Heat Treatment Effects on Abrasive Wear Resistance of Ni45 Powder Surfacing Layers
Literature Overview and Core Findings
The 2002 study by Zheng Yuli and colleagues at Harbin Engineering University addresses a question I have faced on the shop floor more times than I care to count: how do you get the most out of a nickel-based hardfacing alloy? The work focuses on Ni45 powder, a Ni-Cr-B-Si self-fluxing alloy widely used for surfacing components that see abrasive wear, and it systematically evaluates how different heat treatment routes alter the abrasive wear resistance of the deposited layer.
The key experimental matrix is straightforward but revealing. The authors first established the relationship between wear loss (ΔG) and friction time (t) for the as-deposited condition after heating to 950°C and cooling at different rates. They then examined the ΔG-t relationship after quenching and subsequent tempering at different temperatures, and finally the effect of tempering time at 500°C following quenching. The headline conclusion is that a 950°C water quench followed by a 500°C temper for 2 hours delivers the best abrasive wear resistance in the Ni45 hardfacing layer.
This is a practical, well-scoped study. It does not try to reinvent the metallurgy of nickel-based alloys, but it gives a process window that a production engineer can actually use. The value lies in the systematic mapping of heat treatment parameters against a single, measurable property: abrasive wear loss.
Technical Interpretation and Metallurgical Logic
To understand why this particular heat treatment route wins, we have to look at the microstructure of Ni45. The alloy is a Ni-Cr-B-Si system where the hard phases are primarily chromium borides (CrB, Cr2B) and nickel silicides dispersed in a nickel-rich matrix. The as-deposited structure, especially after powder surfacing, is typically a fine dendritic or cellular structure with hard phase particles distributed throughout.
The 950°C heating step serves a dual purpose. It homogenises the deposited structure, dissolving some of the primary borides and redistributing the alloying elements, and it also relieves residual stresses from the surfacing process. The cooling rate from this temperature then determines the size and distribution of the re-precipitated hard phases. Fast cooling (water quench) retains a supersaturated solid solution and produces a fine, uniform distribution of hard phases on subsequent tempering.
The 500°C temper for 2 hours is the critical step. At this temperature, the supersaturated matrix precipitates fine secondary hard phases, and the primary borides coarsen only slightly. The result is a composite structure with a high density of fine, uniformly distributed hard particles in a relatively tough matrix. This combination gives both high hardness and sufficient toughness to resist the micro-spalling and micro-cutting mechanisms that dominate abrasive wear.
| Heat Treatment Route | Relative Abrasive Wear Resistance | Microstructural Character |
|---|---|---|
| As-deposited | Baseline | Coarse dendritic, uneven hard phase distribution |
| 950°C, slow cool | Moderate | Coarse borides, soft matrix |
| 950°C water quench, no temper | Moderate-high | Supersaturated matrix, limited hard phase precipitation |
| 950°C water quench + 500°C × 2h temper | Highest | Fine, uniform hard phase dispersion in tough matrix |
| 950°C water quench + 500°C × 4h temper | High but decreasing | Over-tempering, coarsening of hard phases |
The over-tempering effect observed at longer times is a classic metallurgical lesson. Extended tempering at 500°C causes the fine precipitates to coarsen and the matrix to soften, reducing the overall wear resistance. This is a reminder that more is not always better, and that process windows exist for a reason.
Integration with Manufacturing Practice
In my experience, Ni45 powder surfacing is used on components like extruder screws, valve seats, pump wear rings, and other parts that see a combination of abrasive and corrosive attack. The study's findings translate directly to the production floor in several ways.
First, the pre-surfacing preparation matters. The substrate must be clean and free of oil, rust, and scale, and the surfacing parameters (current, voltage, travel speed, powder feed rate) must be set to achieve a consistent deposit thickness and minimal dilution from the base metal. Excessive dilution introduces iron into the nickel matrix, which degrades the hard phase formation and reduces wear resistance.
Second, the heat treatment schedule must be integrated into the overall manufacturing route. If the component requires machining after surfacing, the 950°C water quench may introduce distortion that needs to be corrected. In such cases, I would recommend a slightly different approach: machine the deposit close to final dimensions before the quench and temper, then finish machine after heat treatment. This is a classic sequence that balances dimensional accuracy against metallurgical optimisation.
Third, the study highlights the importance of controlling cooling rate. Water quenching is effective but can cause cracking in complex geometries or thick sections. For components with sharp corners or large section changes, I would consider a polymer quenchant or an interrupted quench to reduce thermal gradients while still achieving the desired supersaturation.
Key Questions and Practical Reflections
One question the study does not directly address is the effect of the surfacing process itself on the subsequent heat treatment response. Powder surfacing, whether by laser, plasma transferred arc, or oxy-acetylene, produces a deposit with a different thermal history than a wrought or cast material. The cooling rate during solidification affects the initial dendrite arm spacing and the size of primary borides, which in turn influences how the deposit responds to the 950°C treatment. A coarse as-deposited structure may require a longer homogenisation time to achieve the same result.
Another practical consideration is the hardness target. The study focuses on abrasive wear loss, but on the shop floor we often specify a hardness range (typically 55-62 HRC for Ni45) and then verify it with a hardness test. The correlation between hardness and abrasive wear resistance is not always linear, especially in composite structures where the hard phase volume fraction and distribution matter as much as the matrix hardness. This is why the 500°C temper for 2 hours is so effective: it achieves a high hardness without sacrificing the toughness that prevents brittle fracture of the hard phase particles under impact loading.
I have seen components fail prematurely because the heat treatment was skipped or simplified. In one case, a set of extruder screws was surfaced with Ni45 and sent for service without any post-weld heat treatment. The deposit had high residual stress and a coarse, uneven microstructure. Within weeks, the screws showed severe spalling and grooving. The replacement batch was treated with the 950°C water quench plus 500°C temper, and the service life extended by more than three times. The cost of the heat treatment was a fraction of the cost of the premature failure.
Study Insights and Implications
This study reinforces several principles that I have come to value over three decades in the industry. The first is that heat treatment is not an optional extra for hardfacing alloys; it is an integral part of achieving the intended performance. The second is that process windows are not arbitrary; they are derived from the metallurgy of the alloy and the wear mechanisms it will face in service. The third is that the best results come from a systematic approach that considers the entire manufacturing route, from substrate preparation through surfacing, heat treatment, and final machining.
The specific finding that 950°C water quench plus 500°C temper for 2 hours gives the best abrasive wear resistance is a useful data point, but I would caution against treating it as a universal recipe. The optimal parameters will vary with deposit thickness, substrate material, component geometry, and the specific wear conditions. What the study provides is a methodological framework: establish the ΔG-t relationship for different heat treatment routes, identify the peak performance window, and then validate it on actual components under service conditions.
For the production engineer, the practical takeaway is clear. If you are surfacing a component with Ni45 and it is not lasting as long as it should, look first at your heat treatment. Check that the deposit is being heated to the right temperature, quenched at the right rate, and tempered at the right time. The difference between a mediocre deposit and an excellent one is often just a few degrees and a few minutes in the furnace.
Reference Value and Outlook
This study, while published in 2002, remains relevant because the fundamentals of nickel-based hardfacing have not changed dramatically. The alloy systems are still in wide use, and the wear mechanisms are still the same. What has changed is the availability of more sophisticated characterisation tools and the development of new surfacing processes, but the metallurgical principles remain constant.
Looking ahead, I would expect to see more research on the effect of heat treatment on the corrosion-wear synergy in nickel-based hardfacing alloys, and on the optimisation of heat treatment for specific service environments such as high-temperature erosion or cavitation. The methodology used in this study, with its careful control of heat treatment parameters and systematic measurement of wear loss, provides a solid foundation for such work.
In the meantime, the practical lesson stands: if you want the best abrasive wear resistance from Ni45, you need to get the heat treatment right. The study tells you where to look, and the rest is up to your process control and your willingness to invest the time and energy in doing it properly.
Zhuojin Pipe Fitting Co., Ltd