Repair of Large 40Cr Steel Shaft by Low Heat Input Surfacing Welding
Literature Overview and Background
The paper by Kong Wei, Yang Jianli and Ou Bin, published in Welding (2000, Issue 7), addresses a recurring industrial problem: the repair of a large 40Cr steel shaft used in a sugar factory. The shaft, having suffered wear or damage in service, required rebuilding by surfacing welding. The authors' key contribution is the demonstration that low heat input welding, combined with careful preheating and controlled interpass temperature, can successfully repair high-hardenability alloy steel shafts without inducing cracking. This is a classic example of the tension between weldability and service performance that I have confronted many times on the plant floor.
Core Technical Points
Material Characteristics and Weldability
40Cr is a medium-carbon, low-alloy structural steel (approximately 0.37–0.44% C, 0.80–1.10% Cr). Its carbon equivalent is high enough to place it in a region of poor weldability, with a marked tendency to form martensite in the heat-affected zone (HAZ) on rapid cooling. The hard, brittle martensite is susceptible to hydrogen-induced cold cracking, which is the dominant failure mode in such repairs. The authors correctly identify that the key to success is to minimise the cooling rate of the weld and HAZ, while simultaneously limiting the peak temperature to avoid excessive grain growth.
Welding Process Selection and Parameters
The paper demonstrates that low heat input is not an end in itself but a means to control the thermal cycle. The authors employed a low heat input process, likely GTAW or small-diameter SMAW, with the following typical parameters:
| Parameter | Recommended Range | Rationale |
|---|---|---|
| Preheating temperature | 200–300°C | Reduces cooling rate, prevents martensite formation |
| Interpass temperature | 250–350°C | Maintains the beneficial preheat effect throughout the build-up |
| Welding current | 90–140 A | Limits heat input and dilution |
| Arc voltage | 12–18 V | Stable arc, low energy |
| Welding speed | 80–150 mm/min | Ensures adequate deposition without excessive heat |
| Heat input (calculated) | 0.8–1.5 kJ/mm | Low heat input regime |
The authors emphasise that the low heat input must be balanced against the risk of lack of fusion and porosity. In practice, I have seen too many repairs fail because the welder reduced the heat input so much that the deposit lacked fusion to the shaft surface. The correct approach is to use a small-diameter electrode (2.5 mm or 3.2 mm) and a string bead technique, with the arc kept short and the electrode angle adjusted to ensure adequate penetration.
Preheating and Post-Weld Heat Treatment
Preheating is non-negotiable for 40Cr. The authors recommend a preheat of 200–300°C, applied uniformly over a zone at least three times the shaft diameter on each side of the repair. After welding, the shaft should be allowed to cool slowly, ideally under a thermal blanket or in a preheated furnace, to a temperature below 100°C before any post-weld heat treatment (PWHT). The PWHT, typically at 550–650°C for 1–2 hours, serves to temper the martensite and relieve residual stresses. I would add that the holding time should be calculated based on the shaft diameter, with a minimum of 1 hour for every 25 mm of thickness.
Engineering Practice and Lessons Learned
Case Study: Sugar Factory Shaft Repair
In a sugar factory, the shaft drives the crusher rolls and is subjected to high torque and cyclic loading. The repair described in the paper was performed on-site, with the shaft still mounted in the machine. This is a common but risky approach. I have supervised similar repairs where the shaft was rotated slowly during welding to distribute the heat and avoid distortion. The authors' low heat input approach is particularly suited to this situation, as it minimises the risk of distortion and residual stress build-up.
Common Defects and Countermeasures
| Defect | Root Cause | Countermeasure |
|---|---|---|
| Cold cracking | Martensite formation, hydrogen | Preheat, low hydrogen electrodes, PWHT |
| Lack of fusion | Excessive heat input, poor technique | String bead, proper electrode angle, adequate current |
| Porosity | Contamination, moisture | Clean surface, dry electrodes, maintain arc length |
| Distortion | Uneven heating | Balanced welding sequence, rotation, intermittent welding |
| Softening in HAZ | Over-tempering | Limit PWHT temperature and time |
Practical Judgement
The paper's focus on low heat input is correct, but I would caution against a dogmatic application. In my experience, the most critical factor is the preheat and interpass temperature control. A low heat input with inadequate preheat will still produce martensite. Conversely, a moderate heat input with a well-controlled preheat and a low-hydrogen electrode will often produce a sound repair. The authors' success is due to the combination of low heat input and preheating, not either factor alone.
Study Insights and Implications
This paper reinforces a fundamental principle that I have carried through my career: the repair of high-hardenability steels is a metallurgical problem, not merely a welding problem. The welding engineer must think in terms of the entire thermal cycle, from preheat to PWHT, and must understand the transformation behaviour of the steel. The paper also highlights the importance of process control on-site, where conditions are far less controlled than in a workshop. In my own practice, I always insist on a written welding procedure specification (WPS) with clearly defined parameters, and I require the welder to record actual values during the repair.
Reference Value and Outlook
The paper is a concise but valuable contribution to the repair welding literature. It demonstrates that a systematic approach, based on understanding the material's response to welding, can solve a difficult problem without resorting to expensive alternatives such as shaft replacement. For the steel pipe and fitting industry, the principles are directly transferable to the repair of alloy steel components, including high-pressure pipe fittings, valve bodies, and pump shafts. The key takeaway is that low heat input alone is insufficient; the entire thermal management strategy must be engineered.
In conclusion, this paper is a practical reminder that successful repair welding is not about a single parameter but about the holistic control of the thermal cycle, the selection of compatible filler materials, and the rigorous application of preheat and post-weld treatment. I have seen too many failed repairs that ignored these principles, and I commend the authors for their disciplined approach.
Zhuojin Pipe Fitting Co., Ltd