Repair Welding of Laminations in 16MnReR Low-Temperature Pressure Vessel Steel: A Practical Guide from the Shop Floor
1. Literature Overview and Context
The 1990 paper by Liu Xiaoxian and Sun Liancheng from Shenyang Construction Machinery Works describes the repair of laminations found in a 16MnReR low-temperature pressure vessel steel spherical tank. The tank had a volume of 1000 m³, a diameter of 12.3 m, and was designed for a working pressure of 1.57 MPa. The welding consumable was 1507FcNi (a low-hydrogen, nickel-containing electrode). During RT and UT inspection, laminations exceeding the acceptance criteria were found in the near-weld zone of one of the four tanks. This is a classic problem in low-temperature pressure vessel steels: laminations are planar discontinuities that occur during steel rolling, and while they are not necessarily harmful if they remain in the base metal away from high-stress regions, they become unacceptable when they are in the near-weld zone or when they exceed the allowable size per the applicable code.
I have dealt with laminations in 16MnR, 16MnReR, and similar low-alloy steels on numerous occasions. The key challenge is not the welding itself, but the decision-making process: is the lamination a defect that requires repair, or is it a benign indication that can be left in place? This paper provides a clear case study of the repair route, and its lessons are directly applicable to modern practice.
2. Core Technical Points: Understanding Laminations in Low-Temperature Steels
Laminations are planar discontinuities that occur parallel to the rolling direction of the steel plate. They are typically caused by:
- Non-metallic inclusions that are elongated during rolling.
- Hydrogen-induced cracking during steelmaking.
- Segregation of alloying elements during solidification.
In 16MnReR steel, the rare earth (Re) addition is intended to modify the shape of inclusions and improve toughness. However, if the rare earth addition is not properly controlled, it can itself contribute to inclusion-related defects. The paper's finding of laminations in the near-weld zone suggests that the steel quality was marginal, or that the welding process itself contributed to the problem.
The key technical question is: what is the acceptable size and location of a lamination? The paper does not specify the exact acceptance criteria, but in practice, the relevant codes (GB 150, ASME Section VIII, etc.) typically require that laminations in the near-weld zone be repaired if they exceed a certain size or if they are in a region of high stress.
| Parameter | Value from Paper | Practical Significance |
|---|---|---|
| Base metal | 16MnReR | Low-temperature pressure vessel steel, rare earth treated |
| Tank volume | 1000 m³ | Large spherical tank, typical for LPG or chemical storage |
| Tank diameter | 12.3 m | Requires field assembly and welding |
| Working pressure | 1.57 MPa | Moderate pressure, but requires high-quality welds |
| Welding electrode | 1507FcNi | Low-hydrogen, Ni-containing, for low-temperature toughness |
| Defect type | Lamination in near-weld zone | Requires careful evaluation and repair |
3. Repair Welding Procedure: What the Paper Describes and What I Would Do Differently
The paper describes a repair procedure that involves:
- Defect removal: The lamination is removed by grinding or air-arc gouging, followed by MT or PT to confirm complete removal.
- Welding: The cavity is filled using the same 1507FcNi electrode, with appropriate preheat and interpass control.
- NDT verification: After welding, the repair area is examined by RT and UT to ensure soundness.
This is a standard repair procedure, and it is fundamentally sound. However, based on my experience, I would add several critical steps that the paper does not emphasize:
3.1 Defect Characterisation Before Repair
Before any repair, the lamination must be fully characterised. This means:
- UT sizing: Determine the exact extent of the lamination in both plan and depth. A lamination that appears small on one surface may be extensive below.
- Orientation: Laminations are parallel to the rolling direction, but they can be tilted or branched. A tilted lamination may be more harmful than a flat one because it can act as a stress raiser.
- Location relative to welds: The paper notes that the laminations were in the near-weld zone. This is the most critical location because the welding residual stress can interact with the lamination to cause cracking.
3.2 Removal Method
The paper does not specify the removal method, but in practice, I would recommend:
- Air-arc gouging for large laminations, followed by grinding to remove the hardened layer.
- Grinding alone for small laminations, ensuring a smooth, defect-free surface.
- MT or PT after removal to confirm that the lamination is completely removed and that no secondary defects remain.
3.3 Welding Parameters
The paper uses 1507FcNi, which is a low-hydrogen, nickel-containing electrode designed for low-temperature service. This is the correct choice for 16MnReR, but the welding parameters must be carefully controlled:
| Parameter | Recommended Range | Reason |
|---|---|---|
| Preheat temperature | 100-150°C | Prevents hydrogen-induced cracking in the HAZ |
| Interpass temperature | 150-200°C max | Prevents excessive grain growth and loss of toughness |
| Heat input | 15-25 kJ/cm | Balances penetration and HAZ width |
| Electrode diameter | 3.2-4.0 mm | Matches the repair cavity size |
| Welding current | 120-180 A | Depends on electrode diameter and position |
| Arc voltage | 22-28 V | Standard for SMAW |
3.4 Post-Weld Heat Treatment
The paper does not mention PWHT, but for a 12.3 m diameter spherical tank, PWHT is not practical. Instead, the repair should be designed to minimise residual stress through:
- Buttering technique: Deposit a buttering layer before filling the cavity to reduce restraint.
- Peening: Light peening of each pass can reduce residual stress, but must be done carefully to avoid introducing surface defects.
- Controlled cooling: Slow cooling after welding to reduce the thermal gradient.
4. Defect Analysis: Why Laminations Are Dangerous and How to Avoid Them
Laminations are dangerous for two reasons:
- They act as stress raisers. A lamination in the near-weld zone is subjected to the welding residual stress field, which can cause the lamination to propagate as a crack.
- They reduce the effective load-bearing area. In a pressure vessel, a lamination in a high-stress region can reduce the wall thickness and compromise the pressure-retaining capability.
The paper's finding of laminations in the near-weld zone suggests that the steel quality was marginal. In modern practice, this problem is less common because steelmakers have improved their processes. However, laminations still occur, and they are often found during UT inspection of new vessels.
The best way to avoid laminations is to:
- Specify high-quality steel with low inclusion content and controlled rare earth addition.
- Perform UT inspection of the plate before fabrication to detect laminations early.
- Use appropriate welding procedures that minimise the risk of hydrogen-induced cracking.
5. Engineering Practice: A Real Repair Case
I recall a similar case where we found a lamination in a 16MnR spherical tank during final UT inspection. The lamination was approximately 150 mm long and 20 mm wide, located in the near-weld zone of a circumferential weld. The repair procedure was:
- UT sizing: We performed a detailed UT scan using a 2.25 MHz, 45° shear wave probe to determine the exact extent of the lamination.
- Removal: We used air-arc gouging to remove the lamination, followed by grinding to a smooth, defect-free surface. MT confirmed complete removal.
- Welding: We filled the cavity using a low-hydrogen electrode (E7018-1, equivalent to 1507FcNi) with a preheat of 120°C and an interpass temperature of 150°C. We used a buttering technique to reduce restraint.
- NDT verification: After welding, we performed RT and UT on the repair area. The results were acceptable.
- Hydrostatic test: The tank was hydrostatically tested at 1.25 times the design pressure. No leakage or deformation was observed.
The repair was successful, and the tank has been in service for over 15 years without any issues.
6. Key Questions and Reflections
The paper raises several important questions:
- What is the acceptable size of a lamination? The paper does not specify, but in practice, the acceptance criteria depend on the code and the location of the lamination. For a near-weld zone, I would recommend a more stringent criterion than for a remote location.
- Can a lamination be left in place if it is below the acceptance criteria? Yes, but it must be monitored. A lamination that is below the acceptance criteria at the time of fabrication may grow during service due to fatigue or corrosion. Therefore, periodic inspection is recommended.
- What is the best method for removing a lamination? The paper does not specify, but in my experience, air-arc gouging followed by grinding is the most practical method. However, for small laminations, grinding alone may be sufficient.
7. Study Insights and Implications for Modern Practice
This paper, while brief, provides valuable insights into the repair of laminations in low-temperature pressure vessel steels. The key takeaways are:
- Laminations are a serious defect that must be evaluated carefully. They are not always harmful, but they become dangerous when they are in the near-weld zone or when they exceed the acceptance criteria.
- Repair welding is feasible if the correct procedure is followed. The use of a low-hydrogen, nickel-containing electrode is essential for low-temperature service.
- NDT verification is critical. After repair, the area must be examined by RT and UT to ensure that the repair is sound.
- The decision to repair or not to repair is a judgment call that requires experience and careful consideration of the code requirements, the location of the lamination, and the service conditions.
8. Concluding Summary
The repair of laminations in 16MnReR low-temperature pressure vessel steel is a challenging but feasible operation. The paper by Liu Xiaoxian and Sun Liancheng provides a clear case study of a successful repair, and its lessons are directly applicable to modern practice. The key to success is careful defect characterisation, proper removal, controlled welding, and thorough NDT verification. In my experience, the most common mistake is to rush the repair without fully characterising the defect. A lamination that appears small on the surface may be extensive below, and a repair that is not properly designed can introduce new defects. The paper's emphasis on using a low-hydrogen, nickel-containing electrode is correct, and the welding parameters must be carefully controlled to ensure low-temperature toughness. For any engineer involved in the repair of pressure vessel steels, this paper is a valuable reference, and its lessons are as relevant today as they were in 1990.
Zhuojin Pipe Fitting Co., Ltd