Effects of Boron on the Microstructure and Properties of Hardfacing Alloys
Literature Overview and Core Findings
The 1998 study by Shi Rongchang and Ge Changlu at China University of Mining and Technology tackles a question that has puzzled hardfacing engineers for decades: what exactly does boron do in a hardfacing alloy, and how much of it should you add? The work systematically examines the effect of varying boron content on the microstructure and mechanical properties of a hardfacing alloy, with particular attention to hardness, abrasive wear resistance, and impact toughness.
The findings are presented in a clear, almost intuitive manner. As boron content increases, the hardness and wear resistance of the hardfacing layer steadily improve. At the same time, the microstructure undergoes a progressive transformation, moving from a hypoeutectic state through a hypereutectic state, then to a eutectic state, and finally to a hypereutectic state. The study identifies two critical points: the eutectic or near-eutectic microstructure offers the best impact toughness, while the near-eutectic hypereutectic composition delivers the highest hardness and wear resistance.
This is a deceptively simple conclusion with profound implications. It tells us that boron is not just a hardener; it is a microstructure modifier that fundamentally changes the balance between hardness and toughness. The alloy design problem becomes one of selecting the right boron content to match the service conditions.
Technical Interpretation and Metallurgical Logic
Boron is a powerful alloying element in hardfacing alloys because of its strong affinity for iron and chromium. It forms hard borides such as Fe2B, FeB, CrB, and Cr2B, which precipitate as primary phases or as part of the eutectic structure. The amount of boron determines the volume fraction and morphology of these hard phases, and it also shifts the position of the alloy relative to the eutectic point.
In a low-boron alloy, the microstructure is hypoeutectic: primary austenite or ferrite dendrites form first, with the eutectic (austenite plus borides) filling the interdendritic regions. This structure has good toughness but relatively low hardness because the hard phase volume fraction is limited. As boron increases, the alloy approaches the eutectic composition, where the entire structure consists of fine, uniformly distributed borides in a matrix. This eutectic structure has an excellent combination of hardness and toughness, because the hard phases are finely dispersed and the matrix provides sufficient ductility to absorb impact energy.
Beyond the eutectic point, the alloy becomes hypereutectic. Primary borides form first, and these are typically coarse and blocky. The hardness increases further because of the high volume fraction of hard phase, but the toughness drops sharply because the coarse primary borides act as crack initiation sites. The study found that the near-eutectic hypereutectic composition gives the best hardness and wear resistance, but the eutectic or near-eutectic composition gives the best impact toughness.
| Boron Content | Microstructure | Hardness | Wear Resistance | Impact Toughness |
|---|---|---|---|---|
| Low | Hypoeutectic (primary austenite + eutectic) | Moderate | Moderate | High |
| Medium (near-eutectic) | Eutectic (fine borides + matrix) | High | High | Highest |
| Medium-high (near-eutectic hypereutectic) | Hypereutectic (primary borides + eutectic) | Highest | Highest | Moderate |
| High | Hypereutectic (coarse primary borides) | Very high | High | Low |
The practical implication is that the optimal boron content depends on the dominant wear mechanism. For pure abrasive wear, where the component sees no significant impact loading, the near-eutectic hypereutectic composition is the best choice. For applications that involve both abrasion and impact, such as crusher hammers or shovel teeth, the eutectic or near-eutectic composition provides a better balance.
Integration with Manufacturing Practice
In my experience, boron-containing hardfacing alloys are used in a wide range of applications, from agricultural implements to mining equipment, and from cement plant components to steel mill rolls. The study's findings have direct relevance to the selection of hardfacing consumables and the design of the hardfacing process.
First, the boron content of the hardfacing consumable must be matched to the expected service conditions. If the component sees primarily abrasive wear with minimal impact, a high-boron alloy is appropriate. If the component sees a combination of abrasion and impact, a lower-boron alloy is safer. I have seen components fail prematurely because a high-boron alloy was used in an impact application, leading to spalling and catastrophic fracture of the hardfacing layer.
Second, the dilution from the base metal must be carefully controlled. Boron is a strong hardener, but it is also a strong deoxidiser, and it can react with oxygen and nitrogen in the weld pool to form oxides and nitrides that reduce the effectiveness of the hardfacing layer. The dilution rate, which is influenced by welding current, travel speed, and the thickness of the deposit, determines the final boron content of the hardfacing layer. A high dilution rate can reduce the boron content below the optimal level, while a low dilution rate can leave the deposit with a boron content that is too high.
Third, the heat input must be managed to avoid excessive grain growth and boride coarsening. Boron-containing alloys are sensitive to thermal history, and a high heat input can produce coarse primary borides that reduce toughness. I would recommend using a relatively low heat input with a multi-pass technique to build up the deposit, rather than a single pass with high current.
Key Questions and Practical Reflections
One question that the study does not fully address is the effect of boron on the corrosion resistance of the hardfacing layer. Boron is generally considered to have a neutral or slightly negative effect on corrosion resistance, because the borides are cathodic relative to the matrix and can promote galvanic corrosion. In applications where the component sees both abrasive wear and corrosive attack, such as slurry pumps or flue gas desulphurisation systems, the boron content must be balanced against the need for corrosion resistance.
Another consideration is the effect of boron on the weldability of the hardfacing alloy. High-boron alloys tend to have poor weldability because the borides have a high melting point and a low coefficient of thermal expansion, which can lead to cracking during solidification. This is particularly problematic for thick deposits or complex geometries. In such cases, I would recommend a preheat and a controlled interpass temperature to reduce the risk of solidification cracking.
I recall a project where a set of fan blades for a cement plant was hardfaced with a high-boron alloy to resist abrasive wear from the raw material feed. The initial results were excellent, with the blades lasting three times longer than the previous hardfacing. However, the blades developed cracks at the weld toes after a few weeks of service, and the cracks propagated into the base metal. The root cause was a combination of high residual stress from the hardfacing process and the low toughness of the high-boron deposit. The solution was to switch to a near-eutectic alloy with a slightly lower boron content, which provided adequate wear resistance while improving the toughness and reducing the risk of cracking.
Study Insights and Implications
This study provides a clear and systematic framework for understanding the role of boron in hardfacing alloys. It demonstrates that the boron content is not just a matter of "more is better"; there is an optimal range that balances hardness and wear resistance against toughness and weldability.
The key insight is that the microstructure, and hence the properties, can be tailored by controlling the boron content. For applications that demand maximum wear resistance, the near-eutectic hypereutectic composition is the target. For applications that demand a balance of wear resistance and impact toughness, the eutectic or near-eutectic composition is the choice. For applications that demand maximum toughness, the hypoeutectic composition is the answer.
The study also highlights the importance of understanding the phase diagram of the alloy system. The eutectic point is a critical reference, and the properties of the alloy change dramatically as the composition moves across it. This is a fundamental concept that every hardfacing engineer should understand.
Reference Value and Outlook
The principles established in this study remain as relevant today as they were in 1998. Boron is still a key alloying element in many hardfacing consumables, and the trade-off between hardness and toughness is still a central design consideration.
Looking ahead, I would expect to see more research on the effect of boron in combination with other alloying elements, such as vanadium, niobium, and titanium, which can form additional hard phases and further modify the microstructure. I would also expect to see more work on the effect of boron on the high-temperature properties of hardfacing alloys, particularly for applications in the power generation and cement industries.
For the production engineer, the practical takeaway is clear. When selecting a hardfacing consumable, do not just look at the hardness specification. Consider the boron content, the microstructure it will produce, and the service conditions the component will face. The difference between a long-lived hardfacing layer and a premature failure is often just a few tenths of a percent of boron.
Zhuojin Pipe Fitting Co., Ltd