ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Repair of S195 Diesel Engine Crankshaft Journals by Vibration Surfacing and Arc Spraying — A Shop Floor Review

Why Crankshafts Fail and What Repair Really Means

Every mechanic who has torn down an S195 single-cylinder diesel knows the story. These engines power irrigation pumps, small tractors, and stationary machinery across the Chinese countryside, and they run hard. The crankshaft is the heart of the machine, and the journal surfaces take the brunt of it — constant rubbing against the bearing shells, cyclic bending from combustion pressure, and the occasional starvation of oil when the operator forgets to check the sump. When the journals wear beyond the last undersize grinding limit, the shaft is usually scrapped. That is a waste of a good forging, and it is exactly the problem the authors set out to solve.

The paper selected four crankshafts that could not be ground to the final repair size, meaning the journals were already worn beyond the standard undersize steps. The decision to attempt repair rather than replacement is economically sound. A new crankshaft for an S195 is a significant cost, and the failure mode — journal wear — is a surface problem, not a bulk material problem. The core of the forging is still sound. The question is how to restore the surface, and the paper compares two routes: vibration surfacing and arc spraying.

Process Selection: Vibration Surfacing vs. Arc Spraying

The choice between these two processes is not trivial. Vibration surfacing, which is essentially a controlled low-heat-input arc welding process with the electrode oscillating at a set frequency, deposits a thin, metallurgically bonded layer. The bond is true fusion, and the deposit can be machined and ground to a finish comparable to the original journal. The downside is heat input. Even with vibration, you are putting heat into a shaft that has been through a full heat treatment cycle, and you risk distortion and residual stress.

Arc spraying is a different animal. You feed a wire into an arc, melt it, and atomize the molten metal with compressed air. The droplets fly onto the prepared surface, splat, and cool rapidly. The bond is mechanical and semi-metallurgical — the droplets penetrate surface roughness and key into the substrate. Heat input to the shaft is minimal because the spray stream is hot but the substrate stays relatively cool. The coating is porous, however, and the bond strength is lower than a fused deposit.

Parameter Vibration Surfacing Arc Spraying
Bond mechanism Fusion (metallurgical) Mechanical interlock + partial metallurgical
Heat input to substrate Moderate to high Low
Coating density Fully dense Porous (5–15% porosity typical)
Bond strength High (equivalent to weld) Moderate (30–60 MPa typical)
Distortion risk Significant Minimal
Post-coating machining Grind, possible stress relief Grind only
Typical deposit thickness 1–3 mm per pass 0.5–2 mm per pass

The authors used both methods on different journals of the same crankshafts, which is a smart experimental design. It allows a direct comparison on the same component, under the same service conditions. The vibration surfacing was applied to some journals and arc spraying to others, and then the whole shaft was ground and installed.

Metallurgical and Mechanical Considerations

The critical question for any repair is whether the coating will stay on the shaft. The authors report that after eccentric grinding and normal grinding, the coating showed good bonding with no peeling or spalling. That is the first hurdle cleared. But the real test is under load.

The coating must also have adequate hardness and wear resistance. Vibration surfacing deposits are typically harder than the original journal material because of the rapid solidification and fine grain structure. Arc-sprayed coatings are harder than the substrate in the as-sprayed condition, but the porosity can reduce load-bearing capacity. The authors do not report hardness numbers in the abstract, but the successful run-in and load operation suggests the coatings performed adequately.

One concern that any experienced engineer would raise is the fatigue behavior of the repaired journal. The crankshaft is a fatigue-loaded component. Any surface defect, porosity, or residual tensile stress in the coating can initiate a crack. The vibration surfacing deposit, being a weld metal, will have residual tensile stress in the as-deposited condition. Arc-sprayed coatings are usually in a state of low residual stress, but the porous structure can act as crack initiation sites under cyclic loading.

The authors ran a bench run-in and load operation after installation. This is the right approach. A crankshaft repair is not complete until it has run under load. The fact that the shafts performed without coating failure is a strong positive signal.

Machining and Grinding After Repair

The paper mentions both eccentric and normal grinding. This is a critical detail. When a journal is worn, it may not be worn uniformly. An eccentric grind corrects the journal geometry by removing material from the high side to bring the journal back to concentricity. This is standard practice for crankshaft repair.

The grinding operation on a coated journal is where things can go wrong. The coating is thin — typically 0.5 to 2 mm — and the grinding wheel must be dressed properly to avoid loading. Arc-sprayed coatings are abrasive and can load the wheel quickly. The operator must use the correct wheel grade and grinding parameters. The authors report that grinding was successful, which suggests the coating hardness was within a grindable range.

Testing and Service Validation

The bench run-in and load operation is the ultimate test. The authors report that the coating bonded well with no peeling or spalling after the run. This is the result that matters. A coating that survives grinding, installation, run-in, and load operation is a coating that will survive in service.

The key insight from this paper, from a practical standpoint, is that both methods work, but they work differently. Vibration surfacing gives a strong, dense, metallurgically bonded layer that is suitable for heavily loaded journals. Arc spraying gives a lower-heat-input repair that minimizes distortion, which is important for a crankshaft that must maintain its geometry. The choice depends on the specific condition of the shaft and the repair shop's capabilities.

Lessons from the Shop Floor

I have seen too many repair jobs fail because the shop did not understand the difference between a surface repair and a structural repair. A crankshaft journal is a surface that carries a load. The coating must be thick enough to restore the journal to size, hard enough to resist wear, and bonded well enough to transmit the load to the substrate.

The paper demonstrates that a well-executed repair can extend the life of a component that would otherwise be scrapped. This is the essence of good engineering — not just designing new things, but making the existing things last longer.

The practical takeaway for any repair shop: do not underestimate the importance of surface preparation. Both vibration surfacing and arc spraying require a clean, roughened surface for good bonding. The authors clearly understood this, and the results show it. The four crankshafts were repaired, ground, installed, and run successfully. That is a good outcome, and it is a lesson worth keeping in mind the next time someone tells you a component is beyond repair.