ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Macro-Segregation in a Nickel-Based Surfacing on Low-Alloy Steel

Introduction

This paper from 2023 addresses a subtle but important problem in dissimilar metal welding: macro-segregation. The authors study a nickel-based alloy (ERNiCr-3) surfaced on a T23 low-alloy steel, and they identify the mechanism behind the formation of banded structures in the weld metal. This is a critical issue for power plant components, where nickel-based alloys are used to join low-alloy steel to stainless steel or to provide a corrosion-resistant layer. The paper's findings have direct implications for the selection of welding consumables and process parameters.

Technical Analysis of the Macro-Segregation Mechanism

The paper's key finding is that macro-segregation occurs primarily at the overlap between weld beads. This is a region where the molten pool is reheated by the subsequent weld pass, and the authors explain that this reheating causes a local decrease in temperature below the liquidus temperature of the base material. This causes the melted base material to solidify rapidly, forming a banded structure with a high iron content and a crystal structure similar to the base material.

The mechanism is elegantly explained by the difference in liquidus temperatures between the base material and the filler metal. The nickel-based filler has a lower liquidus temperature than the low-alloy steel base. When the weld pool is reheated at the overlap, the temperature drops below the liquidus of the base material, causing any unmelted base material particles to act as nucleation sites for rapid solidification. This results in a banded structure that is rich in iron and has a body-centered cubic (BCC) crystal structure, which is different from the face-centered cubic (FCC) structure of the nickel-based weld metal.

Parameter Low-Alloy Steel (T23) Nickel-Based Filler (ERNiCr-3)
Liquidus temperature Higher (e.g., 1500°C) Lower (e.g., 1350°C)
Crystal structure BCC (ferritic) FCC (austenitic)
Iron content High Low
Solidification behavior Rapid, if undercooled Slower, dendritic

The paper's recommendation to select a filler metal with a liquidus temperature closer to the base material is a practical solution. If the two materials have similar liquidus temperatures, the reheating at the overlap will not cause the base material to solidify prematurely. The paper also recommends reducing the heat input, which minimizes the size of the reheated region and reduces the likelihood of segregation.

Practical Considerations and Common Defects

In my experience, macro-segregation in dissimilar metal welds is a real problem, and it can lead to premature failure in service. The banded structures are often brittle and can act as crack initiation sites, especially under thermal cycling. The paper's findings are particularly relevant for power plant components, where the weld is subjected to high temperatures and thermal stresses. The veteran's advice is to pay close attention to the overlap between weld beads, as this is where the segregation is most likely to occur. A skilled welder will use a technique that minimizes the overlap, such as a straight bead rather than a weave, and will maintain a consistent travel speed to ensure a uniform heat input.

Another practical consideration is the use of a buttering layer. If you first deposit a layer of nickel-based alloy on the low-alloy steel, you can reduce the dilution and minimize the risk of segregation. This is a common practice in power plant welding, and the paper's findings support this approach. The buttering layer provides a transition zone that reduces the difference in liquidus temperatures and prevents the formation of the banded structure.

Study Insights and Implications

The paper's value lies in its detailed explanation of a complex metallurgical phenomenon. For the welding engineer, the key takeaway is that macro-segregation is not just a random occurrence; it is driven by the difference in liquidus temperatures between the base and filler metals. The paper's recommendations to select a filler with a closer liquidus temperature and to reduce heat input are practical and effective. The veteran's judgment is that the paper's findings are sound and should be incorporated into any welding procedure for dissimilar metal joints. The paper also highlights the importance of using advanced analytical tools, such as EBSD, to understand the microstructure of the weld metal.

In conclusion, the paper is a valuable contribution to the understanding of dissimilar metal welding. It provides a clear mechanism for macro-segregation and offers practical solutions to mitigate it. The paper is a must-read for any engineer involved in the welding of low-alloy steel to nickel-based alloys, and it reinforces the fundamental rule that the properties of the filler metal must be matched to the base material to ensure a sound weld.