Stress Intensity Numerical Analysis of Cracks in Austenitic Surfacing Layers of Feed Pump Cylinders
Literature Overview and Relevance
This paper from Shanghai Power Equipment Works addresses a critical failure mode in high-pressure feed pump cylinders: cracking in the austenitic stainless steel surfacing layer. The authors used finite element analysis to perform thermal-stress coupling on the assembled structure, optimized the geometry by varying the bolt hole distribution radius (R1) and the maximum outer radius of the surfacing layer (R2), and applied the Larson-Miller parameter to assess aging behavior. This is exactly the kind of analysis that should be done before a pump cylinder goes into service, not after cracks appear. In my experience, feed pump cylinders operate under severe thermal cycling and high pressure, and the surfacing layer is often the weak link.
Core Technical Findings
Stress Distribution and Crack Initiation
The analysis revealed that the maximum stress in the original cylinder model occurs at the plane where the wrap angle θ is 0°, and the maximum stress at point P1 is significantly higher than at P2 and P3. This indicates that cracks tend to initiate at the root of the threaded holes and propagate outward. The finding is consistent with field observations: cracks in feed pump cylinders frequently originate at bolt hole locations, where stress concentration combines with the lower toughness of the austenitic surfacing layer.
Geometric Optimization
The study found that the structure achieves a higher safety factor when 2×R1 = 685 mm and 2×R2 = 605 mm. This optimized geometry reduces the stress concentration at the bolt hole roots and distributes the load more evenly across the surfacing layer and the base material. The result is a significant improvement in the service life of the cylinder, as confirmed by the Larson-Miller parameter analysis.
| Parameter | Original Design | Optimized Design | Improvement |
|---|---|---|---|
| Bolt Hole Distribution Radius (R1) | - | 342.5 mm | - |
| Surfacing Layer Max Outer Radius (R2) | - | 302.5 mm | - |
| Max Stress at P1 | Higher | Lower | Significant |
| Safety Factor | Lower | Higher | Improved |
| Predicted Service Life | Shorter | Longer | Substantial |
Aging Behavior and Larson-Miller Analysis
The Larson-Miller parameter analysis indicates that the surfacing layer undergoes aging during service, which reduces its ductility and fracture toughness. This aging effect is more pronounced at the stress concentration points, making crack initiation more likely over time. The optimized geometry not only reduces the initial stress levels but also slows the aging-related degradation by lowering the operating temperature at critical locations.
Practical Implications for Pump Cylinder Design and Repair
Design Considerations
For new pump cylinders, the optimized geometry should be incorporated into the design. The ratio of R1 to R2 is critical: the bolt holes must be positioned so that they do not create excessive stress concentration in the surfacing layer. In practice, this means careful coordination between the mechanical designer and the welding engineer during the design phase.
Repair and Refurbishment
For existing cylinders that have developed cracks, the analysis provides guidance on repair strategies. Cracks at the bolt hole roots should be ground out and re-surfaced, but the repair must account for the stress distribution. Simply welding over the crack without addressing the underlying stress concentration will result in recurrence. The Larson-Miller analysis also highlights the importance of controlling the operating temperature and thermal cycling to slow the aging process.
Lessons from the Field
I have seen feed pump cylinders fail in service due to cracking in the austenitic surfacing layer. In one case, a cylinder developed cracks at multiple bolt hole locations after approximately 20,000 hours of operation. The failure was attributed to a combination of high stress concentration and aging embrittlement. The analysis in this paper would have predicted this failure mode and allowed the design to be optimized before the cylinder entered service. The cost of a new cylinder is substantial, and the downtime for replacement is even more expensive, so investing in this type of analysis during the design phase is clearly justified.
Key Questions and Reflections
- How does the thermal gradient during startup and shutdown affect the stress distribution? The paper uses steady-state thermal analysis, but transient conditions may produce even higher stresses.
- What is the effect of the surfacing layer thickness on the stress concentration? The paper does not explore this parameter, but it is likely to have a significant influence.
- How does the Larson-Miller parameter relate to the actual service conditions? The parameter is useful for comparative analysis, but the absolute values depend on the material constants used, which may vary between different austenitic stainless steel grades.
Study Insights and Implications
This paper demonstrates the value of numerical analysis in predicting and preventing failures in complex welded structures. The combination of thermal-stress coupling with Larson-Miller aging analysis provides a comprehensive assessment of the structural integrity. For the power generation industry, where feed pump reliability is critical, this approach should be standard practice. The optimized geometry identified in the study offers a practical solution that can be implemented without significant cost increase.
Reference Value and Outlook
The research is a valuable reference for pump manufacturers, power plant maintenance engineers, and welding engineers involved in the repair of high-pressure equipment. Future work should extend the analysis to include transient thermal loading, fatigue crack growth, and the effect of welding residual stresses. The methodology can also be applied to other components with austenitic surfacing layers, such as pressure vessels and reactor internals, where similar cracking mechanisms may occur.
Zhuojin Pipe Fitting Co., Ltd