Deformation Behavior of Surfaced Bimetal During Cold Upsetting
Literature Overview and Background
The paper by Hui Youke, Wang Huajun, Xie Bing and Chen Wen, published in Forging & Stamping Technology (2017, Vol. 42, Issue 10), investigates the deformation behaviour of a bimetal material produced by plasma arc surfacing during cold upsetting. The study is supported by the National Natural Science Foundation of China (Project No. 51475346). The authors use cold upsetting experiments to explore the feasibility of forging the bimetal blank, which is a novel approach to manufacturing components with a hard wear-resistant surface and a tough core. The paper provides valuable insights into the interface characteristics and the deformation mechanisms of the bimetal.
Core Technical Points
Material Preparation and Characterisation
The authors prepared the bimetal by plasma arc surfacing, depositing a hard, wear-resistant alloy onto a steel substrate. The resulting bimetal has a distinct interface, known as the fusion line, which is critical to the performance of the component. The authors measured the microhardness across the interface and found that the weakest region is near the fusion line, while the surfacing layer has a much higher hardness than the substrate.
| Region | Microhardness (HV) | Observations |
|---|---|---|
| Substrate (base metal) | 200–250 | Relatively soft, ductile |
| Fusion line | 250–300 | Weakest region, potential for crack initiation |
| Surfacing layer | 500–700 | Hard, wear-resistant |
Deformation Behaviour During Cold Upsetting
The authors conducted cold upsetting experiments on the bimetal specimens and observed the deformation and failure modes. The key findings are:
- The substrate region deforms first, as it has a lower yield strength and higher ductility.
- The surfacing layer resists deformation, acting as a stiff shell that constrains the substrate.
- As the compression progresses, the surfacing layer eventually begins to deform, indicating that it has some plastic deformation capability.
The authors conclude that the bimetal has the potential for plastic deformation, which opens the door for forging as a manufacturing route.
Interface Characteristics and Failure Modes
The study reveals that the fusion line is the most critical region in terms of deformation and failure. The authors observed that cracking initiates near the fusion line during cold upsetting, which is consistent with the microhardness measurements. This is a crucial finding, as it highlights the importance of controlling the interface quality in bimetal components.
Engineering Practice and Lessons Learned
Case Study: Forging of Bimetal Blanks
The paper's findings have significant implications for the manufacturing of bimetal components. If the bimetal blank can be forged, it would allow the production of complex shapes with a hard surface and a tough core, which is highly desirable in applications such as wear plates, cutting tools, and rolls. However, the paper's observation that the fusion line is the weakest region is a warning that the forging process must be carefully controlled to avoid cracking at the interface.
Practical Considerations for Forging
| Parameter | Recommended Range | Rationale |
|---|---|---|
| Forging temperature | 800–1000°C | Reduces flow stress, improves ductility |
| Strain rate | 0.1–1.0 s⁻¹ | Avoids dynamic strain ageing |
| Reduction ratio | < 50% | Prevents cracking at the fusion line |
| Die design | Smooth, well-lubricated | Minimises friction and stress concentration |
| Post-forging cooling | Slow, controlled | Prevents residual stress and cracking |
Common Defects and Countermeasures
| Defect | Root Cause | Countermeasure |
|---|---|---|
| Cracking at fusion line | Weak interface, high stress | Control reduction ratio, improve interface quality |
| Delamination | Poor bonding at interface | Optimise surfacing parameters |
| Surface cracking | Excessive deformation | Reduce reduction ratio, increase temperature |
| Non-uniform deformation | Hardness mismatch | Optimise die design, use proper lubrication |
Study Insights and Implications
This paper is a valuable contribution to the understanding of bimetal deformation. The authors' systematic approach, combining microhardness measurements with cold upsetting experiments, provides a clear picture of the deformation mechanisms. The finding that the fusion line is the weakest region is particularly important, as it highlights the need for careful control of the interface quality in bimetal components. For the steel pipe and fitting industry, the principles are directly applicable to the production of clad pipes and fittings, where the interface between the base metal and the cladding is critical to performance.
Reference Value and Outlook
The paper is a well-designed experimental study that provides both fundamental insights and practical guidance. The authors' conclusion that the bimetal has the potential for plastic deformation is a significant finding, as it opens the door for forging as a manufacturing route for bimetal components. However, the paper also highlights the challenges, particularly the weak interface, which must be addressed through careful process control.
In conclusion, this paper is a valuable reference for any engineer involved in the manufacturing of bimetal components. The authors' rigorous approach and clear findings make it a useful guide for both research and industrial practice. I would recommend that any engineer considering forging of bimetal blanks study this paper carefully, as it provides essential data on the deformation behaviour and failure modes.
Zhuojin Pipe Fitting Co., Ltd