Macro-Segregation in Nickel-Based Alloy Surfacing on Low Alloy Steel
Literature Overview and Background
The paper by Ding Ming, Lu Li, Zhang Yu, Ding Yongsan, Yang Jia, Lü Yishi, Li Kejian and Cai Zhipeng, published in Hot Working Technology (2023, Vol. 52, Issue 15), investigates the macro-segregation in a dissimilar metal joint produced by surfacing a nickel-based alloy (ERNiCr-3) onto a T23 low alloy steel. The study is supported by the National Energy Group Science and Technology Project (GJNY-19-82). The authors use optical microscopy, scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) to characterise the microstructure at the welding interface. The paper provides a detailed understanding of the segregation mechanism and proposes practical measures to mitigate it.
Core Technical Points
Material System and Welding Process
The paper focuses on the surfacing of ERNiCr-3 (a nickel-chromium-iron alloy) onto T23 low alloy steel. This is a typical dissimilar metal joint, where the base metal and the filler material have significantly different compositions and properties. The key challenge is the formation of a transition zone at the interface, which can be susceptible to segregation, cracking, and premature failure.
Macro-Segregation Mechanism
The authors identify that macro-segregation occurs primarily at the overlap of adjacent weld beads. The mechanism is as follows:
- The nickel-based filler material has a lower liquidus temperature than the T23 base metal.
- At the overlap region, the local molten pool temperature is lower than the liquidus temperature of the base metal.
- The molten base metal, which has a higher liquidus temperature, flows into this region and rapidly solidifies due to the lower temperature.
- This rapid solidification traps the base metal composition in the weld, resulting in a banded structure with a higher Fe content and a crystal structure similar to the base metal.
The authors confirm this mechanism through microstructural analysis, which shows that the banded regions have a body-centred cubic (BCC) structure, consistent with the T23 base metal, while the surrounding weld metal has a face-centred cubic (FCC) structure, consistent with the nickel-based alloy.
Microstructural Characterisation
| Region | Crystal Structure | Composition | Observations |
|---|---|---|---|
| Weld metal | FCC | Ni-based | Austenitic, ductile |
| Banded region | BCC | Fe-rich | Ferritic, similar to base metal |
| Fusion line | Mixed | Transition | Weakest region, potential for cracking |
Mitigation Measures
The authors propose two practical measures to reduce macro-segregation:
- Select a filler material with a liquidus temperature closer to that of the base metal.
- Reduce the welding heat input to minimise the thermal gradient and the likelihood of the base metal flowing into the weld pool.
Engineering Practice and Lessons Learned
Case Study: Dissimilar Metal Welding in Power Plants
The paper's findings are directly relevant to the power generation industry, where dissimilar metal welds are common in boiler tubes, headers, and steam pipes. The T23 steel is a low alloy steel used in supercritical boiler applications, and the nickel-based alloy is used as a transition material to join it to austenitic stainless steel. The macro-segregation observed in this paper can lead to premature failure, particularly in high-temperature service where the banded regions may be susceptible to creep or corrosion.
Practical Considerations for Dissimilar Metal Welding
| Parameter | Recommended Range | Rationale |
|---|---|---|
| Filler material | Ni-based, liquidus close to base | Reduces segregation |
| Heat input | 0.8–1.2 kJ/mm | Minimises thermal gradient |
| Interpass temperature | 150–200°C | Controls cooling rate |
| Welding technique | String bead, minimal weaving | Reduces dilution |
| Post-weld heat treatment | 600–650°C, 1–2 hours | Relieves residual stress |
Common Defects and Countermeasures
| Defect | Root Cause | Countermeasure |
|---|---|---|
| Macro-segregation | Liquidus temperature mismatch | Select compatible filler, reduce heat input |
| Cracking | Hard, brittle banded regions | Control heat input, PWHT |
| Lack of fusion | Low heat input | Optimise parameters |
| Porosity | Contamination | Clean surface, dry electrodes |
Study Insights and Implications
This paper is an excellent example of the application of advanced characterisation techniques to solve a practical welding problem. The authors' use of EBSD to identify the crystal structure of the banded regions is particularly impressive, as it provides definitive evidence of the segregation mechanism. The finding that the liquidus temperature difference between the base metal and the filler material is the root cause of segregation is a valuable insight that can be applied to other dissimilar metal welding systems.
Reference Value and Outlook
The paper is a valuable reference for any engineer involved in dissimilar metal welding, particularly in the power generation and petrochemical industries. The authors' proposed mitigation measures, including the selection of a compatible filler material and the reduction of heat input, are practical and can be implemented without significant cost. For the steel pipe and fitting industry, the principles are directly applicable to the welding of clad pipes, where the interface between the base metal and the cladding must be carefully controlled.
In conclusion, this paper is a well-designed and thoroughly executed study that provides both fundamental insights and practical guidance. The authors' rigorous approach and clear findings make it a valuable resource for any engineer facing the challenge of dissimilar metal welding. I would recommend that any engineer involved in such welding study this paper carefully, as it provides essential data on the segregation mechanism and the measures to mitigate it.
Zhuojin Pipe Fitting Co., Ltd