters. This information is critical for successful repairs.
- Quality Control: The note does not mention inspection requirements. I would recommend:
- 100% MT on the repaired surface.
- UT for subsurface defects.
- Hardness testing to verify the repair material's properties.
- Repair vs. Replacement: The economic decision between repair and replacement depends on:
- The extent of damage.
- The cost of a new hammer head.
- The downtime required for repair vs. replacement.
- Documentation: Proper documentation of the repair process is essential for traceability and quality assurance.
5. Conclusions and Recommendations
The surfacing repair of dovetail grooves on die forging hammer heads is a viable and cost-effective solution for extending the service life of these critical components. However, the success of the repair depends on careful process control, including preheating, welding parameters, and post-weld treatment.
For engineers performing this type of repair, I recommend:
- Develop a detailed repair procedure with specific parameters.
- Qualify the welding procedure with a mock-up test.
- Implement strict quality control including NDT and hardness testing.
- Document the repair and monitor the component's performance after repair.
This approach can significantly extend the service life of forging hammers and reduce maintenance costs, but it requires a thorough understanding of the failure mechanisms and the metallurgical considerations involved.
Zhuojin Pipe Fitting Co., Ltd